Can anyone tell me part no of 4 pin plug that was used I have purchased a 4 pin but didn’t work I would like to try exact one in video
@reviewcity317624 күн бұрын
thanks for watching !
@HDsharp7 ай бұрын
These scooters are not good for usage every day, the suspension on it is not good enough for every day usage, it's really bad for your knees. Unless you're not going more than a mile to the shops daily then it's fine, any further it's bad for your knees.
@candylps41798 ай бұрын
How do you change the cotton stick?????
@ErrollJones-s6d10 ай бұрын
Fantastic video but what did you mean by reverse the process. Can you please explain that in layman terms not in technical terms please 😅
@wiktormilka193311 ай бұрын
How change from kmh to mph??
@Boatperson Жыл бұрын
Product is a piece of crap don’t buy it!!!!!
@AleviStylez92 Жыл бұрын
Can you tell me in what order and colours the 4 pins come. Which of the 6 have to be picked up?
@ch2o2 Жыл бұрын
yes yes, when it started to get interesting, the camera stopped working :D ....but well, "error 40" is indeed a fault with the brake lever and fixing it can be a bit tricky (if it's not should be a simple contact error or a broken cable). The continuously adjustable braking effect is achieved with a "linear Hall sensor" (type: 49E 0028G), which was set between 2 magnets. Depending on how close they come to the sensor, its output voltage changes and regulates the braking effect. The whole thing is a bit cheaply constructed. For example, all three legs of my scooter's sensor were sheared off by the constant mechanical shocks and I had to solder new legs in a rather difficult operation and then cast the entire structure in synthetic resin (to prevent renewed damage). The assembly of the part is a bit tricky, because you always have to pay attention to the spring. After about 10 minutes of swearing, I succeeded and everything works like new again. If you're lucky, it's just a simple contact problem, if not, you need to be skilled.
@OlegPetrenko-go4kj Жыл бұрын
steam is not coming out after 2 month of usage, need to get a new one
@Aman.4578 Жыл бұрын
Really ? Am about to buy it 😮
@lashaburdzenidze2845 Жыл бұрын
hi, my idrive has long plug and its not available to buy can i change cables for little plug ? i think its the same cable
@reviewcity3176 Жыл бұрын
Exactly, you can use the instructions on this video
@davidlee4417 Жыл бұрын
Thanks for the video. Will the sensors and auto hold still work if you just connect the 4 wires? I don't mind if the senor on/off button itself doesn't work.
@reviewcity3176 Жыл бұрын
Hi, yes, sensors and auto hold all work fine.
@yvonnebrimpong6982 Жыл бұрын
Mine no steam coming out had it for a year
@kristinayates1 Жыл бұрын
Just bought,one off Amazon and no steam
@kristinayates1 Жыл бұрын
I didn't realise you have to charge it for two hours before it works. From the video it looks like it just plugs in like a kettle.
@luisalfredoreyesdeleon7479 Жыл бұрын
Can you share Wire setup 🙏 pls
@reviewcity3176 Жыл бұрын
Hey Luis, sorry man, I've sold the car a while back and don't really remember the full wiring setup any more. If you post your video and tag me and I'll try to help. It was pretty easy, even with trial and error I don't think it will take yiu more then an hour.
@lookinfor785722 жыл бұрын
Will the 2013 3 series media remote work on the 5 series 10 pin board. Can the operation be completed similar to how you did in this video? Just connect the 10 pin board to the four pins of the 3 series media controller? If so what would be my configuration to line up the equivalent pins?
@AntonioPerez-wr2bv2 жыл бұрын
Se puede cambiar gatillo por freno
@garikainyoni12 жыл бұрын
How does 1 remove the glue without damaging the assembly because you skipped that part
@reviewcity31762 жыл бұрын
Hey, apply heat towards the glue. Heat gun preferable. But a 2kw heater, or hairdryer will do just be slower and more awkward. Best of luck. Thanks.
