Same model as mine. If you look closely at the bottom hinge, you will see it probably bent from door weight and gallon jugs. I fixed mine the same way you did but it bent further so I replaced the hinge with a 90 degree 1/4'" steel angle and cut it to fit and drilled necessary holes in angle piece. 5 years later never had recurring problem.
@SkiBumLee4 күн бұрын
How long is the total time to remove and install? How much time should a handyman charge, that does this for a living?
@ScienceMonkey004 күн бұрын
@@SkiBumLee it took me the day with my buddy. I could have done it quicker if I didn’t remove the siding. Depends on where you live, but i would imagine a handyman would charge anywhere from 500-1000. Might have to factor in any trim work as well.
@jonathanc85139 күн бұрын
is this a right door because it opens from the right ( on the inside) or a left side because.it slides from right to left im confused
@ScienceMonkey009 күн бұрын
@@jonathanc8513 when looking from the outside the left side slides.
@jonathanc85139 күн бұрын
@@ScienceMonkey00 thank you!
@andrelarocque596710 күн бұрын
Used your video to repair my fridge, thank you so much from vermont!
@ScienceMonkey009 күн бұрын
@@andrelarocque5967 great! Thanks for watching!
@user-pd8fs8ib3j17 күн бұрын
installing new sliding doors is always good, but I want to share with you my experience, I live in Orlando Florida, I contacted the Masterslide company with the problem of my sliding doors (if you ask, I will share the contacts) they replaced the rollers, installed a track cover and a new handle with a lock. Now my door is like new and I'm as happy as a child! And most importantly, I thought that I saved more than two thousand dollars! Just because repairs are cheaper!))) so think before ordering new ones. This is not advertising, this is my case.
@user-nd7bk1xt5q18 күн бұрын
I'm about to buy one of these for the west side of the house in a bedroom / sunroom. How are these in winter? Is the insulation good enough
@ScienceMonkey0018 күн бұрын
@@user-nd7bk1xt5q yes, I’ve noticed significant improvements in both summer and winter with this door.
@paulinesnyder141221 күн бұрын
This was the result of participation trophies 🏆 telling people they did a good job when, in reality, they didn't even come close to the finish line. 😅
@ScienceMonkey0021 күн бұрын
@@paulinesnyder1412 🤣🤣🤣
@WilliamDever-g2h21 күн бұрын
Turn the music off and talk. I wanna hear whats going on not jays lame music
@timbamler896422 күн бұрын
You go way to fast and you don't tell what your clicking on
@ScienceMonkey0022 күн бұрын
@@timbamler8964 you slow it down or pause it, and that’s how I design them to be used. It’s a steep learning curve with this program as well, and once you learn where the functions are, you can move much quicker it thanks for watching
@championplayerdo760423 күн бұрын
how did it hold up. nice vid by the way 👍🏾
@ScienceMonkey0022 күн бұрын
Held up great. Don’t have the Jeep anymore, but for a year after no issues
@peppadinero25 күн бұрын
My house was built in 1967 is the ranch so the windows are up high I'm sure I can't even see out of my windows how do I fix that do I lower the windows remove the brick and bring the window down or replace it with new windows
@g37clipsАй бұрын
Had the same issue with my freezer door. I cut a piece of toilet paper tube, folded it couple times and sticked it in the hinge and voila, no more rubbing. Probably not a permanent solution so I'll look into the nylon spacer too.
@clarencejackson5284Ай бұрын
I probably would’ve measured 3 inches side to side and top and put a 5/4 around the outside you doing a good job just a lot of work
@ScienceMonkey00Ай бұрын
@@clarencejackson5284 yeah I made extra work for myself, but it doesn’t leak so fine by me. Thanks for watching!
@bravobooty2107Ай бұрын
This is absolutely bollocks
@AppalachianAmericanWhiteyАй бұрын
Your fault
@thomasbowyer9254Ай бұрын
You turned into him look how much room you gave him from the apex
@MidwesternhighlightsАй бұрын
Learned valuable lesson that day. Pay attn to dad and grandpa.
@user-mp9xu9of8kАй бұрын
Damn I have the same fridge and the same problem, I'm guessing it's common with these?
@ScienceMonkey00Ай бұрын
It seems to be common enough. Pretty common design
@rocketspushoffairАй бұрын
All the measurements are based on a horrizontal flat surface.
@josuefeliciano187Ай бұрын
I use the graco the same machine that you are showing and someone told me to use Dawn to get the paint out of the sprayer and to clean around the machine with the hand moist towel and it does work and Dawn dish soap would also work if your bald-headed like me to take the paint off your head if you're not wearing a cap
@ScienceMonkey00Ай бұрын
I normally just run water through, but I’ll try the dawn soap Idea. Thanks for the tip
@billdesmet3929Ай бұрын
Boxer isn't a racecar.....
