Rock Awnings.

@METICULOUSGURU thank you some great videos you've helped me out when deciding on products 👍🏻

Coat-it will go over anything.

Yes, but not in one hit if it's a quality wax. Also depends on the strength you use this product at. It's a traffic film remover (TFR) so it's not pH neutral, more alkaline so it will slowly break down polymer coatings and wax's.

If you’re looking to keep the paint in top condition - yes!

Yes. Liquid Clay is the name it’s given for the trade/professional range which can be bought in the larger 5 litre containers. You will need to know an Autoglym Trade supplier to get this.

Robert, I bring it up to 1800rpm (setting 5 on a Flex rotary) for the final. I would have spread the product out at low speed and then brought the speed up to 1800 to finish. I usually set the speed for 5 on the Flex and use the soft control on the trigger to increase the speed gradually as I work. Hope this helps

@@METICULOUSGURU Terrific and thanks for the super quick answer. I assume same principle using a DA polishing machine.

@@robertcurtis6209 Rapid Renovator Plus not really designed for DA but you can get results with it. I mainly used it with the Rotary but have used it with the Flex 3401 forced rotation DA which can gives good results. On a non-forced DA I’m not sure how well it works. The compound needs heat to break down fully to the finishing stage and a DA just mightn’t have enough grunt to do that.

If required yes. Liquid clay will remove most iron contamination. But there might still be tree sap, overspray, tar that you missed etc. Trick is you use a piece of cellophane plastic. Lubricate it and rub it over the paint. The cellophane will amplify the feel of the little lumps and bumps which are contamination. But if it’s perfectly smooth then the jobs done 👍

Avoid windshield, the front one. Side and rear glass is OK. Clean windshield with glass cleaner to remove. Product may cause silicone smear with wipers. But on side and rear glass will give improved wet weather visibility.

Use it neat/straight. You can agitate with soft cloth or sponge.

No.

It is possible - but a lot of work.

You should only reapply every 6 weeks. Beading performance very strong. Use it on my own car and van. Noticeable difference on van cleanliness over waxing.

@@METICULOUSGURU awesome should make a good replacement over the quick wax spray then, and speed up the valeting process too, appreciate the reply.

No, I shampoo them too. Just didn’t bother with that in the vid.

Lol its just another car brand

Just iron.

Try WD40 on tar. That's what I did. Make sure you wash it off afterwards.

No, 'High Foam TFR' is more heavy-duty than Multiwash. The dilution rate in a foamer bottle depends on the flow rate of you're pressure washer - there is no exact science to this. Try a couple of inches in the bottle and see if that generates a good foam. For very dirty vehicles you can add more to the bottle. If you're using an injector system it's between 2 - 5.

METICULOUS.GURU ok mate, thanks for the quick reply

⁠​⁠@@METICULOUSGURU Please tell me the dilution ratio of this product. How much should be mixed with 1 liter of water (high foam tfr)?

⁠@@METICULOUSGURU What is the pH value of this product?

It was washed after. But the result you see is from the foam alone. It's "Autoglym High Foam TFR" you can get it from the Autoglym trade reps.

Tom sorry for the delay in reply, been flat to the mat busy! If you're not getting the result with a product then yeah try something else. Would highly recommend you try the Autoglym UHD shampoo. Really foamy and a good cleaner - all you want for a safe clean.

Yeah spotted that one! Thanks I’ll give it a go!

polperropilot using the new AutoGlym Instadry cloth. Works well.

@@METICULOUSGURU Thank you.

Irek Sawicki well you are supposed to clean it first, and it has nothing at all to do with the fact that it just might be mine 😉🧽😁👍

@@METICULOUSGURU 😂😂😂 😁👍 fair enough budz. Did the same thing this Sunday great product, 4 Budweiser's and 5h later car looked new 😜

TheDct88 it contains silicon which can smear on front windscreen with wipers. Just avoid that area and use a glass cleaner to clear. It’s great on side and rear glass - you get a great hydrophobic effect in bad weather.

If any gets on the windscreen, simply clean with Window Clean or Glass Polish, no problem at all.

Yes it removes iron fallout. The bleeding action is an indication that the product is working and dissolving the iron fallout. It's great on wheels too!

The guys an idiot, its not liquid clay.. Its a imitation Iron X decontamination and fallout remover .. You still have to clay the paint

The guy shows you his application of autoglym liquid clay, not an imitation of anything. It does what it’s meant to do and somehow he’s an idiot is he? Look into the mirror and find yourself tough guy.

Hi. It’s used neat.

no water add on just spray directy .