@garikainyoni12 жыл бұрын
@@reviewcity3176 Thanks I’ve got a heat gun let me give it a try
@Denchik_vzm2 жыл бұрын
And I didn't understand what the repair was? Did you just reconnect the brake connector?
@GameFlashStudio2 жыл бұрын
hi my friend! i have problem with new scooter we bought to weeks ago and 2. run and now 4. run turn off when battery is 50%-40% and show for us is battery is 0%,but later again turn on with same battery status (40-50%).What problem?
@SamieMiah2 жыл бұрын
Hi Adam, sorry I'm not sure of your problem.
@phester282 жыл бұрын
most likely the bms protecting the battery. I have taken my battery apart and it had a low voltage on one cell. I now charge on my imax b6 charger with 2 charge cables. 6s and 4s separately and it keeps the battery in perfect balance
@edgarscepuris72432 жыл бұрын
Hi. I'm confused about part numbers? Or I can fitted any 4 pin controller who have Navi button? For yours 4 pin controller is 9253944. And there is many more 4 pin controllers with Navi buttons 9267955? Thanks 👍
@reviewcity31762 жыл бұрын
Great question, not sure of the answer. Please share your results if you tried other models. Thanks.
@darekh674610 ай бұрын
Just tried with the 9286699, doesn’t work at all or I bought faulty one from eBay 😅, I’m getting one from video now, we’ll see
@marianmafiotu200521 күн бұрын
@@darekh6746did it work ?
@darekh674620 күн бұрын
@@marianmafiotu2005 yes, i bought the same as on the video
@docwill59722 жыл бұрын
I can’t get the sides apart with nails or flathead.
@reviewcity31762 жыл бұрын
Hey doc, sorry havent checked up on this account in a long time. Hope you got on ok.
@docwill59722 жыл бұрын
@@reviewcity3176 I was an it actually worked in the long run. Thank you.
@maxwellrigs2 жыл бұрын
Good to know that it can be done but not clear on the wire mapping.
@reviewcity31762 жыл бұрын
Apologies for that. I've stopped the videos now, never really got good at it. 😂
@bilalali78002 жыл бұрын
Hey bro, a bit confused with some of the steps, is there a way to contact you and show you my setup that you can help with?
@michelilunga95932 жыл бұрын
My f10 idrive keeps displaying German language and doesn't go into menus for different functions. I watched your video and liked it. Is it something you can help? Michel
@reviewcity31762 жыл бұрын
Hey Michael, sorry, haven't monitored this youtube account in a long time. Hope you got on OK.
@the1bud2 жыл бұрын
My inside camera won't show color. Is there a setting I should use.
@feeif56792 жыл бұрын
To fix brake y have to remote the brake to dissamble it , pay attention to the mechanic spring inside y ll have three pin which make short circuit then y have to add a bit of tin on each pin and assemble again the error 40 ll be fixed
@Boooby082 жыл бұрын
Didn't work for me either..
@timharris19352 жыл бұрын
Found error 43 solution! Firstly thanks for this great video! It got me started fixing a problem I had. The "Kugoo Kirin S1" seems to be exactly the same scooter as the "i-bike mono jet" or "ibike mono jet" which is released in Italy and sold, amongst other places over Amazon. (Deliberately adding this info, perhaps change the title of your video as it will help ibike users too, like it helped me!) Error 43 is an error in one of the 5 connections from the top display down to the Controller for the DC brushless motor. I fixed a cable break in a broken unit i bought and kept getting the error, so I took a second unit i have that is fault free and swapped out part for part to verify the parts. (And thank you again this video helped a lot!) I noticed that the connector from the controller to the cable that runs up its quite cheap.. You push it in and very easily 1 of the 5 pins on either side of the clip pushes backwards making 1 or more connections to either not connect or connect only partially. Easy fix.. Push cables into the plug fold.. Same on other end.. And carefully push both sides together.. Might need an attempt or two but after that error gone. If you are sure this connector is perfectly connected then the second cause could be a cable break in the cable running through the neck down.. Considdering 2 out of 3 units i have had cables breaks because prior owners roughly put the handlebars in catching the wire or plug. Can't be 99% sure BUT I'm a 100% sure it is not the battery, break, back light etc.as i tested all those parts seperately between the units. Hope that helps some people Tim
@reviewcity31762 жыл бұрын
Thanks Tim for all the useful tips! I am sure it's going to help someone out reading through the comments. Thanks!