@ScienceMonkey00Ай бұрын
🤣🤣🤣
@ryangreen9030Ай бұрын
Do you have a lever on the left side to lift the blades that has a lever with a spring? If so, how the hell do I move it to a higher setting? I can not get it even to the second notch.
@ScienceMonkey00Ай бұрын
I don’t remember if I did on this deck.
@ryangreen9030Ай бұрын
So i get this right, you completely took the mower deck off of the tractor itself
@ScienceMonkey00Ай бұрын
Yes, makes it way easier to do
@ryangreen9030Ай бұрын
@@ScienceMonkey00 actually I just about got it now. I have it off now I have to just put everything back together
@officialgearhead6736Ай бұрын
How is this holding up ?
@ScienceMonkey00Ай бұрын
I actually just started working on it again, so not sure. But definitely seems solid. Motor getting mounted soon enough
@TotalBoatАй бұрын
A drywall sander is a gamer changer! Makes sanding so much quicker!
@ScienceMonkey00Ай бұрын
Definitely is!
@shabetty01Ай бұрын
What’s the material for the extension jams?
@ScienceMonkey00Ай бұрын
Primed finger jointed pine
@joshs3775Ай бұрын
Brooo your lungs
@haydenhammond7395Ай бұрын
Wear a mask man. Save your lungs while theyre healthy!
@germantorres5907Ай бұрын
Great video! Thanks!
@ScienceMonkey00Ай бұрын
Thanks for watching!
@ryangreen9030Ай бұрын
How did you put the belt on the front drive belt??
@ScienceMonkey00Ай бұрын
I believe your referring to when I loosen up the carriage, so that you can tilt it up, around 5:23 in the video
@eaglerider942 ай бұрын
DIY'er here and trying to decide between this model and the Titan 1700. The Titan has a 2yr warranty, if that's a deciding factor. Also, which one has more replaceable parts? Currently Lowes has a discount on the Graco from $369 down to $315 compared with the Titan's regular price of $300. Anyone care to chime in? Thanks
@ScienceMonkey002 ай бұрын
I have the graco and also the inokraft maxpray m1 and I like them both. The inokraft is actually the a little quieter.
@eaglerider942 ай бұрын
@@ScienceMonkey00 I'm confused. Is the Inokraft the Titan?
@ScienceMonkey002 ай бұрын
@@eaglerider94 no, it’s actually another airless sprayer that I own. Didn’t do a full review of it but I use it quite a bit. I have two machines one i dedicated to oil based products and one to water. It’s in this video Parametric Wall from Start to Finish!!! kzbin.info/www/bejne/fnq9iGWkbLaHpLs
@howesinc2 ай бұрын
Almost always need a bigger hammer lol
@neubianx2 ай бұрын
Considering a Z4 platform for Lemons out of Atlanta. How did this work out for you?
@ScienceMonkey00Ай бұрын
Parts easy to come by, light, not many on the track, convertible makes it easy to cage.
@ScienceMonkey00Ай бұрын
Typical bmw problems, larger rotors and calipers would help. We have issues with warped rotors
@neubianxАй бұрын
@@ScienceMonkey00 habe you tried running brake cooling intake tubes to the shields?
@ScienceMonkey00Ай бұрын
@@neubianx yep
@tamerakguner98722 ай бұрын
many thanks
@ScienceMonkey002 ай бұрын
Anytime!
@fixyourautomobile2 ай бұрын
I'm close to fitting 6 Piston 18Z Brembo calipers onto 350mm 5x4.5 rotors from a Mitsubishi Evo X. All going onto a 1999 2wd Ranger with 18x10 Porsche 911 Turbo wheels
@fixyourautomobileАй бұрын
You'll find the Evo rotor is dimensionally the same as the Mustang GT 14" rotor but has a less aggressive rotor offset. It sits closer to the hub center and gave me enough space to slide the 18Z caliper down in between rotor and spindle. I have to machine a massive amount of material out of the spindle, but I use very thick steel bushings to take up the space and allow the M16x1.5 custom length bolts to all line up. (Life hack: Evo X front rotors on rockauto are stupidly cheap for their size and amount of material. The more you spend the lighter the rotors will be once you go into the aluminum hat category. Otherwise they'll be heavy boi's)
@DeagleBingo2 ай бұрын
finishing overlap can help with cutting round holes apparently
@aviiyem2 ай бұрын
Hey, thanks for the vid. I'm about to do the same job. How did it do long term without the alignment?
