The EZ start can light the glow plug up just as hot as an igniter. The problem is, there is a few places where it can get corrosion, or old fuel around the contact point can be problematic for the connection. Btw we both live in Idaho
@joshmatthiesen45526 күн бұрын
Good video. But I disagree on ditching the EZ Start glow plug wire. I have a Revo 3.3 and don’t have any problems with it. Other than my starter motor burning out. I even upgraded my starter wand to use a 2S lipo battery
@Bullwinkle3915 күн бұрын
I've been telling people this for years, I can't believe it's not common knowledge yet
@Flipside690029 күн бұрын
Probably shouldn't be adjusting the idle that much if this is an issue. Set your idle gap to mfg recommendation and tune from there.
@arturos.l.224829 күн бұрын
Hey the reason youre blowing so many Glow plugs is because you ran VP fuel without richening the fuel mixture. The traxxas top fuel has much more oil than the VP. In the long run, youll foul out way more traxxas glowplugs with that type of fuel, and the OS ones will foul too, but they'll last longer. Your engine appears to be running a little lean btw. Avoid tuning the carburetor a lot. Try not to make large adjustments where you have to unscrew and rescrew the needles, the carb is very fragile and gets damaged easily by this. Its better to leave these traxxas carburetors Alone for the most part and use traxxas fuel, and leave the idle reasonably high to compensate for the rich fuel mixture going in. Since youve already run it this way for a while i recommend just seeing how long it lasts, then buying a New, non traxxas engine with a base tune carb
@Duckhunter_GokillembirdsАй бұрын
I’m up in north Idaho and I have a tmaxx so same truck, same state, and same area of the same state, we should hang out where you at couer de lane, Kellogg, pinehurst, post falls? Where you at cuz we now friends
@TheHobbyistRcАй бұрын
near cda
@design2survive5 күн бұрын
Near sandpoint..just picked up an old revo 2.5..need to do a N Idaho rip! I normally fly planes..but this nitro car is pretty fun.
@Joey.BoogieАй бұрын
Thank you for getting directly to the point, great video to help me decide!
@mr.fridge6710Ай бұрын
👍
@joncatojohannessen2560Ай бұрын
Hey I know im late but wil this work on a castle x8s hydra?
@TheHobbyistRcАй бұрын
Yes it will.
@joncatojohannessen2560Ай бұрын
@@TheHobbyistRc okay thank you!
@luiscotto6659Ай бұрын
I just installed mine yesterday and was freaking out cuz that loud buzz that comes from it but I see youres also makes same noise
@B-Eazy89Ай бұрын
Looks good, im getting ready to detail my engine cover up. What did you use to paint it? I'm new to the painting part...
@TheHobbyistRcАй бұрын
I used TESTORS model paint.
@B-Eazy89Ай бұрын
Awesome thanks a lot! I appreciate the help! -Brad -B-Eazy
@TheKerstingm2 ай бұрын
What tires are you running on your Revo?
@michaelgraham29432 ай бұрын
👍
@silentwonder-chilled3 ай бұрын
i got a mamba XLX and the calibration is rubbish i will never consider electric ever again, Nitro & gas only from now on.
@25781363 ай бұрын
Why isn't it shifting to 2nd
@Carguy-fn5nf2 ай бұрын
Its the 2.5 it doesn’t have 2 speed
@PriusTurboАй бұрын
mine does
@revoe43 ай бұрын
Can’t wait to see it
@revoe43 ай бұрын
Can’t wait to see it
@mexicanbeetle22934 ай бұрын
This came in clutch I was about to start tuning my rc car
@ONFLOOD-RC4 ай бұрын
Awesome truck and tips mate!!! 🥇👍👍👍🤜🤛😎
@fredbradick84045 ай бұрын
the interior what website can that be found on please also does it come with the head and streaming wheel
@TheHobbyistRc5 ай бұрын
The interior comes with the kit, but I believe you can buy it separately on Horizon Hobby's website.
@nickstone19055 ай бұрын
How many turns out was the idel screw 🤔
@MannyGunzz5 ай бұрын
I fixed mine with a thin strip of Teflon tape on threads then used this info works great
@andyfrancis52776 ай бұрын
Modify your ez start to accept a lipo, no need for a seperate ignitor. Traxxas fuel is garbage and you replaced the cooling tower, not the head. Idle is too high and I never heard it hit 2nd gear, that is adjustable too.