@KronosManuel Жыл бұрын
Hello Tim, could you explain what is this problem ? I have it too (Error 43). it's brake/scree/throttle/battery ... ? thanks
@ErrollJones-s6d10 ай бұрын
KUGOO KIRIN is this the main problem with all the brands 😮
@madalinmilcu14662 жыл бұрын
Hi , not working for me , maybe i connect the wires wrong?
@reviewcity31762 жыл бұрын
Hey, yes, double check - I've had lots of messages saying it's all working fine. Best of luck.
@madalinmilcu14662 жыл бұрын
@@reviewcity3176 i try both ways still not working
@guidoconforti94223 жыл бұрын
Hi. Only the button of the parking sensor will not work or the sensors too ?
@reviewcity31763 жыл бұрын
Just the sensor button. But if you complete my steps I went through in the video everything functions perfectly.
@guidoconforti94223 жыл бұрын
@@reviewcity3176 first of all, your intuition is a very good job for us, so thanks I’m Italian and not all your words in the video are clear for me So if I well understand you put two solutions In the first you keep the ten pins plug in the old board and you duplicate and connect the firsts four wires to the new knob In the second , you don’t use the old board and you connect the ten pins plug directly to the new four pins knob but in this way you lose the function of parking sensor and Auto H Am I right ?
@reviewcity31763 жыл бұрын
@@guidoconforti9422 thanks. But not quite. If you follow the instructions and keep the old board connected you will have full functionality. If you choose not to leave the old board connected and just use the newer 4 pin, you can redirect the wires to the 4 pin but you will lose the parking sensors button (the sensors will work, but you cannot turn them on/off on command)
@guidoconforti94223 жыл бұрын
@@reviewcity3176 hi thanks for you replay. This is very interesting because I was trying the way to have always on the parking sensors. And you know what happens to Auto H ?
@reviewcity31763 жыл бұрын
@@guidoconforti9422 I was mistaken about auto h in the video. I must have pressed it whilst something was disconnected. It is unaffected if you direct the 4 pin. It's just the parking sensors button
@kristianmilano82013 жыл бұрын
C'è un metodo per aumentare la velocità?
@ЖеняДуліба3 жыл бұрын
pls help error 43? what to do
@reviewcity31763 жыл бұрын
Sorry, not sure about error 43
@timharris19352 жыл бұрын
Found error 43, will reply in seperate answer
@barrygreen48183 жыл бұрын
Hi I’m just wondering do you know what error 20 is. And how to fix it plz
@reviewcity31763 жыл бұрын
Hi, sorry I don't.
@chanhtran76683 жыл бұрын
Hi All, I just got this scooter & 've been riding it to work for 3 days ( 6kms each day ) And today on my way back, the scooter suddenly stopped & no way to turn the power back on !!! The battery level was at least 50 to 60% Could anyone tell me what did happen ? Big THX in advance for any help
@ch2o22 жыл бұрын
it sounds like you confused the electronics a bit ...try to push the orange bottom 5 times - you will hear a short beep that indicates that you switched on (or off) the motor ...I found it out by chance (have no instruction guide) and maybe it helps .)
@mindfulmusings1993 жыл бұрын
I've got kugoo s1 error 02.... any help ?
@reviewcity31763 жыл бұрын
Sorry, not sure
@mindfulmusings1993 жыл бұрын
@@reviewcity3176 I have contacted them, the problem was due to the accelerator handle switch. They sent me a handle switch replacement (R) and installing instruction. It is working now! I am good ^^
@MrDudleydawson3 жыл бұрын
Hello is there any speed hacks to get it over 25km?
