I replace a head gasket and water pump and now it doesn't have compression do you know why ? It's. 2006 chrysler 300 2.7l

Im watchingg thizz carefully. I'm gonna be doing my mom's car and I need. To maske sure I do this job perfect

The best spark plugs for 07 Chrysler 300 2.7, thanks

Way to torqued a little WD 40 works that way you don't damage cylinder head

It won't come out because it's de threading

I would go ahead and replace everything under that intake manifold might as well it's all remover and also removing the window cowl easy pizzy up and easy for EGR valve, tube, PCV valve

Magnets are awesome

I just realized mines was too lol

PERFECT tutorial

There are two ring gaskets when buying the plenum gasket... i know one goes on the egr valve tube that connects to the plenum but what about the other ring where does that one go? If u can help I would really appreciate it sir thanks

2:50 it’s backwards .. you want to start loosening your bolts evenly starting from the inside working your way to the outer bolts .if you start on the corner the corners lift which will crack your manifold . If you start in the center the corners are held tightly and once you loosen the corners it will lift evenly with no damage .

Chignon 👍

I wish you would’ve counted those

Muy bien Gracias por compartir Bendiciones Adelante.

Great video, thanks for uploading it. Very helpful

I changed the spark plugs, load coil, and fuel injector but still getting a misfire at the same location! What else could it be?

Whats the name of the tubing that is behind the plenum cover? Mine broke but idk the name of it

It’s amazing how easy these cars are to work on

Never take your plugs out like this dude

Aaannd Action. 😂

What causes oil to build up on the top back end of the plenum? The part that curves into my throttle body is oily

5:50 im on the floor laughing ....He is the definition of shade tree.

Oh my god, thank you sir

Onde e isso ?

Where's the pcv valve on this car, please help

Worst engines ever

Junk motor

Hey I have 06 dodge magnum I have code p0301 clynider 1 misfire 3.5liter v6

The best part was when the camera guy said "action" in the beginning of the video

Its alot easier to change plugs on a 2.7 intrepid. They changed the intake.

I’d like to know the purpose of that foam under the plenum. Mine was so bad that it was crumbling. not even foam anymore it was just mush like a grease.

Thank you for your help! Saved me $500!! (Needed to replace the EGR)

thank you very much sir

Thank you so much hopefully this saves me $ 265 tomorrow.

What would happen if I did this job without disconnecting the battery because now my car is idling high

Thanks for the video. How much more work is it to replace the lower intake manifold gaskets?

Hi I am having problems with the gasket leaking. I just bought a brand new one looked under the hood and it was leaking. Now my car doesn't crank. It make a weird noise when I try.

My chech engine came on, the codr stated misfire from cylinder 3. I've changed my cylinder 3 ignition coil out and replaced spark plug. When i started car it seem like it got worst, this time it even started to make backfire noise.

There is no sequence to loosening the intake bolts. Only during tightening.

great video..thanks

Thanks. I used this along with another video to change out one of my fuel injectors.

tengo 2009 300lx Chrysler a aveses no prende si tiene corriente al

did u have to remove the Neg. cable?

good night my is name ronald brown jr fix not work 2006 chryster300 radiator and thermoster water still hot light

Very good video. Thanks!

It's BS too about how you have to check the Transmission fluid!!!

Wish I never purchased this car! Chrysler you knew what you were doing, lining the pockets of all the dealers!!! NEVER AGAIN!

Why is he being so rough with the ratchet tho??

Great video! Saved over $250 in labor....

How do those damn wire connectors on the throttle body work