have you cleaned the strainer on hose going to compressor

I got a plug and the parts dealer put it in my old starter, the parts dealer couldn't get the new cable out and told me to put the starter in with it. I told him that was the old one. Lol, he had to get it out and struggled, promising a replacement if it broke. I need to modify this stuff, but on the other hand, it's a great anti theft device, nobody can start the vehicle if the cable keeps coming lose!

This video was the most helpfull one I could find on servicing the water pumps. Thanks

11:29 - That shift slider is prone to cracking .

Thank you sir. Saved me $1000. Your advice is impeccable…💯👌🏽

Yep I did this after I broke my connector. Fuck those plastic ends. Now I have piece of mind

Yep I did this after I broke my connector. Fuck those plastic ends. Now I have piece of mind

This was definitely helpful. Appreciate the video

Can you plz give me an update have you had any problems since you did this? I’m thinking of doing it today

How or what was you using to get that great overhead view?

Love it. Might just fix my problem

Best and most informative video I’ve watched all year.

You don't need to splice in a new connector if you break the red clip. The plastic parts of the connector easily disassemble. Buy a new connector pigtail and pry out the gray core with a small screw driver or steak knife from the side. Next push two small paper clip pins into the two small holes on each side of the metal connector until they bottom out. Now slide the plastic connector off the metal crimped wire connector. Repete with the broken one then simply slide the new connector then the gray core onto the existing metal crimped connector.

I got the leak to stop, but I have vibration and noise coming from helm. It is just air bubbles possibly?

Subscribed

Bags of water softener salt works great and real cheap in 50 lb bags

I was extra cautious when dealing with my red tab and it still shattered from being so brittle. My starter should arrive today and I will install it tomorrow morning. I have everything broken down already and I’m definitely going to use the ring terminal method.

Very well done video

Glad I found this video. I'm on my 2nd Uflex helm in less than 6 months- both leaked. Haven't even had the chance to take it out on the water yet. Uflex helms are overpriced junk.

Hello. How many day do I havle to keep the bait in salt.? Manythanks

What rod is that with you and the bull red? I don't see many long baitcaster rods without way too much spine. I want a long one 10'+ of medium capacity (1-5oz rated) and I've had no luck finding such. It seems they have plenty down under and also across the pond. USA? not so much unless you go custom and I checked on blanks--higher than I expected! Is that a Penn?

Great video!! My 2007 mercury optimax 115hp 2 stroke is hard to start when warm up. It cranks but doesn’t starts. When you let it cool down for about 10 minutes it starts up without any problems, I have water flow. Any idea what it could be? Thanks 🙏🏽

I love that you showed that hack , I’m subscribing to your channel, I do things the same way ….GO BILLS !!! JA 17 !!!

They salt the prawns with salt and sugar in Greece that works really well. Just put some in salt for my holiday next week. Thanks for the advice.

I had to replace my starter . Good video explaining everything. Saved me lots of time.

Thank God for this video

Dude - I don't care what Anybody Says or Thinks ... What you did to that wire is an UPGRADE in my opinion! That ridiculous plug with that stupid clip thing on it is a BAD DESIGN - Nuthin' Wrong with using a Simple Ring Terminal to connect... In Fact, it's probably BETTER!

I hate that the heat source is dead in the middle

un grand merci depuis la France 😊

Im over here workin on a sump pump. Brilliant! Thanks a bunch bud!

What salt to be used? After adding salt it should be kept outside for how many hours

Just to end my own question, I got the answer from a dealer in Norway. On smaller engines, the switch is located under the separate oil tank. :)

I See You already answer'd related to carlking''s 115 hp.. anyway mine is an old machine from 2006, runs great, but will not pass 2500,-

Hi, I have a 75 hp with the same problem .won't run above 2500 rpm,, I cant find the swith you show in this great video.. Do you know if it could be placed in the handle-bar assembly at the controll-panel ? Regards Paal

Will thawed frozen shrimp work?

You can't get the water pump bolts out because of electrolysis I would've checked all the zincs in there powerhead because with the aluminum hull it's just going to eat that engine like it was a vat of acid

Takes about 30 min to get out and 30 min to put back in. 10 minutes cussing 10 min resting your neck And 10 min of actual work

Thanks

i using pure white coarse salt i don't know it will work or not

Great vid, thanks. The tips and commentary are super helpful, and critical - a mic would minimize background noise and completely transform watchers' ability to hear you!

Great video. I've done two of those. Broke red clip both times. Whats the trick on the red clip 😅

thanks, good one. Another bitch diagnosed

Should be put in the freezer or bottom part of the refrigerator I mean just cool it

where is the shift switch on a 2008 mercury optimax 115

Best salty shrimp video I've seen in years.

Add a pinch of garlic powder... For bass use a little anise..try to use pool salt or sea salt. For catfish do the same with chicken pieces welcome to nevwr being skunked again Works great with squid

I'm going to try this with creekchubs, common carp fillets, bluegill fillets, and shad to fish for channel catfish. If this works, I will be vacuum sealing the baits and storing them in my garage in a 5-gallon bucket with a screw-on lid. I hope this goes well. It so, it will free up space in my freezer for more catfish nuggets instead of storing frozen bait. 😉

Thank you

How long can you keep the bait in refrigerated

Checked this one I unplugged it and it work so I said it’s the switch but I replaced it and it was still doing it won’t rev up then I took it back off kept the wires plugged but not installed and it’s working again. Need help seems to be working without it installed with the wires connected. What else could it be?