Haider

Пікірлер

@s4ms0n1t3 Жыл бұрын

The milltek centre section has a resonater in, I take it the cobra one was straight through?

@fearthereaper5663 2 жыл бұрын

Hello this can cause burning oil smell ? Thanks a lot

@Haider_Malik 2 жыл бұрын

Yes in some cases if the leak is really bad it can drip onto the hot exhaust manifold and burn off

@fearthereaper5663 2 жыл бұрын

@@Haider_Malik thanks a lot

@fearthereaper5663 2 жыл бұрын

@@Haider_Malik but it seems that the nut is below the exaust manifold . Is correct?

@Haider_Malik 2 жыл бұрын

@@fearthereaper5663 It could also be a leaking rocker cover gasket at the back or side of the block. This oil could definitely make contact with the exhaust manifold. Do you have oil marks on the floor where the car has been parked?

@fearthereaper5663 2 жыл бұрын

@@Haider_Malik yes a lot

@PaulDo22 3 жыл бұрын

What are the symptoms that would indicate it needs replacement?

@robertabalos3353 3 жыл бұрын

Do you know if 2005 X5 3.0 M54 engine is also equipped with this CPV? My X5 also has leak symptoms in the same area.

@Haider_Malik 3 жыл бұрын

Robert Abalos Hi, unfortunately I’m not familiar with the M54. Find the parts diagram on realoem and check if it does have a cpv. I hope you find the cause of your leak 👍🏽

@Jdmbuilds 4 жыл бұрын

Are these only for m3 or are they Also on m54 motors

@Haider_Malik 4 жыл бұрын

I believe its only applicable to the S50/ S54

@LateNightRituals 4 жыл бұрын

Nice

@MyRcGoSlow 4 жыл бұрын

Would this fix a p0011 ?

@Savorychicken41 4 жыл бұрын

That flat head took is from Harbor freight. Super cheap for a whole set.

@Haider_Malik 4 жыл бұрын

Great to know, I wish we had Harbor Freight in the UK.

@isrealperez9069 5 жыл бұрын

Is this only for m3 only I have 2004 bmw325xi

@TheMaldenc 5 жыл бұрын

Perfect, detailed, straight to the point! Thank you!

@Haider_Malik 5 жыл бұрын

My pleasure Sir :-)

@jamesmcilroy9273 6 жыл бұрын

Awesome video, just been fixing mine using this! It's a tight fit, and crap if you haven't got slender hands. Getting it out was ok, but the amount of swearing trying to get the new one in, now that was spectalular... I'd advise anyone to hold it with pliers in position, then screw in with your other hand, then quickly use the tool by hand to screw it in enough to have to start using the ratchet. Glad I've done it though, and this video gave me the confidence to, so cheers! Awesome work!

@juice0wnzzz 6 жыл бұрын

Did the oil need to be drained in order to do this?

@Haider_Malik 6 жыл бұрын

Johnny No need to drain the oil. As long as the engine is cold very little oil, if any, will come out.

@juice0wnzzz 6 жыл бұрын

Haider A thank you, I great appreciate it!

@CiscoKidd055 6 жыл бұрын

Mpower22 lol i got the tool and O rings from the same guy to fix my leak here in the US..CHEERS!! good Vid.

@aksman1964 6 жыл бұрын

Thanks for the video, really helps me out 👍🏼

@emilepapillon2275 6 жыл бұрын

How much did you tighten ? Approximately ... qualitatively ...

@Haider_Malik 6 жыл бұрын

Emile Papillon Torque to 58Nm or 43ft-lb then turn a further 90 degrees. It’s difficult getting a torque wrench up there so I just did it free hand based on feel. Still holding up fine over a year later.

@blaizefed 6 жыл бұрын

Great video man. Very straight to the point. well worth the 5 min.

@y2ksierra 6 жыл бұрын

Great video and very helpful. Thank you for uploading it!

@kuruption1983 7 жыл бұрын

It definitely helped me despite your belief :D

@l0lwut123 7 жыл бұрын

thanks for making a video of this. i read the writeup by heckafunctional on m3forum and wasnt sure how to get access tot he bolt even though i bout the socket and the viton o rings

@Haider_Malik 7 жыл бұрын

No problem at all. Glad you found it useful! Good luck :-)

@GRM42192 7 жыл бұрын

Really nice. You have the Cobra exhaust and which 2nd mid pipes or are those factory?

@Haider_Malik 7 жыл бұрын

Hi, its running factory downpipes/headers, ebay decats, cobra middle section (straight pipe) and then finally the cobra back box/muffler. I wouldn't recommend this setup, way too much drone!!

@GRM42192 7 жыл бұрын

Thanks man. I own a '06 E46 M3zcp just it factory gives a bold tone no tin can sound if you know what I mean. But although I just want it more louder and bolder. By any means did you experience that sound heard the exhaust has to be full titanium and wasn't sure if the cobra is?

@eduki 7 жыл бұрын

Heheh, It was my first fix to do on my M3 :) i did it the same way like you did, but later i helped to other friends with this and it´s much more easy to access with these short kind screwdrivers with the same kind of tip at the end (i´m sure you know what i´m talking about) This way you can access on the same spot with your hand, don´t have to have a hard time trying to place the ratchet ;) NIce DIY ;)

@Haider_Malik 7 жыл бұрын

Hi, Yes seems to be quite a common issue - damn O rings! Great tip, would have made my life easier lol Thanks for sharing :)

@Arsenalusa 8 жыл бұрын

Thanks for posting mate. The BMW dealer here in san diego also referred to this as the "engine euro valve".

@Haider_Malik 8 жыл бұрын

Your welcome :-) Great to know, I'll add it in the description.

@yruhatin100 6 жыл бұрын

Same here in Phoenix

@SteveMillerhuntingforfood 5 жыл бұрын

@@Haider_Malik Thanks for that, now I know what the BMW dealer is calling a "Euro-Valve". Sterling BMW in Newport Beach, CA wants $1000 to replace that valve. I'm truly offended.