Wood_Works

Пікірлер

@sigung01 14 күн бұрын

This is 3 minutes of my life I'll never get back. How to spend an hour to make two jigs to enable the making of the world's worst joint.

@woodworkswala 5 күн бұрын

get lost

@Blankholes Ай бұрын

So you go ahead and make intentional mistakes just to show this overly exaggerated crap. 🥱

@gert-jantencate8472 Ай бұрын

A lot of work for two planks. But….the result is good. 👍🏻

@woodworkswala Ай бұрын

Yes, thanks

@Ghostreaper-dr7fx Ай бұрын

Nah. I would never buy this. 😂

@woodworkswala Ай бұрын

@onemoresob1022 Ай бұрын

More glue maybe?

@woodworkswala 5 күн бұрын

to your ass

@CabdulaahiCaleey Ай бұрын

Somali2 ok

@hamp7803 Ай бұрын

This isn't amazing!!! If the ends are not cut straight, then no matter the brace, it will not align properly. Don't get me wrong. It's a nice DIY project, BUT it isn't amazing.

@woodworkswala Ай бұрын

but we can improve it

@vsvickysarkar3689 Ай бұрын

😂😂😂।।ooo bc।ab ye vhi sikhna tha

@woodworkswala Ай бұрын

hahaha F O

@vsvickysarkar3689 Ай бұрын

@@woodworkswala yeahh।।।same 2 you dr

@mewokidz Ай бұрын

@remy310572 Ай бұрын

👍 Nice

@AllenCash-jh9et Ай бұрын

What he is trying to say is to only push the file . Back stroke on the file will not cut...just dules the file.

@woodworkswala Ай бұрын

yeah of course

@Gowood2020-ne6rx Ай бұрын

Good one

@romescarlossilva1015 Ай бұрын

NÃO É ASSIM NÃO ANIMAL! LIMAR É SÓ PRA FRENTE!

@woodworkswala Ай бұрын

yeah👍

@tanvermalik 2 ай бұрын

🎉🎉🎉🎉😮

@BeenyMughal 2 ай бұрын

luckiest work ever

@mobimughal707 2 ай бұрын

Amazing skills

@mobimughal707 2 ай бұрын

THAT was amazing?

@marishmelnickis4119 3 ай бұрын

ЕЛЕМЕНТАРНО ВАТСОН ,СЕРТИНЬЮ ДИРЕЙТИНЬЮ ПЕДРО ❤🧷

@learnquraanjeh4690 5 ай бұрын

kzbin.infoJjLSBYabXYs?si=QUcNfvXgRIuFcc6b

@Khmu2449 5 ай бұрын

สะบายดี❤❤❤❤🎉🎉🎉🎉🎉

@user-hp8mz1zl5t 8 ай бұрын

Угольник п...ц..Нах такого мастера😢

@zaidbutt4733 8 ай бұрын

Good Work❤

@woodworkswala 8 ай бұрын

Thank you! 😊

@michaelwingen673 8 ай бұрын

Mit absaugung wird das Ergebnis besser und der Lärm weniger!

@woodworkswala 8 ай бұрын

yeah dear

@user-ze2ni9bz9m 9 ай бұрын

wawa Kya diesgin ha

@user-hf1hw7yj5t 9 ай бұрын

Для этого есть шурупы. Хотя....

@woodworkswala 9 ай бұрын

yes obviously my respect man

@BeenyMughal 9 ай бұрын

❤❤

@zaidbutt4733 9 ай бұрын

Good Work❤

@zaidbutt4733 9 ай бұрын

❤❤❤

@senhalp5724 9 ай бұрын

Please replace the cable on the router

@woodworkswala 9 ай бұрын

yeah it will be soon

@ikallaroaster 9 ай бұрын

Ye viral hogi sahi mein 😊😊

@woodworkswala 9 ай бұрын

Shukrea apka pyar ka mohtrum

@jbsimmons54 10 ай бұрын

Your not using a jointer to square stock correctly. You must not drag wood backwards over the knives. After making a few forward passes on one edge only, that edge is placed next to the fence and a second side is squared. Then place that just squared side against the fence and do the 3rd side, and then usung the 3rd, then the 4th. Your stock is now square. This assumes none of the sides is square to start with, unless you rip it on the table saw first and then the jointer to smooth out the rough saw marks. If you have a wide piece wuder than the jointer table, locate a power planer to do thos two sides. The planer will also square stock, but fot some thin and wide dimensions a planer/jointer combo is best.

@woodworkswala 10 ай бұрын

Thanku for your suggestions my dear i will be careful next

@mikebythesea45 11 ай бұрын

I have a track saw but this is similar. The blade is easily heated if the heavy motor hangs off the unsupported end and it side loads. Reposition the ‘track’ so the motor stays on the door. Let the cut end fall off.

@woodworkswala 11 ай бұрын

yeah you are absolutely riight my respective subscriber