Bicycle Motorsports

Пікірлер

@mantishalen5303 28 күн бұрын

Couldn't help but notice this guy has no inline filter

@kenwileman6373 Ай бұрын

I have missing teeth on the smallest tooth wheel of the two on the right side of the engine, how do you get those peices out?

@adamsmy8121 4 ай бұрын

What kind of carburetor is that? Whats your top speed? I cant get mine over 26mph

@stephenmichaelolney5880 7 ай бұрын

This was so much help as I am knew to the game piecing together engines, thank you

@RightLane393 9 ай бұрын

that what i did, but it still a little slip and it doesnt work for me.

@leemilica 9 ай бұрын

How the fuck do you remove the clutch nut? I HAVE BEEN GOING AT IT FOR THE PAST 2 FUCKING DAYS USING THE BIGGEST WRENCH AND PLIERS I COULD FIND AND I BENT THE 3 PINS LIKE 15 TIMES ALREADY AND THE FUCKING NUT WONT LOOSEN

@trevorread8668 10 ай бұрын

Where can I find a replacement shaft the gear goes onto I picked a bike up that the nut and bolt on the chain side are stripped to hell😅

@MrMohamed323 10 ай бұрын

Is the flywheel in the engine sufficient for the piston to rise up to compress the mixture and complete the cycle?

@PaulyFSF 11 ай бұрын

slow no torque i have a shittier setup with a larger sprocket and i hit 40mph np

@wojtech270 Жыл бұрын

Thank you!!!

@CUBANIDAD Жыл бұрын

Your video skipped the hardest part!!! "I already have it loosened, so I'm just going to remove it by hand." HOW DO YOU LOOSEN THAT SHIT?

@MikeNBikes Жыл бұрын

I needed a straight to the point video like this, thank you.

@michaelbrinks8089 11 ай бұрын

My teeth wore out quick. I'm gonna order one but this time heat treat & temper it. Like I did my rear sprocket which has same mileage as front sprocket but has no major wear yet. All you need is propane torch or Mapp gas & simple heat treat/temper instructions. They bother to heat treat them in China in order to keep manufacturing down + u end up buying another one sooner. Just thought 💭 It'd be a good idea to heat treat the puller tool also.

@stanislavbryndza Жыл бұрын

Takto môže meniť ložiská len amatér!!!

@irondan007 Жыл бұрын

my suzuki zeus 125 cc bike has vm 18 mikuni carb. On the left side of the carb just below the choke lever there is one rubber diaphragm(engine side) fixed diagonally with two star screws and also some sort of an electric switch top side which goes to the cdi unit ,(two wires) .Please explain the exact function of these parts ?

@tallishadley624 Жыл бұрын

Mine doesn't have a thread for the tool how do I remove it without the tool???

@blackout260112 Жыл бұрын

Nice wheels!!!!

@korymay3126 Жыл бұрын

thanks for the info and link,

@sebastianlorant6502 Жыл бұрын

"standard master link and use the 415 half link" what is the difference?

@tinypurplefishesrunlaughin8052 Жыл бұрын

Performs like sh!t looks like sh!t. I’ll never install that fixed tensioner. And as far as we are talking shitty looks and performance get a load of that RAG joint sprocket crap. jeez Whatta piece.

@Op1zilla Жыл бұрын

Short an easy, 😁👍

@lifesadventureskeepingitre1180 Жыл бұрын

I'm new to the motorized bicycle and I'm finding it very interesting especially working on these small engines you were very informative good job.

@MeiGunner Жыл бұрын

i cant Get the Bolt off ,, lol

@BicycleMotorsports Жыл бұрын

Just use a socket wrench and turn it counterclockwise it should come right off.

@MeiGunner Жыл бұрын

@@BicycleMotorsports yeah ,, it Was a motor from when i was A kid in the 1990's .. and when i open it , it was All rusted on the Magent and The Coil ... SO after some Pb blaster , and a new Coil , its running good! ( no New Magnet , just CLeaned it with Sandpapper ) God Bless stay Safe out on the Road

@leahresnik9208 Жыл бұрын

Also, what engine did you purchase for your motor bike? In your video you were talking about how you upgraded the carburator? Can you please provide more information on that? TIA!

