What is the best way to get it off your hands after insulating pipes all night?
@remcobeekman43593 күн бұрын
Let It dry longer so it doesn't stick on your hands
@chris846624 күн бұрын
Ok, now how to make a p-trap
@longsleevethong145725 күн бұрын
Can you make custom sizes?
@alias9523 ай бұрын
Beser imer nur rund schneiden bei armaflex
@dardan10824 ай бұрын
It’s realy not recomanded to dry the glu like you do y’a have to let the glu dry by her self , if you blow on or if you shake it like you do to make air the pieces will not stick good. When you work armaflex you hav to take your time
@ArmacellMultiMedia3 ай бұрын
Thank you for your feedback. As you commented, we do not recommend to blow on an adhered seam. This might cause water molecules to stick onto the surface which can cause lack of adhesion strength. Waving the adhered seam on the other hand can speed up the applicaiton without causing any adhesion weakness.
@bettymelvin7495 ай бұрын
No information worthless video.
@ArmacellMultiMedia3 ай бұрын
Thank you for your feedback. This video is designed to highlight the critical steps in cutting ArmaFlex tubes correctly. Proper cutting ensures optimal insulation performance and longevity, preventing issues such as thermal bridging and condensation.
@Jacobs-pillow5 ай бұрын
Good skills
@ArmacellMultiMedia3 ай бұрын
Thank you for your feedback.
@phillipsin61028 ай бұрын
Good Job
@ArmacellMultiMedia3 ай бұрын
Thank you for your feedback.
@미스킴-y1q9 ай бұрын
Here is Korea I would like to purchase a knife. I would like to know the phone number of the Korean agency. thank you
@ArmacellMultiMedia3 ай бұрын
Thank you for your comment. You can ask your local Armacell Representative to direct you to the correct local distributor or please use the Armacell contact page: www.armacell.com/en-GB/contact-specialist. We will ensure you receive a timely response from the relevant Armacell expert.
@alias95210 ай бұрын
?😊
@alias95210 ай бұрын
Wizo schneiden si nicht andere zeite rund
@ArmacellMultiMedia3 ай бұрын
Vielen Dank für Ihr Feedback. Der Schnitt kann auch auf der anderen Seite vorgenommen werden, solange das Innere des Schlauchs nicht beschädigt wird.
@johnniebkid11 ай бұрын
I'm interested in the pen, and brushes you used. Can you tell me where to get them. I use Armacell constantly
@ArmacellMultiMedia3 ай бұрын
Thank you for your feedback. You can ask your wholesaler to get Armacell pen and brush.
@JohnnyBoBonny2 ай бұрын
@@ArmacellMultiMedia is it just a typical gel pen? silver gel?
@LuminairPrime Жыл бұрын
You should link to a printable template!
@ArmacellMultiMedia3 ай бұрын
Thank you for your comment. In the industry there are several pipe types for 90° Bends with smaller radiuses or bigger radiuses. On top of that woffer several insulation thicknesses and we have multilayer solutions where the total diameter changes. If these are combined together, there would be many templates only for one pipe diameter. Therefore, we recommend to create one template on the job-site and use it for your project.
@darrens1322 Жыл бұрын
Is that a bread knife? 🥸
@ArmacellMultiMedia Жыл бұрын
Thank you for your comment. We are using 3 different knives for different purposes. The long knife is mostly used for round cuts, incline cuts where more surface area is needed. Middle size knife is mostly for straight cuts in case stability is important, and small knife is for small surface areas like pipe cutouts etc.
@Lukas-vl4pj Жыл бұрын
Can you apply the adhesive when the armacell is already around the pipe? Will armaflex 520 destroy in example the Sanipex MT pipe?
@ArmacellMultiMedia Жыл бұрын
Thank you for your comment. The compatibility of the adhesives and the pipes should always be checked and confirmed. You can ask your local Armacell Representative to confirm if the adhesive is compatible.
@chrismartin9743 Жыл бұрын
If you use these Armacell adhesives on recycled Armacell foam will the foam still remain 100% recyclable?
@ArmacellMultiMedia Жыл бұрын
Thank you for your comment. In order to have the correct answer, it is important to know which FEF and adhesive are used during the application. We would recommend you to get in touch with your local Armacell Representative and give more information about the used products to have the correct answer.
