bambo laps shit

expectations vs reality, it's 2024 and you still trying to get that oil Pan out right ? 😂😂

Great video & Informative!! Thank you

So I have the tcm grounded. But still having the same problem

I didn’t think that the engine “curtain” or backside heat shield dampener.

Hilo bro Did acadia 2010 have orfice tube forfront? Thank you

I love the brutal honesty lmao ima go do mine now 👍

This guy is speaking through his butt hole.

this vid just ruined my day

Thank you so much😄

Thank you posting!

Hi I hope you found the solution by now, for me just connecting both my printer and the Bambu Studio to the same Bambu lab account automatically connected it to the printer.

Gunna git your mama some soap to wash yer mouth out.

I bought champions

Exact same thing happened to me for an evap swap. At least now I know what happened. Thanks for the vid!

Had a small bottle cap taped onto the brake pedal to hit the sensor for a while now and it was getting annoying. Kept slipping off and stuff then came across your vid. You're the man bro! Fixed in about 20 seconds. thank you!!!!

Thx man

For anyone watching this now, the "missing" gasket he was referring to is an o-ring already attached to the black plastic hose inlet. I thought the same thing when I opened the thermostat box and didn't see a new gasket. Just clean up the back side of the plastic tube and o-ring.

This worked for me! Thanks!

The screwdriver will tell you if you have a warped rotor, a dial indicator will only tell you how many 1000ths it's out! Who cares how many 1000ths??? WARPED IS WARPED!!

Junk money. Are u even a red seal technician or just some fixer upper guy. I wouldn't even do it for 200 k a year

Tried this, the QR page on the screen DOES NOT display a pin code, it says login to the app. The app then says to login with a phone number and has a Get Access Code link which does NOTHING.

This is what worked for me. Turn on LAN only mode in the printer and keep that screen up for the access code. then in bambu studio underneath where it says bind with PIN code, the printer should appear after a minute. You will have to plug in the access code that the printer is showing you. I just figured this out and my print is looking good so far.

This is the best most useful video I have ever watched I am subscribed!

How do you get the cover off???

What would I do different if I was taking everything. Engine ,trans and suspension.

You have to leave it on the LAN code

I was pumped to do my timing chain until i saw this video...people say its just as easy doing the water pump but on a 1994 4.9L all you have to do is remove the battery and coolant reservoir to have enough room to remove the water pump....too bad I order the parts before the video.

Hi🖐, i got a question, does a warped brake rotor can cause a bad rear wheels alignment on a rigid rear drivetrain ?

Mine went on my 2017 Colorado at 120,000. Now it has 238,100 miles and it went again.

Good video

You sound like you just started swearing for the first time

Thanks for ur video you have made my life easier i had same issue thank you somuch

Rather then using the pin code you can make sure you are logged in on bambu studio with the same account that you use for the printer.

Thank you brother!! Awesome video!!!

Could have been one minute--just loosen that one bolt on the cover and you can pull it back enough to see the belt.

The perfect video does not exi.... yes it does exist now. Wiring my buddy's f250 super duty and man, short, sweet and to the point! Bravo you did us justice my man!

Getting ready to start on a fan replacement and Im hoping this video saves me some time.

I'm guessing this is how you get to the fan for replacement as well.

Have you done a frount one yet?

You 100% right, stupid shit. Why do these f'ing stupid ass developers hide shit like this they know we will need ...WTF! Good job, I would have never figured that out, thank you and YT. What the F is wrong with using an IP like normal smart people do.

My diagnostic tool doesn't do anything it does not even come on it works on car power

Nice nails, not working on x1c

This made me feel better about fixing my hose. Thank you for your video!

Thank you so much for this I didn’t know how to get a pin

Thanks for the tips. Very similar to my 03 GS430 except my battery is on passenger side.

I have a 2012 with the exact same interior layout and I need to remove ignition switch assembly. Do you have any suggestions or recommendations for removing that?

This video was absolutely pointless, you showed nothing on how to do anything all you did was talk lol! Nobody wants to hear you talk common sense things, if you're going to make a mechanical video, then you have to show actual instructional work

I'm on Hondas all my life and I can tell that you've never worked on a Honda just by the simple fact that a 3.2 is nothing like the 3.0

Where does the orfice tube filter go for the rear