Lloydies Garage

Пікірлер

@edbertdastan624 14 күн бұрын

Good job by James from tanzania.

@mycroftrodriguez9059 2 ай бұрын

Is it doing well?

@VS-q 2 ай бұрын

Thanks mate, nice vid. Looks like a bit harder than doing Prado. How those GSP drive shafts are going?

@farmerdeanoutlookcomau 3 ай бұрын

What vehicle is it ?

@farmerdeanoutlookcomau 3 ай бұрын

Key bangers will do that hahahaha! First time that happened to me an almighty scraping sound immediately happened! I realised it was the muffler dragging on the bitumen on my HZ ute. I thought I’d really buggered something up heavy .

@farmerdeanoutlookcomau 3 ай бұрын

Haha I was watching a video on rumble a minute ago about the government wanting us to reduce eating meat ! Go mate, I made myself a smoker out of a 45 this year too. I cut around the underside of the weld at the top and there’s an inner ring or rebate of sorts there that centres it back into place. I didn’t plan that it was an accident. I would have welded locating lugs or something but accidentally didn’t have to. Works a treat ! Thanks for subbing to my channel too mate.

@Animalexotic98 3 ай бұрын

WTF THERE HUGE AND AT NIGHT?!?!

@xterrorx8376 6 ай бұрын

Good video, but that's not how you pack bearings, you only get a small amount on the outside and nothing in the actual bearing case

@lloydiesgarage4214 6 ай бұрын

That's how it's always been done

@xterrorx8376 6 ай бұрын

@lloydiesgarage4214 alot of people do it like that, but if you want them to last longer use a bearing packer, they're not expensive and it packs them properly, most of what you used will just end up in the hub not the bearing

@ReubenMwiti-gb7yh 8 ай бұрын

Nice job

@ReubenMwiti-gb7yh 8 ай бұрын

Nice job engineer, watching life in Fastlink international garage juba South Sudan 💪💪💪💪

@burgertliebenberg1478 9 ай бұрын

Thank you helped alot.. On the same vehicle(Hilux), do you have a sump gasket repair?

@Ballzdp84 9 ай бұрын

Pretty impressive

@OutbackOutlaw 11 ай бұрын

Far out!!

@Shadow-11158 11 ай бұрын

Nice

@Shadow-11158 11 ай бұрын

Nice

@jamestavake9726 11 ай бұрын

Really helpful video

@danejutzen1179 Жыл бұрын

what about torque specs? i cant seem to find them anywhere.

@stephenmulholland4868 4 ай бұрын

The 35mm axle nut is 235nm

@mattbeck1545 Жыл бұрын

That's living barry

@mattbeck1545 Жыл бұрын

Bet the midgies were bad nice spot

@marsu52 Жыл бұрын

Well done

@ILoveLSD13 Жыл бұрын

Do you put the smaller outer dust seal on, I can't see it and can't see it on a exploded diagram

@lloydiesgarage4214 Жыл бұрын

Yes mate 👍

@danieloliveira2223 Жыл бұрын

Basta soltar o pivô da bandeja inferior, a porca da ponta do eixo, dar uma girada na direção aí é só retirar o eixo e um toque retira com a tulipa, não precisa desmontar a suspensão toda

@Atozatozatoz Жыл бұрын

May I ask, when it's time to change these CV shafts, can we just change 1 side only (the side that needs changing) or it's best to change both sides at the same time? Thank you kindly in advance for all replies/feedback... Really appreciate it 🥰 Great & very informative video uploaded too... Keep it up 👏 🏆