That was perfect explanation thank u

This is a terrible Video. This guy IS NOT IBE TOBLEARN FROM.

SorrycTo Satly This. THE VERY Fact you Believed that you could use a hole saw Meant for wooden applications on stucco exterior Brightly shows you are a very Rookie Diy'er.

My 2000 will not drain

Great! Thanks

Two nuts put on, if you didn't screw up the bolt threads, I think could do a similar job if your only way to get to the store is half apart in front of you.😂 but like you so clearly and well spoke,,,patience!!!

Well done! The way you narrate, keying constantly on patience and not just bam, bam, is so important. I see little of this from most professional KZbinrs.💯💯

This is wonderful! Thanks a million for showing step by step w details & narration! My husband is about to replace ours too bc the serpentine belt keeps getting shaved down & off track after replacing it and our car has been losing power & power steering. Thank God for AAA towing the car back home a few times! Project Harmonic Balancer is commencing in our driveway tomorrow morning!

You made a truly good video here and you should receive royalties from the tool manufacturer in my opinion. I haven't gotten to the point yet of breaking any of the 3 stuck bolts in my 1995 351 truck, but I'm so certain it's going to happen. And after watching your video a few weeks ago I went ahead and bought a tool I believe to be at least identical to yours in preparation. I currently have eleven 9th gen trucks with one being a 93 Bronco. I'm retired on disability and hope to end up with a couple reliable drivers and make a small profit off the rest to supplement the income our current government is cutting in leaps and bounds in order to buy and support the new voters they've opened our border for ! Thank you much for your time and effort in sharing this information. Having spent half my life as a Die Maker Machinist and being no stranger to broken bolts, I can see this tool having a special place in my arsenal.

Awesomeness

Thank you so much for making these videos!

I'm about to do this

Can you tell me if the generator is vented out of the top of the RV?

AWESOME! WORKS GREAT!

Can you tell me if replacing the chassis batteries would cause the check engine light to come on? It wasn’t on until we replaced them.

Wondering exactly where below is to get that part number to buy one of these instruments on Amazon ? Ford could have done far better with water pump bolts as could have Toyota . I'm currently changing the water pump on my one of eleven 9th gen trucks . These were the last of the true all Ford trucks . The 2 things I like the least is the water pump bolts and the fuel line disconnects . I do appreciate your video and will figure out finding the tool as I'm a tool nut . I'm pretty certain I have 2 bolts the outer 2 from side to side that feel as if someone used green loctite on them. I have 45 years experience in rusty bolts, (and many techniques in removal of such bolts), over 30 years working with plastic injection molds and stamping dies with a heavy background of broken bolts and water lines and all sorts of different ways of dealing with such pains . I'm now a 60 year old cripple loaded with physical pain and am always willing to try new methods to make things easier . So thanks again for your time and effort with the video. It's very well done.

So, I recently bought a SM-P355M and have the same problem... I'd like an upgrade tho so would samsung swap and or trade.?

reat filming!

DO NOT install a brass drain plug in the aluminum tank of an Atwood water heater! It will set up a galvanic cell and corrode, welding itself to the tank and you will then damage the tank trying to remove it!

Do you have to disconnect the electrical when manually retracting the slide?

Thanks that was helpful! I wonder if you have other DIY Alfa videos? I have a 2004.

You saved me a saw! 😂

Rip your still helping me in heaven thank you 🙏

Thank you soooooooooo much for sharing that information. My slideouts aren't working now.

He looks like my dad from the side!

You don't need that tool for the ford stud bolts, you can just use two nuts jammed together on the threaded stud, and work it back and forth, after tapping with a hammer to loosen the rust and best to heat it up if no wires to melt, then work it back and forth to break apart the rust. You should not have cut it off, that achieved nothing.

GOOO trump

thx

great job

i love u

I have a 2006 Airolite Travel trailer. I am a single 67 year young grandmother, having to learn how to dob alot of new things on my on. With a fixed income it's not in my budget to hire someone. I don't have a l9t of tools and when it comes to measuring I make a lot of mistakes. Hopefully i will figure out how to install s window air-conditioner and pray it turns out ok

Can’t wait to try it, ThankX! I’m also going to use rubbing alcohol as a final cleaning to let dry before using the . BTW some nail polish is watered down, look at the bottle ingredients before buying. I did the math and nail polish is comparable in price to buy a large gallon of it, considering how much you get. So the nail polish purchase isn’t a bad idea if you don’t need a gallon of it. Take care.

I really enjoy how he just gets after.It explains what we need to know nothing more. How to do a timing belt under 10 minutes?

very helpful and easy. thank you for helping others...

It would have been so much easier and faster to remove the compressor from the bottom and not remove all that other shit

So thankful he shared his knowledge and kindness!!!

Thank you so very very much. Sharing wisdom is a lovely gift. !!!🙏🏻🙏🏻🙏🏻🇺🇸🇺🇸🇺🇸

You can get to the belt from the wheel well too it’s much easier

Use drywall anchors as well. The big ones allow a small footprint to be used between 2 peices of wood or none if you do it right

Love it!

I am SO SORRY for your loss! What a helpful video he has made to help others. I am sure he will be missed!

only thing i would have added is an outside support post/pole good video thanks 🤠

Turned white how to fix?

This is such good wisdom for a lot of people who grew up without a Dad to show them these things!

Perfect pat and pend that adapter

Thank you sweet angel 2024 and still a needed video

Just found one for $20 at a garage sale. Had to get. A new belt for the power head but it’s good to go.

Will the generator shut down if the system is charged automatically?

I’m doing the same job on my 96 Bronco 5.8L. In my case the head of the bolt snapped off. I removed the water pump, leaving the snapped off bolt. No threads are exposed. Do you feel like this tool would still work with no head or threads exposed? Thanks

We have a Dometic vent fan 4100 model. Lift arm is plastic and broken of course. Can we replace it with a metal arm or are we just screwed by Dometic. Cannot find a replacement part online. Next stop Camper World 😮.