Hello, very good design, but I have a question because I didn't understand anything. After you put the last paint (black), how does the laser remove it and leave the colored paint on the picture underneath? Something is missing from the clip, I don't understand...
@tbncbn714310 ай бұрын
hi ..can do this on faux leather?
@NancyJones-k4y11 ай бұрын
Why does it say wood? Did I miss something? I watched the entire video and only seen you do tile.
@thekittyrescuingcouplemega463311 ай бұрын
There were zero tiles in the video. If you watch the entire video it shows them spray painting wood squares with various colors (starting with white).
@bobbiejordan204011 ай бұрын
Looks great Wade.
@paulwelchjr6769 Жыл бұрын
I have a few questions if we can talk about the settings and how many layers of paint do you do
@paulwelchjr6769 Жыл бұрын
How many coats of black did you use
@Thecraftyblacksheep Жыл бұрын
I have a question. Is that epoxy or just clear coat spray painted on?
@IronCladLaserCo Жыл бұрын
2 part crystal clear extra hard bar top epoxy
@Thecraftyblacksheep11 ай бұрын
Thanks man. Your works amazing
@cheatyx1995 Жыл бұрын
Great Work what seetings do you use for this in Xtool?
@jadjr74 Жыл бұрын
where did you get the designs?
@MarilyneCortiana-yp5sm Жыл бұрын
Super idee j'adore
@Lord_of_ChaoSan Жыл бұрын
On the epoxy, did you just dip the coasters into a bowl of epoxy then set them out to dry? Or did you wipe/paint it on in some way? I'm curious as to how you applied the epoxy- that's the real question. Great vid!
@Lord_of_ChaoSan Жыл бұрын
Quick bump- I'm very curious about my question if you're not to busy. Take care!
@pdeandajr4 ай бұрын
@@Lord_of_ChaoSan I would say he probably makes a border around it, pours the epoxy and then rounds out the edges by sanding and buffing it out.
@TubeScavenger Жыл бұрын
You engraving elephant ying-yangs? Who wants an engraving of an elephant's butthole?
@worldwidewinners8138 Жыл бұрын
Subscriber #500 here, where's my prize? 😄
@warrenjameson5465 Жыл бұрын
Your FIRST coat should have been a PRIMER, so the other layers don't get absorbed into the wood. You may also want to mention to wear either a mask, OR Respirator when working with spray paint. Covering work that you don't want overspray to ruin, etc...
@theodoreburns1330 Жыл бұрын
It isn't a spray paint tutorial lol, it is how to get cool laser results- and the results speak for themselves.
@IronCladLaserCo Жыл бұрын
Uhm, that’s why I used the white. I explained that in the video. You don’t want to use a primer, you want the lightest color you can use as the base, thus the white as I explained in the video, the purpose of the white is to absorb into the wood and lay down a base so the other colors won’t get absorbed, which is exactly how it works out.
@chrisk926 Жыл бұрын
In the video, he shows the white being used for the FIRST coat(s) is an indoor/outdoor PAINT + PRIMER. Paint comes with instructions on how to properly use the product, what precautions to take using the product, and other information the end user can read themself as directions can change from one spray can to the next even if made by the same brand.
@sumtingwong4693 Жыл бұрын
@warrenjameson5465 ... Alrighty Karen. I DON'T think he NEEDS any help from you, the outcome speaks for ITSELF. 😇
@HeavenLeeMadeOnEtsy Жыл бұрын
Amazing designs, thank you for sharing the technique. They ended up looking amazing.
@coreyhelton1995 Жыл бұрын
I still need help with the settings I have a 10w lazer
@IronCladLaserCo Жыл бұрын
@@coreyhelton1995 sacrifice a canvas painted with same layers and colors you’re gonna do and then use the array test grid function.
@mackieb6989 Жыл бұрын
That’s beautiful my friend. Too bad you didn’t show how you put your topcoat on. Maybe you can make a second video for that part. Thanks for sharing.👍
@IronCladLaserCo Жыл бұрын
It’s just two part epoxy
@johnmacca1967 Жыл бұрын
Nice work mate
@PICHUGIN_OPT Жыл бұрын
Супер!!!🤩
@farmaforpresident8138 Жыл бұрын
Sorry, but I don't get it... Why does the laser only remove the top black coat?😅
@felixchu7656 Жыл бұрын
It's all dependent on the power and speed of the laser. You would have to play around and determine the settings you need to take that black layer off. I have seen some videos where they put multiple layers of paint and increase the power at certain points to remove an extra layer, creating a similar effect.
@farmaforpresident8138 Жыл бұрын
Thanks man, I'll have to give it a try, It looks awesome
@IronCladLaserCo Жыл бұрын
What felixchu said. There’s multiple layers of paint there, you can just kiss it enough to take off the black or you can hit it just right to get off a couple layers in certain spots, has everything to do with under standing your laser, image editing and paint layering.
@ltrick2387 Жыл бұрын
Nice!
