ihc1974

Пікірлер

@stephenfields6236 4 ай бұрын

Your hand got in front of the camera when you were cutting.

@453421abcdefg12345 6 ай бұрын

That is one way to counterbore the barrel, but why not just bore it in your lathe? It would be much more square and take a fraction of the time.

@aidendelong5869 6 ай бұрын

Thanks for showing me this. Very helpful in my build!!

@oswegonylions12 6 ай бұрын

If this is an operation you have to do on occasion you might want to look into an old school plumbers valve seat reamer.

@Paul-y4d7i 10 ай бұрын

I changed the brake pads and fluid togher

@nigelkavanagh2048 11 ай бұрын

Just getting here now sir! Great vid and very helpful. You get my sub. 👏👏

@Douglas46461 Жыл бұрын

Thanks for blocking the view with you wrist. Great job...🙄🙄🙄

@albertorodriguez9669 2 жыл бұрын

Mecanizar con la fresa artesanal tapando con la mano y el brazo es algo inadmisible

@johnnyholland8765 2 жыл бұрын

I have a Mowery 40 cal just like that one. That mainspring shows imagination...

@johnnyholland8765 2 жыл бұрын

Guess they didn't know what a bottom tap is. I made a tapping set with a bottom tap ground to cut to the bottom of the shoulder. Most muzzle loading barrels are like 1137 which is not real hard and usually cuts easily. Good save and repair.

@danphariss133 Жыл бұрын

I have taps ground to absolute bottom and you can still cut into or dimple the face if not very careful.

@danddiversified8477 2 жыл бұрын

Whoa! Awesome place to be!

@Andy-Gibb 2 жыл бұрын

Why don’t you just use a socket spanner on the end of the square tap. It works better than that set pliers

@johnveglio4433 2 жыл бұрын

ABSOLUTELY BEAUTIFUL !! The skill and art work done is absolutely fantastic. 👍👍👍👍👍👍🇺🇸🇺🇸🇺🇸🇺🇸🇺🇸🇺🇸🇺🇸🇺🇸🇺🇸🇺🇸

@hropanepranks 2 жыл бұрын

Thanks for the flick. My grandfather made that piece.

@alfamale2478 3 жыл бұрын

Next time.....don’t stand in front of the camera My wife tells me I get in the way all the time, and no one wants to see my old farts chicken skin hands...

@deanmacka4975 3 жыл бұрын

Great job mate . Great tip thanks

@danphariss133 3 жыл бұрын

1/2 a FLAT not half a turn.

@danphariss133 4 жыл бұрын

Barrel was poorly breeched by the maker.

@danphariss133 4 жыл бұрын

Had to rebuild a switch in the lathe to cure the click but no run issue.

@tonytonyo879 4 жыл бұрын

Hi Sir, First of all thank you for your channel , it's not a big one but there are some nuggets in there . I have something on the table that i would like to submit to you but youtube doesnt allow anymore to send a message in private , do you have an email when i can describe to you what it is ? Best Regards , Tony

@ihc1974 4 жыл бұрын

I have since found, from someone better educated in such things, that the barrel is a NM barrel. Its also a Colt barrel and slide

Ең жақсы KZbin

Пікірлер