Thank you, straight to the point and I'm not stupid anymore!!
@wingtang4234Ай бұрын
Hi, nice job. May I ask you a question? Do you happens to know where the PDC buzzer is located?
@vinmon1234Ай бұрын
No I'm sorry contact partworks and they may be able to help
@wingtang4234Ай бұрын
@@vinmon1234 Thank you for the direction. I have sent them a message now.
@adamhope9117Ай бұрын
Why wouldn't you clean out the bottom of the bowl? Isn't that where the water sensor is?
@vinmon1234Ай бұрын
Yes I done it of screen
@DAVESPORTCARSАй бұрын
Thanks
@ianyates98812 ай бұрын
Hey there...do you know the part number of thr blue screw anchors
@vinmon12342 ай бұрын
No sorry I repair everything
@mattymatt20272 ай бұрын
nice find
@c1nicolei2 ай бұрын
I had covered paired wire that looked the same, thank you for your help. Stripped and now I know silver + copper negative. 😊
@billyjenkins18063 ай бұрын
Hi. You wouldn't still have this adapter to sell would you?
@vinmon12343 ай бұрын
no sorry I made them
@philmissen23653 ай бұрын
Good job, Cheers
@CROFTY714 ай бұрын
He probably knows now that he can pull his coolant spout out for that side. Do what he done but for the left side
@vinmon12344 ай бұрын
hand fits in the left side without removing anything
@lilaw59504 ай бұрын
Cheers mate, hardest bit is getting the nut done up flush haha.
@EastAvenueWoodWorks5 ай бұрын
5 years later, 1st time changing AP racing pads,, had me stumped. Very first video to come up on the tube,, thanks for posting.
@KanemNeal6 ай бұрын
Bro thank you for real
@peter37917 ай бұрын
super gemacht !! +++
@andrewgrano9757 ай бұрын
Legend!
@MuhammadSulmanHaider7 ай бұрын
Am changing my first filter
@albrigodaniel7 ай бұрын
Thank you, I fixed it myself and saved money because of your video
@jiehadmallum71278 ай бұрын
Great clear video and sound for a DIY job....Thanks
@gearswitch56928 ай бұрын
Did you only have to spray down the central tube that the selector knob attaches to or did you also have to clean the contacts at the back of the switch. My lights are very dim. Thank you!
@vinmon12347 ай бұрын
you can do both
@shoaibbaig31558 ай бұрын
I have the same wire but I don't know how to connect the wire in rca plug in screw and in skin please tell me?
@vinmon12347 ай бұрын
plain in middle
@andrewwhitehead57928 ай бұрын
Yea nah all wrong mate
@scottydees27488 ай бұрын
Champion mate. Cheers.
@noes.castillol.49359 ай бұрын
WOW, EXCELLENT VIDEO, THANK YOU VERY MUCH.
@simontoppin68449 ай бұрын
Great video. Simple to understand and well explained
@SWERVNKOLIDE10 ай бұрын
WRONG
@ramonmichaud300411 ай бұрын
I can understand building something with a certain life span for comercial reasons ,but not at the risk of safety.
@Chris-td4yd Жыл бұрын
Thanks 👍
@Chris-td4yd Жыл бұрын
Cheers 👍
@luckylotus11 Жыл бұрын
Thanks
@schwinnbiking Жыл бұрын
where did you find the info to make the centre adjustment cutout? Looks like cardboard, did it work?
@darkknight6921 Жыл бұрын
You’re awesome, thank you!
@charlielogik Жыл бұрын
Thanks Legend!
@PrettyGreenMonk Жыл бұрын
Nice easy one
@coolinmac Жыл бұрын
Fair play but I’ve never been so nervous for someone with a soldering iron in their hand
@harrik4292 Жыл бұрын
I'll have to point out that if you have factory sport seats you will have to loose the passenger front seat bolts to be able to jiggle the console out. Sport seats are wider than standard and there just isn't enough space to get console out...
@tysontom1 Жыл бұрын
Legend! First time doing it, was easy explained, it ls really that simple to do! Cheers
@10223220 Жыл бұрын
It was just what i was needing thanks👍
@fifthdimension1984 Жыл бұрын
Thats very, very interesting. What idiot designer specifies a plastic flue??? That would have to be the height of design stupidity. I have an internal MPS He30i of a similar vintage in my roof cavity so as a DIY person that I am will check this out. My guess is that the flue was made plastic because (apart from a few$$cheaper) thru the "efficiency" design meant that the flue gases were cooler than other gas heaters. Flue gases generally are very hot, hence requiring metal flue construction, but the MPS series was supposedly more efficient in retaining heat - less loss thru the flue- meaning lower exit temperature meaning no need for metal and ok for the cheaper plastic version. My opinion ( as a chemical engineer myself) is that this was a foolhardy commercial decision to go with a plastic flue because the RISK of failure ( as clearly seen here) is that carbon monoxide will go directly back into the unit and into the ducts. Its quite unbelievable actually. If Brivis is keeping quiet on the matter , the issue could legally explode in their face. Some years ago there was an issue with certain wall heaters( Vulcan I think) where it was deemed too much heat could transfer internally to the plaster board at the back of the heater and posed a potential fire risk. Vulcan issued a statement to all owners to contact them and they came to your home, removed the wall heater and fitted a metal plate as a protection. Frankly, Brivis should do the same thing. Issue a warning notice to owners and come out and replace the plastic flue with a metal one.
@mikewebster9121 Жыл бұрын
Phil Collins demonstrates how to do brakes. 😉
@digitalleverage Жыл бұрын
Thank you!! 🙏🏽🙏🏽 Not stupid at all! I have silver & copper wires and couldn’t tell what’s what.
@vinmon12347 ай бұрын
silver =- negative
@suckafish2k92 ай бұрын
So which is it bc what you say in your video contradicts what you wrote in this response smh
@AdamKostanski-dd4zq Жыл бұрын
Thanks mate good job
@CephalusCapone Жыл бұрын
Thank you sir
@battlehrfred Жыл бұрын
opppps Mate!! "never"use a tissue. if the tiny piece of tissue fall in that master cylinder,it can cause you nightmares. just go to a "dollar" store and have some few plastic syringes and suck it out and dispose the old plastic syringe...not worth the nightmare it can cause. saw this happen before and cause lots of Dollars and issues with brakes being stuck because of this ordeal. I personally will only use syringe or Turkey Basker and the dispose after use. ty sir Cheers great video
@christopherfaeth8047 Жыл бұрын
What bulb is behind the right lcd screen? I need that bulb's part number
@vinmon1234 Жыл бұрын
Take the old one to a spears parts outlet
@caffecapri Жыл бұрын
Thank you. Couldn't figure out the last clip when door panel was already off. Sliding it backwards while prying. Genius.
@3067jon5 ай бұрын
same my man, all other videos have a very different way of doing it!
@fireblade8905 Жыл бұрын
Copper grease should be applied to the back of the pads to prevent the pistons sticking to the pads.
@jameslukrow16252 жыл бұрын
You’re stupid how can we understand you way
@PracticalCat2 жыл бұрын
I have a He30e V3 from 2003. Still running but the flue terminal is coated in soot. Its the model that followed the one in your video. It has the plastic flue fan housing and pvc dwv internal vent. I wonder if it also has the plastic HX box and if the soot is at all related to a crack.
@vinmon12342 жыл бұрын
Yes this has a plastic inside swell as far as sort there may be another problem
@garage_in_la2 жыл бұрын
Спасибо вы очень помогли!)Привет из солнечной Калифорнии🤝