@SWAMAC78978 Жыл бұрын
Great Idea! Thank you for this. Also Why aren’t you wearing a painters respirator? I’m a detailer and painter for Automotive, you need to protect your lungs dude. That’s not good.
@IronCladLaserCo Жыл бұрын
I normally do, it was actually lying there, it was hard enough to do the video with one hand and hold the camera. I just didn’t that time.
@mikekiske6 ай бұрын
@@IronCladLaserCo Hi, tehre. Is that epoxy resin? How did you apply the coating? Cheers.
@GokouZWAR Жыл бұрын
So basically you layer paint up on the wood then etch the black paint off to reveal the colored paint below it. Nice. All that black paint dust tho, can’t be healthy to have that in the air…
@IronCladLaserCo Жыл бұрын
You have to get the layers right and the settings so you can burn away just the right amount to reveal the layers under the layers and so on. I have an in-line exhaust fan that pulls it all out and I have a Wyze camera that’s mounted in there and we close the room off while it’s running and can watch from another room on the camera to make sure of fires, we also have the fire suppression system on our M1
@katfire Жыл бұрын
😅its bit just basically....why are u underestimaring the man's art?!!! If u have Heath issues ...masks are available....😊 Excelent job my friend....results are amazing👌
@Ferriscustoms Жыл бұрын
I want see the motorcycles lol 😆 Could you prime it with primer that fill in grains faster?
@IronCladLaserCo Жыл бұрын
lol, ya, my one baby needs a new heart.
@Thanos_Morningstar Жыл бұрын
What pieces of wood are you using? This is cool, im definitely going to try to this. I've been experimenting on canvas too. It's cool to see you doing it. Can you do a video on the canvas? Looking for pointers.
@IronCladLaserCo Жыл бұрын
Thanks, Just cheap precut 2mm basswood from Temu and then two part epoxy
@jffqnn Жыл бұрын
Beautiful Work!! There's So Much to Learn from this Video!! Definitely a Great Idea!! Thank You for Your Time and Video!!
@IronCladLaserCo Жыл бұрын
Thank you.
@nathandrumm9189 Жыл бұрын
They look great!! What epoxy do you use and what is the process? Would be another great video to make.
@IronCladLaserCo Жыл бұрын
Thanks, 2 part crystal clear high quality bar epoxy
@terryh5677 Жыл бұрын
Very nice and ingenious. Wonderful!
@karatohongkongcat Жыл бұрын
Awesome! Need to try it
@ramonhamm3885 Жыл бұрын
The paint doesn't seem to smoke up too bad while lasering.
@IronCladLaserCo Жыл бұрын
It does if I turn off the inline exhaust fan
@misury Жыл бұрын
Great video! Thank you. It did give me slight Blair witch vibe with the camera lol. Perfect for the season! 😂
@IronCladLaserCo Жыл бұрын
lol, ya I totally got that. It does doesn’t it, lmao
@vimcat Жыл бұрын
Your designs are gorgeous! Thanks for the tutorial!
@Pa_Dave Жыл бұрын
so the darker the black, the deeper the engrave?
@IronCladLaserCo Жыл бұрын
Yes
@hooksntoggles Жыл бұрын
What type of epoxy did you use? Would you do a short video on the application of the epoxy?
@Tondizzle Жыл бұрын
This is a great idea! Would love to see how the epoxy process works.
@IronCladLaserCo Жыл бұрын
It’s just 2 part crystal clear high quality uv resistant bar epoxy
@vanessaowens244 Жыл бұрын
Super cool!
@waynesullivan5434 Жыл бұрын
Why did you make the video so damn long. You labeled it changing coil not explaining what's in box etc.
@umutbas86182 жыл бұрын
Hello my Friends has Problem Can you give me Four number
@ryzen3972 жыл бұрын
Thanks for the help, just bought one and its my first mod so this helped me understand.
@tnecniv11242 жыл бұрын
is it safe to chain vape salt nic
@revolversarecool33032 жыл бұрын
How can you get it to unscrew mine is super tight
@PatrickSwayzeOnDbol2 жыл бұрын
Cloth and adjustable pliers.
@amitgupte6922 жыл бұрын
Hi ma'am tfv 8 coil can fixed g priv kit device please reply
@julitaochmanska78112 жыл бұрын
This video did not help me 😫
@ThehoffiONE2 жыл бұрын
Yeah my coil is stuck on the head dont ask me why how can i remove it xD
@archangelrob2 жыл бұрын
I keep ging back to there store cuz my vape keeps on licking how do i make it stop licking for good! 911 plz help me its my first time getting one its a Smok Mag P3!
@carlosmorillon11742 жыл бұрын
Send me one
@raiali23053 жыл бұрын
Can you please tell me How to fix OHMS too high
@Jordan_383 жыл бұрын
Worst coil to change it's so damn hard to get the bottom piece off. I shouldn't have to use a ton of force to remove it.