@hamomelkumyan96873 жыл бұрын
I don't understand if I can watch my recording from my phone instead of my computer?
@SamieMiah3 жыл бұрын
It's not a WiFi camera so need to remove sd card and insert into computer or mobile device.
@hamomelkumyan96873 жыл бұрын
@@SamieMiah got you ! Th u !
@lacku12353 жыл бұрын
My e scooter won't turn on need help asap
@cr7editz6863 жыл бұрын
Please see how to make this scooter faster
@benmurphy45113 жыл бұрын
Hey I've followed your video but it's still not working for me. It's really annoying how your camera dies right on the part that I'm stuck on. Please help cos I feel like I've wasted my money. Only had the scooter for a week before its now not working and flashing 40 at me
@reviewcity31763 жыл бұрын
Hey Ben, so sorry, just came across your comment. Yes, very annoying in regards to the awkward flat battery 🤦your basically replacing the brake throttle for a new one. So, remove the old, install the new and your golden. 👍
@wit01203 жыл бұрын
Hell did you put new brake lever on,or did you just swop wires
@reviewcity31763 жыл бұрын
Remove the rubber handle. Slide the new brake lever on and screw in place.
@lewisl52133 жыл бұрын
just follow ur step by step. Didn't work...
@reviewcity31763 жыл бұрын
I've got it done 3 times now on different cars and it's working perfect. Still have it setup on my own car. Recheck the wires please. Maybe they are on the wrong way round?
@Adrian-yf1zg3 жыл бұрын
Ive got kugoo s1 error 02.... How to clear?
@reviewcity31763 жыл бұрын
Not sure my friend. Sorry.
@Maf10sorio3 жыл бұрын
Fell left to right how do the color go if I wanna connect the pins directly to the 4 pin
@reviewcity31763 жыл бұрын
Try it the opposite way your doing. It 💯 works.
@Maf10sorio3 жыл бұрын
@@reviewcity3176 what do you mean? In what order do the colors go ? Do I have to code my car? Do I have to add my old controller to the wiring too ? Im also the wondering If this works for US cars
@reviewcity31763 жыл бұрын
@@Maf10sorio no coding required. This method you keep the old controller board connected too otherwise the parking sensor button doesn't work. You can just cho pthe wires and connect to the 4 pin but you will lose control over parking sensors.
@Maf10sorio3 жыл бұрын
@@reviewcity3176 why isn’t it working bro 🥺
@reviewcity31763 жыл бұрын
@@Maf10sorio put your email on here bro, I'll message you and you could send me pics of your setup.
@brettsouthers32563 жыл бұрын
just did this.. didnt work
@reviewcity31763 жыл бұрын
Are you sure you followed the steps? I've done a few times now on different cars and it's worked fine. Recheck the wires
@brettsouthers32563 жыл бұрын
@@reviewcity3176 going over it agaim
@mangoguey3 жыл бұрын
Is this for the f10 I’ve been trying to find the part number for my 535i xdrive 2011 so I could at least have a back up plan to buy one just in case I can’t fix the module.
@reviewcity31763 жыл бұрын
@@mangoguey it is for the f10/f11.
@mangoguey3 жыл бұрын
@@reviewcity3176 f10
@ps5stuffguy3 жыл бұрын
They have a new 100 watt usbc
@reviewcity31763 жыл бұрын
They do! Haven't bought one yet though. Let me know how it is if you have! 👍
@gregmcdermott88383 жыл бұрын
Hi i was wondering do you know were I can get the thumb brakes of it my one not working
@reviewcity31763 жыл бұрын
Hello mate, I saw geek buying site had a few spares otherwise I would try emailing kugoo for parts. I sold mine as parts was a nightmare.
@gregmcdermott88383 жыл бұрын
Ok thanks
@dothisexclusives99693 жыл бұрын
Hi there were dd u buy the replacement throttle as I have been searching around the web and have not found nothing. Can anyone help !
@reviewcity31763 жыл бұрын
I got it direct from kugoo. Email their support team. They do take a long time to reply though.