@CHRIS3PHX Жыл бұрын
Put out 22 hours ago, I’ve been doing this for years lol
@Supernova66 Жыл бұрын
Me too but the boxes (especially the sheet boxes) are not as strong as they used to be. The cardboard is very thick and stong but the glue they use the last couple of years is not so good so they usually split open right away. I use Armacell 520 to reglue them but i hope someone at Armacell reads this so they can fix that in the factory. Mark van Utrecht Isolatie, The Netherlands
@ArmacellMultiMedia Жыл бұрын
Thank you for your comment. Tube cartons look more stable because during the work on site, not the whole tubes are taken out of the carton and used. Therefore, there are still materials inside and this creates more stability. However, sheet materials are mostly taken out of the carton competely.
@ArmacellMultiMedia Жыл бұрын
Thank you for your comment. It is good to see that professional people like you have already discovered the best practice years ago.
@ImportWade Жыл бұрын
Fantastic! Do you have part numbers / distributors fort he Armaflex knife kit here in Canada?
@ArmacellMultiMedia Жыл бұрын
Thank you for your comment. You can ask your local Armacell Representative to direct you to the correct local distributor.
@daytonbaker5494 Жыл бұрын
I work with the stuff constantly all you need is a Dexter rubber knife it's square and long for accurate cuts it's the perfect knife for this sort of work
@longsleevethong145725 күн бұрын
Can you make custom sizes?
@mmafinesse Жыл бұрын
Beautiful 👌
@chahatsharma22312 жыл бұрын
where can i find these rivets and riveting tool???
@chahatsharma2231 Жыл бұрын
@santoshjoshi5424 are bhai bhai bhai......🤣🤣🤣
@ABRARKHAN-pt1zq2 жыл бұрын
Dear sir, Why we have to overlap 50mm
@mdsultanmanjhar00073 жыл бұрын
Hello sir my name is md sultan my aluminum duck cladding fittar 6 yer experience in abu Dhabi uae
@integranddistributor58913 жыл бұрын
I wish I knew about these measuring devices years ago , we use a regular tape measure to find the hill and throat
@hichamhm23883 жыл бұрын
Very good work my Friend ric
@farhanauni64714 жыл бұрын
very nice
@joserocha73664 жыл бұрын
Good job guys do the 2dn part with the jakce
@joserocha73664 жыл бұрын
Wearing the mask because of the corona i know😂
@부들부들-c5k4 жыл бұрын
What is your pen?
@GeneralVol4234 жыл бұрын
Great work. The only problem i have with the video is it really dont transition to the real world. Real world very rarely will you be able to slide the armaflex down on the 45 like that. Should do a part 2 showing how to do it when you have a valve or a 45 elbow above the 45. So that people that are tring to get into the insulation trade can see a on the job situation.
@eastafrica79254 жыл бұрын
All the horizontal pipeline the end cap should be under the metal.
@hichamhm23884 жыл бұрын
Very good work my teacher rick👏👏
@JoseRamirez-rk7wn4 жыл бұрын
Good
@seaspidermariner91644 жыл бұрын
Good explanation
@mattheweveleigh63514 жыл бұрын
Where can I buy the miter chart you have?
@justiceson78064 жыл бұрын
Very good
@ArmacellMultiMedia4 жыл бұрын
Thanks
@joseyordyyordit28604 жыл бұрын
Muy bueno exlelente
@joseyordyyordit28604 жыл бұрын
Muy bueno pero seria mejor en español la traducion
@szabotamas41954 жыл бұрын
Hi! Where can i buy one?
@gymweeb92294 жыл бұрын
Hello, i wanted to know if armaflex still insulates if it is used inside a pipe instead of outside.
@mustang09094 жыл бұрын
very good
@ArmacellMultiMedia4 жыл бұрын
Thanks
@Worlberezka4 жыл бұрын
Nice
@ArmacellMultiMedia4 жыл бұрын
Thanks
@maheshmantri8534 жыл бұрын
Any Formula for making those Fish Structures Segments, Please share
@mikezuro14554 жыл бұрын
I’m impressed.
@ArmacellMultiMedia4 жыл бұрын
Thank you
@hachinz62264 жыл бұрын
Is it foamglass? Looks like it.
@gomesfilmador4 жыл бұрын
Me chamo luiz André Gomes, isolador termico trabalho com o Sr. Martins ex socio da empresa Mac engenharia localizado em salvador na Bahia, em particular discordo dessa apresentação, onde o apresentador faz um molde encaixando na conexão deixando vaco de ar dentro onde daqui um tempo vai acumular água... Obrigado
@yomofo1014 жыл бұрын
Great installation videos. Do you know the make/model of the technical paint marker being used, please?