What is the purpose of this?

great video on how not to do an under deck system all of zip screws not for treated lumber and all the aluminum trim cant cover treated lumber it will corrode. says right on the box .

Mine is being installed today. However, I do have a sunscreen. I'm interested on how the drainage turns out. This would have been a good one to record.

what kind of ceiling system is that?

Not pressure treated any more.....beter treat it...i wouldn't do it.....

What is the water shed ceiling system?

Video not clear enough to see how it's overlaps

9 years later you have taught me something im sure my grandfather has shown me when i was too young to know i needed to care. thank you from someone who has no "adults" left to ask for help.

Good tip, but if you are on 16" deck joist centers...that would be a bit tedious. Guess it's best to do it righty the first time lol

excellent.

Pretty dry under that deck!

Is This Material Aluminum? Is there any concern there will be corrosion do to the treated lumber being on the aluminum? For example where the overhang is that is touching the treated frame.

Are they water proof no no leak and where did you get these ?

I’m about to do this with my track saw. I think it will help cut a nice sharp straight line. Thanks for the video!

Why does mine keep bowing in the middle?! Grrr

Just did a 20 x 20 deck using this technique this past weekend- some fool not only set the boards too close they also caulked the joints.

I tried the tool with one blade on a 20 yr old deck with 2x6 ( not 5/4 thick) boards. Many of my boards have zero gap. I could not find documentation anywhere else saying it is OK to double the blade. I may go back after I have cut a single blade gap with a double blade. I was ok using a plunge cut to start the cut….get the blade up to speed before contacting the work. The main issue I had was having zero gap there is nowhere for the front guide to go. I cut it off and just kept the rear guide and blade. It easy to gouge the boards but

what type of material is used here?

Don’t wreck your deck doing this

well that looks terrible.

I burnt my porter cable circle saw up trying to do this. I’ve had it for years so it may have just been it’s time to go.

Love it ! Nice clean look !

Not much info on what the panels are or where to buy.

Has anyone use the "saw guide" by Lounsbury Products? $16.95 I am considering ordering this.

Looks like magic

I discovered that our vinyl is fastened to 1x3 wood slats with roofing nails. Can’t be detached without damaging the vinyl.

How did he remove the nails?

This looks awesome!

Incredible work. Thanks for the instruction. HOWEVER, I have a suggestion. If you watch those HGTV shows, you'll see that they spend a good chunk of the show going through and showing the finished product and reviewing everything that was done. Your great work could have used a bit of that. I felt like I was barely able to admire the finished product - which was really worth admiring. Those shows also review before and after images to really help underscore the great work that was done. Add a few more things like that in the future and then just keep it up! It's really great. Thanks for the information.

What is the purpose of this flashing on the bottom edge of the ledger board?

Would love to see the reverse of this, replacing with the new section. I can't believe it would be that easy. This looks doable but not yet convinced of being able to get the new one back in its place.

I’m more curious to know how this deck is attached to the brick veneer.

Never have scene this flashing is this code ?

A close up of the tool and what it’s doing would help. I still not clear on this. Mine is bead-board though.

I'm wondering how it works if you plunge cut into a gap when you can't come at the cut from the outside. Any chance of kick back or saw getting stuck. Also, anyone recommend any "Fence" that could hook into the groove to help keep the cuts straight?

Seek the Lord and saviour Jesus Christ before it's too late. John 3:16 “For God so loved the world, that he gave his only begotten Son, that whosoever believeth in him should not perish, but have everlasting life.” Hell is real and Heaven is also real. You don't want to spend an eternity in Hell torment without God. The only way to escape Hell is to follow Jesus Christ our Lord and saviour. Study God's Word the KJV Bible to know more and pray and seek until you find Jesus. Tomorrow might be too late. Next minute is not promised. Do it now.

looks awful. now you need a router.

What happens if i use a blade with 20 teeth and one with 24 teeth?

Licensed electrician used romex for an exterior application? You might consider another electrician. ;)

You lose the radius edge of the boards. That’s going to look really bad.

It's easy to "go off course" and mess up the edge of a board when doing this (like was done in the video)

How did u make it to slope?

Thank you six years later. Helped me a lot

good

this is good. like F linear ceiling but a little diffrient

very nice

There is no bushing. Fuck handymen.

Is there a reason you ran the wire between 2 panels? