s wilson

Пікірлер

@SuperRobGale 2 күн бұрын

Thanks a bunch! Perfectly explained

@swilson6206 Күн бұрын

Thanks for the comment

@seandever5761 4 күн бұрын

Sometimes you can also pull up on the nut and Johnny bolt with a pair of channel locks and while applying force in an upwards pulling motion start spinning the nut off with the pliers. I’ll also sometimes just stick a knife or flathead under the washer and do it like you did in this video. Never tried this specific trick though maybe next time!

@swilson6206 4 күн бұрын

Thanks for the comment!

@seandever5761 4 күн бұрын

@@swilson6206 of course man. Fellow plumber here

@lizglow 5 күн бұрын

It does such a great job cleaning, were getting along without the hot just fine! Good to know my SpeedQueen is indeed PERFECT after all! thanks for the video.

@thetrickster4526 8 күн бұрын

Thank you so much! Since the bulb base in my chandelier was broken, techniques like using pliers or the potato trick were impossible. However, your technique was extremely useful-the base came out easy-peasy!

@swilson6206 8 күн бұрын

Glad it worked, thanks for the comment!

@jonathanw8461 8 күн бұрын

Cost to replace?

@swilson6206 8 күн бұрын

I can't remember exact cost, I think it took about 4 hours to dig the hole, 4 foot deep, 3 feet wide. Then there was the cost of water valve, the long tube, and gravel.

@jonathanw8461 8 күн бұрын

@@swilson6206 thank you!

@barbaracompton4822 9 күн бұрын

Awesome !!! Just what I needed to see from begining to end ! I was told I could never do it this way and needed to rent an auger and buy the parts that go with the auger. I knew this way was possible. Thanks a bunch !!!

@swilson6206 9 күн бұрын

Yes, it is possible, and it is also a good workout that can save you money on gym fees. Make sure to use a wrench with a long handle. You can slide a pipe over the wrench to make it longer. Thanks for your comment.

@WaldekSzewczuk 10 күн бұрын

what is the part number for impeller and where did you bay

@juliacastro8505 11 күн бұрын

mine asks the same no matter what name i put

@swilson6206 11 күн бұрын

Are you renaming the project in the upper left corner?, way up to the upper left. Thanks for the comment.

@BradWojcikPharmD 16 күн бұрын

Thank you! Worked great!

@swilson6206 15 күн бұрын

Thanks for the comment!

@powerbongo922 18 күн бұрын

You solved my problem. thank you sooooo much

@richardefriend 20 күн бұрын

BTW-a socket from a ratchet set, which can be selected for the perfect fit, with double stick tape on the end works even better. But thanks for the tape suggestion (since the old plyers trick failed miserably).

@swilson6206 19 күн бұрын

Thanks for the comment!

@Deedraa 22 күн бұрын

Thanks

@swilson6206 21 күн бұрын

Thanks for the comment!

@davidarwood6264 Ай бұрын

Nobody....Nobody is even going to to tighten down lugs for me ever , ever again. I will do it myself by hand . If they do not like it , I can go somewhere else. PERIOD

@swilson6206 27 күн бұрын

Thanks for the comment! They are probably afraid your tire might fall off and they may get in trouble!

@medicalmiraclenatural6454 Ай бұрын

Simple trick... Back side ..there is censor cable.. during spin its getting shaking and loose connection.. you just refix with tape ..

@swilson6206 Ай бұрын

Thanks for the suggestion. Hope it works!

@bobby6631 Ай бұрын

some good tips! I knew about the breaker bar, but didn’t have one or I mean the extended one helps a lot. But the jack stand tip is the best. I can’t tell you how many times the lug wrench wants to bend down the jack. Stan prevents it and gives you that extra help.! Tnks!

@swilson6206 Ай бұрын

Thanks for the comment.