It’s wild how many more views you get on a video like that. But like you I want to document the real side of this!

@@BayouBrit Exactly. I shot some footage of money collection and I'm going to post one just to see how much more it gets than actual content... I'm sure it will be 200% more at least.

Presoak leak- check the foam generator on top of the drivers side of the gantry. First gen wizards used brass fittings and they could go bad with caustic chemical. You should also have two solenoids in the low pressure box on the driver's side. Make sure the solenoid for the top boom is closing. You can pull one of the wires off and turn on the presoak pump to check it. Rocker panel blaster can be fixed by a welder pretty easily. I use 0503 IMEGs on the side nozzles and 1506 IMEGS on the top boom if it only has two Check you alarm history to see why the machine reset. These machine are not complicated but the 2.0 has better diagnostic features. Before you put in a brand new auto in consider a used water wizard 2.0. You can get them for less than 10k and they will mount on the same rails. They are very capable machines

Re bay height I was thinking the same during the edit. My iba takes up to 7ft 6 and these bays really are short. It’s a very odd site in a small town

Hey. It’s one of the Warsaw products, I’m just not sure which one warsawchemical.com/product/category/car-wash/self-serve/foam-brush-self-serve/

@@BayouBrit thanks. The purple is really neat. It makes your foam brush different than everyone else.

Yeah we use a little bit more than othered but we get lots of good feedback. Except when I didn’t turn the air down as the heat started to ramp…small adjustment and it’s slowly running off cars again even if people put the foam brush on a dry >100 degree 🛻 🤦‍♂️

Oh yeah I’m not envious of that at all. It’s like this stuff we inherit, gotta make the most of what’s there!

Not quite. The presoak is driven by a boost pump. The cat pump doesn’t run at all for pre-soak. It was a wild problem to troubleshoot

Interesting all 4 of my JC stands run through my Hp pump

I second this assessment. It seems like there's not enough OOMPH to push that presoak into the line with the HP water on. If it's not that, I'm as stumped as you!

Yep! If there’s a way to do it wrong, that’s the way I’ll try first!

Thanks for the insight!

My goal is to get our pump rooms working as efficiently as possible then de clutter the heck out of them! From my experience most operators will show you how stuff works if you ask.

No I used the wrong export settings from Final Cut Pro. Bit of a learning curve using HDR

I can't speak for tunnels as I don't think i've ever used one. So i'll take your word for it!

I wish I could claim credit for it. But it’s a “polar freeze guard” system.

That’s a keen eye! It does not. It’s on my list of things to fix…one day that list will get smaller!

Absolutely…I just have to fix the 3ft crack on my windshield first 😬

@@BayouBrit when and then you going to film it the automatic

It’s a privilege to know I get to replace all this stuff 😂

I think old rotary switch boxes can last a lifetime. But the push buttons we had were a single unit for all 12 switches which was causing us issues. Where are you located?

@@BayouBrit Dallas, Tx

I sure hope it will! Sadly the flags are still missing. We may end up removing the canopy and adding some floodlights instead.

💯 a lot of these “bad” sites could be improved with a few adjustments and some check valves

Yeah I would have love to have seen that.

If like to get a new in bay automatic, some colourful lights for the bays, an outdoor vending machine, a whole tommys tunnel… Realistically I can only afford air fresheners right now…