@motorbreathjz6 ай бұрын
he replaced the cooling head. theres no such thing as a cooling tower.. there isnt any modification needed to use a lipo battery in the wand.. you just plug the dam battery in the wand..
@motorbreathjz6 ай бұрын
he replaced the cooling head. theres no such thing as a cooling tower.. there isnt any modification needed to use a lipo battery in the wand.. you just plug the dam battery in the wand..
@StevePappas-f2m6 ай бұрын
Stop
@MannyGunzz6 ай бұрын
I actually stripped out mine last week..i wish i seen you video thank you
@thecarter70257 ай бұрын
Are you sure that’s not 500k lol
@favulus17 ай бұрын
did you mean lc3 glow plug? there is no ic3
@andrempmorais7 ай бұрын
Thanks for the tips great video very informative keep it up! ❤
@erazco65688 ай бұрын
Ok I’m cutting my center plate out thanks I got a axle mounted servo but the type of truck I got my plate gets in the way
@weewick77798 ай бұрын
So to summarize. Use good fuel, get a good cooling head and get a glow plug and igniter
@RogerJohnson-j9v8 ай бұрын
i switched to the VP fuel as well and the truck seems to be running better
@ManuelOrtizification8 ай бұрын
OS plugs, yes. Different glow igniter, not needed with the OS plug. Less oil, no. The traxxas motors love extra oil. Also your idle is super high
@gavinpope26028 ай бұрын
What happens if your steering wheel is your throttle. How do I fix that
@danielsantos86258 ай бұрын
Flip your wires around on your receiver
@dereklewis83668 ай бұрын
Weak video bro
@williambreeze26599 ай бұрын
Thanks sir!
@packmanbrosefreind87439 ай бұрын
So I have a problem that. It will start it won't go
@nephtalirodriguez481910 ай бұрын
Lo voy abrobar y te aviso si funsiona ❤
@zachattack201610 ай бұрын
Os11k carb and aftermarket rod
@josephfast58878 ай бұрын
And ditch the electric start and ez wand system
@glastornjet7310 ай бұрын
Or you could just bring the idle up slightly with the radio turn the screw and let the motor come back down to an idle... 🙄
@zowiewowie445810 ай бұрын
never have I had this problem
@dancearoundtheworld536010 ай бұрын
i got the same issue making a 8x4 scx24 and somehow on reassembly it doesnt reach but i got a fix in mind
@paololonzi11 ай бұрын
The precision of the back to the center is good?
@TheHobbyistRc10 ай бұрын
Very much so.
@hilham8911 ай бұрын
I think that you ment the head would fit the 2.5 and 2.5r. If its for a 2.5 it wouldn't fit the 3.3
@TrokaRC11 ай бұрын
Good info.
@MatthewMcKenzie-qk8vz11 ай бұрын
What motor do you run
@TheHobbyistRc11 ай бұрын
Holmes Hobby Crawlmaster Expert 13t 540.
@bazzani2111 ай бұрын
Those highly angled shocks have far far more negatives than positives. Do a proper suspension, and don't worry about flex friday
@OU812NVME11 ай бұрын
Wow I've been using 10 percent fuel for over 30 years and not had a problem maybe that's the issue...... but I know you guys want to go as fast as you can
@DerekRC11 ай бұрын
Helpful tip your idle is way to high.
@Otiesh Жыл бұрын
Thanks brother your instruction was just straight forward, imagine I had the manual but your explanation is self explanatory. You saved my day.
@benle4 Жыл бұрын
Hey man, running this gearbox in a road car build and cannot find any gear up gears. Do you have any idea where I could get some? I am based in UK.
@TheHobbyistRc Жыл бұрын
There are several companies that sell 48 pitch gears including Amain Hobbies, Tower Hobbies, and Amazon, you probably going to want to look for a large pinion gear and a small spur gear to get less gear reduction.
@benle4 Жыл бұрын
@@TheHobbyistRc yeah, I can find different 48 pitch gears but it’s finding one that fits on this spindle. Do you have any links to items for it? I can’t find anything that would just swap over. The only line for like is the metal replacement 87T gear! I was hoping for something more like a 50T. Any help would be appreciated Thanks
@TheHobbyistRc Жыл бұрын
@@benle4 www.amainhobbies.com/48-pitch-spur-gears-option-parts-cars-trucks/c1874?fa=15_923|15_928|15_2657|15_2656&lg=fa15 here are some spur gears off Amain. they won't be a direct bolt on fit, but it would be pretty easy to adapt them to your gearbox. looks like the direct bolt on gears only go as low as 69 tooth.