Hello, please contact our export department for more information on how we can get our products to you: [email protected]

Hello, please contact our export department for more information on how we can get our products to you: [email protected]

Hello, please contact our export department by email for more information on how we can get our products to you: [email protected]

Hello, please contact our export department by email for more information on how we can get our products to you: [email protected]

Hello, please contact our export department for more information on how we can get our products to you: [email protected]

Hello, please contact our export department for more information on how we can get our products to you: [email protected]

Hello, please contact our export department for more information on how we can get our products to you: [email protected]

@@FerncoLtd thanks

Yes boiler pipes will be fine, it can work up 218 degrees. As long as its not being used as the primary connection between the 3/4" and 1" pipe it will be fine, its just for repair work not actually connecting parts. And yes it will be fine round a nut if applied properly.

Please email [email protected] and we can get accurate costs to you by email. Thanks

@@FerncoLtd looking for 10" & 12" parts

@@FerncoLtd u guys have a part # cv 10

Please email [email protected] if you're based in the UK or [email protected] if you're outside of the UK, and we can get accurate costs to you over email. Thanks

​@@FerncoLtdtry to email you but didn't get to the you.

@@chiangmaimeatjerky5963 Hello, please try copying the email below to contact our export department by email: [email protected]

Hello Niko, please contact our export department by email for more information on how we can get our products to you: [email protected]

Hello Muhammad, please contact our export department for more information on how we can get our products to you: [email protected]

Hello Yogesh, please contact our export department for more information on how we can get our products to you: [email protected]

Please email [email protected], so that we can support you with this product in India.

The NRV is a push fit application, no tools or fixings needed; simply apply a small amount of lubrication or water and push directly into the bore of the inlet.

@@FerncoLtd i have pushed it without water anda fixing screw. I hope it will works fine.

How did it work? Any issues 3 years later?​@@apfelbaum867

Hi, we have a newer video here showing installation of plastic: kzbin.info/www/bejne/lWmte4mIl8yjlbs

Our local water company has stated that the damaged pipe must be replaced with vitrified clay, so regardless of more modern products, there is always a need for the older materials.

Please email [email protected]. Thanks

Thanks for the feedback. We don't sell the cutters unfortunately, we just used it for demo purposes.

Thanks for your interest, if you are in the UK then please email [email protected], if you are outside of the UK please email [email protected]

@@flexsealmarketing5463 im from Malaysia

@@thiagumalaysiathiagu9013 please email [email protected]. Thanks

@@FerncoLtd i emai ready.pls Check

It is important to leave a small gap to allow for possible ground settlement which can cause minor movements in the joint. If the clay pipe ends butt up against each other and ground settlement causes joints to move, this could cause either pipe section to crack. This is also a reason why it is important to use shear banded couplings to reduce the risk of movement in the joint.

Hi Stanley, the pipe is DN150 vitrified clay with an outside diameter of 188mm

Hello Vanya, yes we do. Our head office is in Davison, Michigan under the brand Fernco. Feel free to reach out to them and they will be able to point you in the right direction for local stockists www.fernco.com/

Cut and replace the section of pipe covered by the wrap. However, we'd always like you to reach out to us with any technical issues or installation advice required.

For pipes with different diameters, we have the following products available... Adaptor Couplings kzbin.info/www/bejne/apfNkpeXf9KVpJY Standard Couplings with a Bushes kzbin.info/www/bejne/eGfdpXRunbZ9qsk

Hi Lewis, the step is on the outside of the pipe to allow for the different material outside diameters. The pipe bore's share the same nominal ID and line up centrally to each other with absolutely no lip inside the pipe.

Hi, the substance is designed to be used within drainage systems however it is completely soluble and non-toxic so we can't see any issues arising. However, we could not guarantee this as it's never been tested within vehicle cooling systems.

the gap is to allow for any potential movement around the assembly, if the pipes are butt up to each other this movement could cause damage or breakage to the pipe if made from clay or other brittle materials

Hi, thanks for you enquiry. The ends of the cut pipes don't need sealing individually. Connecting the two pipes together using a Flexseal Standard Coupling, as shown above will be sufficient.