Mine spins. When washing I can not see soap and water. Lacking water a lot. Since is also bad. Then spin on max can't spin much faster then washing. And keeps stopping

My Washer Grinding noise and won't spin... , when it spins i heard a sound like grinding motor a little bit, and it stopped

Really appreciate you showing me how to access the LG washer Auto-Diag test!!

shit bag

thanks for the video, in case mine needs a control board, do you know where I may be able to get one? Thanks

Have same exact washer. When i do diagnostics mode stays if81 after i hit start an washer keeps going as it should . Will that show me what is bad if i let it run? Im trying to figure out why it washes the whole load ,drains water but wont do final spin cycle an keeps throwing Ue code. So far replaced lid switch,hall sensor on stator an waiting on tub to pump rubber hose thing to come next. Even open the plastic enclosure around the drum to see if anything was in-between the walls.any help is really appreciated

at 3:20 you had voltage, 110ish and 130ish, why do you say you had no voltage? do you mean you didnt have enough voltage?

This is one of the best and most informative videos on the internet. Especially in regards to actually testing parts to ensure you have the problem correctly diagnosed. I didn't need the parts mentioned. However it helped me diagnose a break in one of the wires within the wiring harness. It was a big help and saved a lot of time guessing at the problem. Thanks for taking the time to make this video.

Why didn't you show where to go all the terminals back up

ok.. what if the control board is working and motor spins but drum does not

The reason I went to test mode in first place was bc the drum never spins during any cycle

No I went to that test mode, and when I pushed the play button to lock the door, the drum began spinning at 50 rpm, but when I pushed it again, it stopped. What does THAT mean?

👍

The first thing you do is put the machine into diagnostic mode to see if the motor runs and if it kicks any error codes. Don’t dive in immediately.

When I try to enter diagnostic mode after if:81 when I press the start button I get “be” code and it will not do anything else. What does this mean?

Very well and easy to follow tutorial video! This video was very helpful in repairing this machine!! 💯 % recommended

Cleaning the water filter on a front load lg washer

Unfortunately I got new control board and spent 300 wasn’t the problem. It was the drain pump.

Great video anybody got a link to the new board?

Made my brother's work. They were about to call a mechanic. Needed to drain it manually. Awesome work!!!!! You nailed it mr scott

Good evening sir, my name is Peter from Egypt and I am a technician in electronics and I am happy with your explanation because I learned a lot from you Would you allow me to be a friend to learn from your experiencesAnd I encountered a strange malfunction in the L.G washing machine. The malfunction opens water without closing And I unscrewed the board from above and took the measurements and found that there were shorts on it And I installed the board again, but the defect exists. What is the solution? I listen to your advice I forgot to tell you that I changed the level unit and the hose, and the defect is present

So how do you get a new control board

Thanks

🄿🅁🄾🄼🄾🅂🄼 🎶

My Frigidaire front load washer not spin at all j had replace control broad still not spin ,it has a motor protector but I can not found it , could you help thank

My 212kwat5u504 LG washine machine won't drain. It spins but won't drain. I removed the motor pump assy, applied 120VAC and it pumps. There is no blockage in the hose or the filter. Control board maybe?

When I set it to diagnostic mode it begins to spin. When I try to put apply a wash setting it will not spin

“No voltage” - but literally showing voltage.

Why don’t you answer peoples questions? 😕

Please help 😫 I tried everything to unlock the child lock for the last 8 hours!! Finally checked you tube and solved the problem! However, in my own attempts to fix it earlier, I pulled that little hose out of the little compartment down the front of my machine to drain any excess water, and pulled too hard and snapped the bloody thing! Is there a way for me to reconnect that hose? My freshly painted laundry is now flooded due to the water just pouring out the bottom of the machine, all over the floor 🤦🏻‍♀️

Can I still get the ECB?

llppp

How you get new terminal ? Mine is wm800h*A lg my problème is clean well the cloth but not spin to 11 minute poof to 1 and close him self

Same washer. Any idea what would make it work mostly normal. But spin super slow and then after awhile of slow spinning it just fails .. What would make it spin slow as the only symptom

My machine is different version where do I press

Low Voltage not NO Voltage...

Thank you for the video. My washer is not a year old yet, but the spinnig is stuck on 6 minutes. The information in your video is great. You just gained a new subscriber.

Now u in clóset donde jamás te veo

In

Thanks

Thanks

Where is the vibration sensor ( out of balance sensor), caused by bad shocks etc on these machines?

Very well done, excellent. Clear, good pace, good approach and filmwork. Thank you.

I replaced the worn-out bearings and seal then got this problem on a WD 12397 TD. I got help to carry out tests including this one to see what was the problem and we agreed it must be a problem with the motherboard. I was expecting a problem with the position sensor but it turned out OK (the method was from kzbin.info/www/bejne/nYeXXmWibpiNsKs) These motherboards are not available from the LG service in my country. Took it out to an electronic technician who identified and soldered the faulty part of the circuit. Took it back and reinstalled the repaired board on the machine. I held my fingers crossed since it appeared to be a simple fix. Put in on and set it to rinse. The machine is as good as new again. Thank you so much for the clear video.

LG washing machines are trash. Avoid.

Very smart guy.

Lol where’s diagnostic mode #11

please make more video for appliances . how to check the door lock . thanks

More repair videos

Same washer issue but my terminal wire is reading 11.2-11.5ohms on the first step test what dose that tells as your shows reading 7.2-7.5ohms