I put a new intake manifold but it still has the p2015 code position runner on a 2012 VW cc … need help

On 4 minute time in this video you got it. You can take whole thing out when separate brake system from it.

hello. I put this part on an audi a3 140hp 2008, it removed the error on the diagnostics and after a while it appeared again. What's the problem? Thanks

Are the knock sensors in the same place on the s5 CAUA engine?

What is the top speed

LoL at least you admitted it and let us fans learn not to be disteacted listening to radio

Hey brotha awesome video! Did you need to replace the aux fuel pump as well?

1:05 Sounds like post-op adult circumcision pain in the deeyak.

Have a question what if you have already replaced the alternator completely and it's still making that noise could it then be the belt tensioner pulley?

How long did it take the car to get 45 degrees c

The DSG kit I got from FCP with the transmission pan came with 5 bottles so I’m gonna need 2 more?

Most of yall dont know what the problem is but if you look closely on the flapper arm which is connected to the motor has a chipped on it. The arm has a little play on it

Great video

I did mine yesterday. Cant get the wipers to line up correctly now. They either go down to far when in motion or don't go all the way across the windshield (which is somehow cracked.)

Hey brotha did u ever do the boot mode? Is it jus adding a ground into the harness to ground out pin 24 while u boot up? Need to get eeproom from spare ecu to get immo off.

Thank u

They waived me off cause they seen fire🤔🤔🤔 I don't see anything🤷 do you see fire 🔥?

😮

HUGE THANKS brother im replacing all my seals and gaskets and doin the transmission service myself on my 2012 cc. Your awsome!!

Was quoted £980 just this morning to replace both fronts... Watched this video and I am confident I can do this myself and save cash. Thanks for the upload.

Thanks

Audi Just being difficult

If you are in auto zone we used too call that place Auto Hell 😂😂😂

Preach 😂

Hi I have just bought a b5 audi a4 avant, it's a 1.8t manual gearbox and she needs a new/rebuilt steering rack, your video is very helpful I will be attempting this on the drive way tomorrow with axle stands... do you have any more advice please? Thanks for the content and greetings from UK

Lol oh noo

I’m all for making the job easier, less chances for mistake especially when it’s hard to access the timing belt tensioner. My recommendation for anyone doing this job just remove the engine mount and make sure u have a jack with a block of wood up under the oil pan, I believe they are stretch bolts but you can buy a complete kit for like $40.

Why didn't use some sealant on gasket?

What drive shaft?

Is there a way to manually move the blades if the motor is completely dead?

M5 has nitro does it mix with water? I been wanting to try this in my meth injection kit

You don't need the tool. So easy to remove without force.

I'm 90% sure you just tapped into a boost reference for your vacuum. Besides if it is the vacuum side of the turbo it won't work right. The turbo draws more vacuum under boost while manifold vacuum is only present at closed throttle. Vacuum is what assists that style diverter valve open since its not an electronic solenoid like the oem. The turbo flutter is from not having vacuum to open the diverter valve. It was probably acting the same way as blocking off the dv valve

Ty Rawdy Audi

I have a 2010 Jetta TDI manual, and I find it makes that noise at low RPM at like 1200-1800 in 1sg and 2nd … then goes away at higher speeds… What could that be?

I broke the belt and wanted to install a new one can you help me please

did you have to change the fuel injectors I did the same without changing fuel injectors no start low fuel rail presure . just wondering if the injectors are bad

did you have to change the fuel injectors

I can honestly say that that tensioner is good by looking at it. Because that belt is barely moving.

My vcds screen is a little different. I might have screwed up loading injector 1. When I hit change value so.ething came up about export. I hit do it and old and new value went to all AAAAAAA. Now I can't change anything. I can't send you a pix of my screen

Great video, thank you.

the 60 legged alien looking at the screen like how tf u know

Ive got 1. I use it all the time. They even did a limited edition run with Ford Motorsport 1 and it sold off all the vans in the UK and people were tripling their money on ebay and people went mad buying them

do you have to code injectors when doing engine replacement ?

Well done video. Surprised there aren't more comments or views after 4 months. I guess most people are moving away from the 4.2 these days.

Great easy video to follow thanks

Hey brotha thank you so much for all the knowledge I'm your channel quick question. Did you do this step after replacing the HPFP and injectors and priming and coding everything or was this step prior to doing all that?

Horrible audio, hitting the “don’t rec this channel button”

I heard crickets 🦗 haha should have gotten ghe k&n typhoon 🌀 bruh

family first ♥