@BicycleMotorsports Жыл бұрын

I have a CNC Billet aluminum motor on there now that I assembled myself with balanced cranks and upgraded clutch. However the carburetor I upgraded to was a Mikuni vm18 clamp on carburetor. Just below is a link. I purchased it from treats. If you check out some of my other videos You'll see the carburetor www.treatland.tv/mikuni-vm-18mm-p/mikuni-18mm-vm-round-slide.htm?gclid=Cj0KCQjw_viWBhD8ARIsAH1mCd6SBWvJkXb7ErgKipjgGpxD4ccCKSHxfSAVh_uyXRm5WiMerx2Np8IaApHdEALw_wcB

@BicycleMotorsports Жыл бұрын

What kind of setup do you have?

@BicycleMotorsports Жыл бұрын

When upgrading to this type of carburetor just know it's a little more complex than the stock carburetors that come with these motors. You might have to tweak it with the jetting and fuel intake and in some cases the fuel float. I've made a few videos addressing the aforementioned.

@BicycleMotorsports Жыл бұрын

You're also going to need an 18 mm intake manifold for the motor to match up with the upgraded carburetor

@BicycleMotorsports Жыл бұрын

Here's a link to another video I did on a sprocket removal and you can see in the video the reed valve setup that I have that the Mikuni carburetor would connect to. The Reed valve will help immensely with fuel blowback into the carburetor which can mess up the fuel to air mixture ratios and cause fuel leaking out of the carburetor onto the bike frame. I recommend a reed valve. you might have to change the carburetor jetting. kzbin.info/www/bejne/gofKn4iciNSEgdk

@peepeecaca6926 Жыл бұрын

I snapped i peice of my engine block doing this

@BicycleMotorsports Жыл бұрын

What piece?

@peepeecaca6926 Жыл бұрын

@@BicycleMotorsports the top right screw hole the whole thing snapped of I just have 2 bolts holding the clutch arm cover on it works

@Billy-ky8qc Жыл бұрын

How can you tell if your engine is 8o.cc. Or 50.cc

@BicycleMotorsports Жыл бұрын

For whatever reason these China girl engines are 66 and 80cc used interchangeably. Most people just refer to it as a 66cc

@eddiemarines5861 Жыл бұрын

We're can I get the woodruff key and is it m.m.or in.s or what size?

@BicycleMotorsports Жыл бұрын

You can get Woodruff keys from bikeberry.com or on Google search bar just type in 66cc engine Woodruff key. They are standard size for those engines.

@ryanmckenziegilbert4950 Жыл бұрын

Do I have to pull it off to put the chain on

@MrMohamed323 2 жыл бұрын

How can the bassum go up in the compression stroke, given that it is only one?

@linkgroundwalker 2 жыл бұрын

In your case I don’t think replacing it was worth it, in about 3 months or less you’ll have the same play in it. Ride it until it tells you something is wrong by puking it’s guts out or screaming.

@joneserupinsmoke9161 2 жыл бұрын

Bro heat the end of expansion chamber up with a hand torch and then bend it in towards the bike or you can just put a 20 degree angle elbow on it or something

@joneserupinsmoke9161 2 жыл бұрын

Is the seat spring loaded?

@joneserupinsmoke9161 2 жыл бұрын

Bro when you use the high performance exhaust the expansion chamber or whatever you were using with no baffle you cut the muffler off of the old stock ones and use that baffler

@joneserupinsmoke9161 2 жыл бұрын

Bro I had the same issues on one of my builds bit yeah best bet jist replace it it's just gna keep happening 👍😃 thanks for information though bro

@Nostalgik64 2 жыл бұрын

Your also supposed to add a lubricant preferably grease to lubricate the threads on the Clutch Gear Puller to prevent any cross threading and to make smooth contact with threads.

@garygushue4273 2 жыл бұрын

Thank you so much I was trying to figure out how to get the chain off without depressing the clutch as I found this motorized cruiser in the trash & fixing has been fun

@OddBallPerformance 2 жыл бұрын

For anybody that watched him install that bearing. Please, never ever ever ever ever install a bearing into a case by pushing or pulling on the inner race. Use the old bearing, or better yet a bearing installer tool, and apply only pressure to the outer race. Pushing/pulling on the inner race will distort the cage and potentially shorten bearing life.