I had to watch it twice to figure out what you’re saying. How do you attach it?

Do you still do these? How can I attend?

I needed this info. Thanks.

Makes sense. I’ve always done compression. Never even thought about it the other way

Flip the braces around. Good as new

Looks self built. "The kit came free, with the gloves.... When I bought the bike."

how well does dry packing work in winter?

My name is Eric and I have engineered a footer that you never have to replace. IT allows you to pull out the post without tarrying out the footer.

Stole that saying from someone else

You're right man, that does look gooder nailed that way

They don’t make this type of hard working men these days. Thanks for the info !

Those fences that are in an angle down the hill. Are they bought with an angle or it’s a type of fence that can move freely to adjust to the hill? Please give me the info and what you call those type of fences. Thanks!

ESTwing, not East. Very helpful video though.

Yeaaaa that looks difficult lol

You mentioned adding an additional compression brace if building a wider gate. With dual 4’ tall gates, 6’ wide, should an additional vertical strut be installed between the two braces?

Are you putting a 3/8 in gap? I’m trying speed up that process for me and also deal with in even warping of pickets. Does anyone have advice on good supplier for fence materials outside of home depot? Their pickets suck

And that's my friends is how fence starts leaning and sinking

I put a temp nail 3.5 inches down from my top string line for the 2x4 to rest on then back mark the rail , same for the bottom.

Run your string 1ft out of grade use stakes run your string to hight by measuring from grade to string set all post to hight.

Ugggghh. I like everything but your posts. 4 x 4 PT wood looks better than metal but in 20 years i turns to blahhh. Other than the 4 x 4's great video.

Clean work.

Wow, within 30 seconds you're answering a question I haven't found in multiple other DIy videos! which side to put the hinge on. Now back to the video.....

Only thing I got to say is ask Google it will tell you these fences are designed to be set if you would like they have aluminum inserts that make them stronger than this no dig system I would only use this system if I had too. Been doing fence for 40 years I can see a lot of things going bad with this system over time. I would also like to add posts don't drive through barriers in the ground like rock big roots it's a good sales tactic but that's all it is

That double picket rip was like magic

Fence posts are usually resting on the ground and the concrete just prevents lateral movement. We don’t need 4000psi concrete for fence posts. All that matters is the posts don’t move. Any other concrete test does not apply to a fence. Too many people are overthinking this.

Awesome stuff I was 262 After this, I charge per section round up

I ordered this 2.0 and think it's a great tool but wasn't able to use it for my fence build yet. My top rails or runners (2x4s) were too high or close to the top of my 4x4 posts so it wouldn't work.. So, my questions are: How far (minimum) is needed for the pickets to be above the 4x4 posts so that there's clearance for the 2.0 to be used? Thank you.

Exactly, but I’ve learned that they can’t weaponize anything you have already taken ownership of!

the only upgrade i could see is rather than having battery holders you should have that for an on the truck charging spot #nomoreleftbehindchargers

what nail gun and nails are you using.Thanks

Badass hat🤘

brother you are a wealth of knowledge on anything fence related

The angle is in the wrong direction

Looks good One question for you what size table saw do you use for ripping pickets and what blade. Do you install the blade backwards.

Gaps. 10min a section i can make a panel in less time and it's squeezed tight. And you don't have to build on-site. Just install

Loved your video, but seriously could you do a video, running full speed and making it, in one minute?! I would love to see that happen sir! Or if there is already a video of you doing it in one minute please send me the link

Is the tension bar required for 4' gates?

Great Video!😇

What tool are you using

What’s the make and model of the nail gun you’re using? By the way, your work is excellent!! Thanks

Where are you based out of? I am looking for ideas for fencing in my 5 acres of property but I am also on a hill so some is rocky. Please advise. Your videos are great!

@1:59.....Id have his head on a platter if he tripped and broke that line😂

Love it! Great job

Shoot, wish I'd watched this. Flaring the bottom is a great idea. This guy is the fence master.

This is great info; you need to come to Bradenton/Palmetto/Sarasota, Florida because every fence company (even the largest companies in our area) are building their gate braces wrong!

What tool and blade size was used to cut?

OSHA here, no need for that useless plastic helmet.

The rack in it looks like SHIT.

Why are your gates crowned and not straight across??

How about fixing those runners first