@ScienceMonkey002 ай бұрын
Thanks for watching. Not to long couple of hours if I remember.
@JCPitboss2 ай бұрын
I got all the parts, wanna come do mine😂😂😂
@ScienceMonkey002 ай бұрын
🤣🤣🤣
@robertavarotto56542 ай бұрын
Hi, HI Can I ask you for help in my onshape project?
@ScienceMonkey002 ай бұрын
Sure!
@robertavarotto56542 ай бұрын
Thank you!!!! 🤩 I'm drawing a lotus-shaped table lamp with the petals that rise and fall by setting the angle with move/copy, I was wondering if it was possible to make the petals rise in assembly with the mat connectors 😬
@ScienceMonkey002 ай бұрын
@@robertavarotto5654 if you want share a copy with me, or share the design with me at [email protected] might be easier to see
@ScienceMonkey002 ай бұрын
@@robertavarotto5654 chat through the email I shared with you, so that we can try to figure this out.
@ScienceMonkey002 ай бұрын
actually check the comments on the file you sent me.
@bernardobojorquez42322 ай бұрын
awesome and very helpful video just used it to start cutting on langmuir xr pro with primeweld cut 60. and worked great thanks.
@ScienceMonkey002 ай бұрын
Great!
@edwardyoung28393 ай бұрын
32MM nut shd be 150 ft/lb torqued at least on GM cars.
@ScienceMonkey003 ай бұрын
Yeah, it’s somewhere close to that for this too. Thanks for watching
@user-gu8br4no4o3 ай бұрын
Amazing, great job 2024 april03my 1st x seeing u ,looking 4ward 4 more ,iam about 2 do some home improvements, just preparing .my . Mind 2 getting started 😅 my favorite it's hard 2 pick it all looks great yeah the frame wall paper took it 2 a whole new level,Enjoy your space,Peace. N love 12:39 pm
@ScienceMonkey003 ай бұрын
Great! Thanks for watching
@oceanstrongchannel91993 ай бұрын
my geometry looks different
@ScienceMonkey003 ай бұрын
How do?
@willie4723 ай бұрын
💘 "PromoSM"
@stevenhaskins16553 ай бұрын
Since the floor is out of level and youvrepair it this way, how do you level the door frame and window frame? I am in a situation where i need to level my floors. I am going to jack the floors.
@ScienceMonkey003 ай бұрын
The windows we reframed, so you would level your sill plate like normal. The front door we had to reframe as well, pulled the header to move it up and re level that as well. It was a process, but it’s what we could do. We jacked the floors up as much as we could before we started creating other issues
@davefranson3 ай бұрын
Damn, that was easy. I was about take the doors off and adjust the tilt. (slotted bracket on upper door hinge of my GE) You saved me a lot of work! Thanks.
@ScienceMonkey003 ай бұрын
Awesome! Thanks for watching
@bertramanderer78554 ай бұрын
Great video
@ScienceMonkey003 ай бұрын
Thanks!
@RuralLifeAndFamily4 ай бұрын
Wait I have a question. I’m a novice here. Where did he get the new corner piece from? Can you buy that?
@ScienceMonkey004 ай бұрын
Yes, check the comments, I posted where I got them from. Thanks for watching
@user-bm9se8xm7r4 ай бұрын
Can you learn some more about audio? It's all over the place. Being in a boxy room doesn't help, your voice bounces off the bare walls, Then you had the double up and you knew it was happening, but you never apologized to your viewers. Finally you moved away from the Mic and was talking away from it. A small tip: Try using a Lavalier Microphone. It should solve most of your problems, they aren't overly expensive unfortunately the only thing it can't fix is you. I'll admit I have a little hearing loss in my right ear, but you tend to mumble occasionally and some of your words get lost, mainly at the ends of your sentences. I guess it could be described of running out of steam. A little speech therapy would definitely help. I spent around 25 years in a TV newsroom and in that time I interviewed many would be reporters and news readers,. Lack of Enunciation was usually a problem, but it was easily remedied by therapy. Don't worry, it's a common problem and you're definitely not the only one .
@quanvon4 ай бұрын
FYI, your videos that use the same introduction have “production” spelled incorrectly. I figure you’re probably reusing things do it’s never fixed 😬 Ignore me feel silly mentioning but figured you may or may not want to fix so your next videos will be correct. Have a great day.
@ScienceMonkey004 ай бұрын
lol. Yes, it was a mistake on my first videos years ago, and I left it on purpose as a lil inside joke. Thanks for noticing and watching!