Elite Box 3.0 and all that worry goes away! 👍

,how hard is it to upgrade from that little 2.0 to the 7.2 ? Also how do you know if the one you have is the 2.0 or the 2.4 ?

Love that cover, the space the box takes up kinda stinks but I need to see it in person I guess. It would be super nice to have retractable as I currently have a tri fold and it's really kind of a pain if I need to put something big in the back but the cover is on I'm pretty stuck. I can take the cover off but it's too wide to fit in the bed without hanging over the tailgate and takes up a bit of room itself and flops around of course. Ugh.

Nice way to loose a few fingers...

You can not over fill a 20, 30, or 40 Pound tanks all of those come with an OPD valve other wise no one will fill them! (OPD means overfill Protection Device) along with that there is an safety release valve on those tanks. Also you don't need a scale once the liquid starts coming out of the bleeder valve it's full.

Those work lights are amazing too

I have the exact same setup,

Merry Christmas Dan!

E p a eco faci st

G o v t mandates this

Ecofacists

Can you have the Pro Power ON while you drive or you have to be stationary? I am thinking on a use case to charge a solar/battery generator (e.g., Ecoflow) while you drive. This way, you can power a small fridge continuously, similarly the way a modern RV does.

So what is the muffler called?

The dirt has to be pretty loose to be able to do most of this right?

Just expensive aftermarket junk , the OEM does its job a true performance engine is a clean engine ( oil and filter ) all intakes work better in cooler weather period and I always use dri filters as oiled filters can mess up sensors starting at the mass air flow. Just buy a quality drop-in filter and save your money.

Very helpful, thank you. It seems what is going on with my constant pressure well expansion tank. Occasional expansion pop sounds and occasional water hammer from air in the system. I bet the bladder has failed.

Grading with a bucket other than backdragging is a futile effort. After 600 hours on my 2038R I’ll only grade with a boxblade. Plus a single rock or root can cost you a $500 balance bar and possible a visit from the local mobile welder to section and reweld the loader that will bend before you have time to react.

forgot to show how the float mechanism works

You got me sir well played

So with this tune on these trucks I can disable the cylinder deactivation feature, but the modes in the truck that it comes with like eco or normal it will remain in v8 at all times no matter what after this tuner ?

Thanks for this video. I really hate this Cylinder Deactivation "feature". You can also disable Cylinder Deactivation in the later RAM 1500 5.7 by hitting your steering wheel mounted gear shift button down once (so it shows a minus sign) then hit the up button to -8. You have to do this every time you shift out of Park. I do it automatically now so it's no big deal. I have an aftermarket exhaust and CD makes an extremely annoying exhaust sound, not to mention it's hard on your engine. Good luck with your trucks y'all!

Ok look, this is actually nonsense, 2013 ford f150 3.5 echoboost super crew 4/4. With 190 thousand miles I get 20.5 mpg long drives an 18 or better in city!!!!! I don’t rely on the computer I do the math an its consist, pulling a heavy load yes it goes down no brainer!!! But to say a much newer model with a new transmission can’t achieve mine is not making sense to me! Maybe I got really lucky! My next truck will b a Chevy ! Because the ford echoboost is very powerful and great fuel efficient! However the maintenance is unreal to keep it running good vrs the good ol v8, don’t get me wrong that 3.5 is awesome, but what I spend in on the clock maintenance per miles what ford requires is much higher in cost vrs a standard v8

In my 2019 I had a folding hard cover and I noticed it was noisy when driving as it flexed with the body of the truck over changing road conditions. Have you noticed any rattles or noise coming from the retractable cover?

Hi. I have a 2.4kw. Can i use my oven range and small freezer just in case of power outage?

Good trainer but I have a small question. I own a 2018 1025R with the loader and backhoe. I see from the video, my bucket is like yours. The cutting edge material is about four inches wide with one inch (bevel) exposed. From the back of the cutter to the heel of the bucket, there is a height difference of about 3/4"; the cutter is proud of the bottm of the bucket. That makes getting a flat track difficult and backdragging challenging. Good hint about supporting the bucket with the tractor instead of just floating it down then unlocking the float. Ballast is ABSOLUTELY necessary!

this is the best video i have seen yet on using a front end loader with a bucket. thanks for taking the time to put this together.

Does this have to be ducted? I want to use it for a dough proofing room and need it to be 80 humidity.

Tune or sport mode, pretty simple...

Thanks for the excellent video. Your place is beautiful! I just mounted this mixer on my Bobcat CT4050. I used my Speeco quick hitch with a hydraulic top link (20-7/8x31-7/8) that gives me up & down control. Leaving my 3-point fully lifted, I find that I have full up and down movement w/o any pto issues. I haven't mixed a load yet, but I must admit I'm disappointed in your stated capacity which is way under the advertised amount. The 350 was listed as having a .48 yard capacity. It's still way better than a wheel barrel, though...

Oh crap I am about to purchase one a 23 should I avoid getting it?

Where are the part list or things needed for us to build? 😅

Tractors require some common sense rare commodity these days. 😂😂

Hello. Can I knew the equipment for this machine? I need for my school project. Thnak you!

This was cool, thanks! Being a new tractor guy I really appreciate it. Although mine is an older model, (1985 Yanmar 187D, ) this still applies.

Thank you. I was looking at getting one for a 2021 F150 5.0 and I think I’ll keep looking. Did you happen to find something that was both quality and preformance?

Very cool design

what size motor did u use?

Why do you place the windrows on the uncut grass. We go the other direction and clean up after the first scalp and again after second scalp.

Just unplug it

What the hell is this?! C'mon.

Awesome! Quick question. Do you think you’d be able to get away with using a smaller electric motor?

you could have shown installation

Just ordered a 2025 STX with the 5.0. Since the truck I ordered in just a 4x2, seems like sport mode is the simple solution and no worries about going into "4 Hi".

You can't even drive a Ford in a straight line withought complications.

I am still rockin that same pioneer receiver to this day!

Thank you for the video. If I go with 1” pipe throughout the house, it looks like that would ensure I have enough, even if I add on an outside grill in the future. My home system will be similar to yours. I’d just rather skip out on reducing pipe size. That would work right? Also, what size pipe are you running from your stage 1 to the stage 2 at the house? My tank is is going to be about 10-20 feet from my stage 2 at the home. Thanks again for the video.

Does that cover come with T-Slots on the rails to mount things like Yakima posts?

Thanks for the tips! Watching you from Kazakhstan)

WOW you do it well. You are a good teacher. Thanks

Will the 2kw Pro Power run a side by side fridge?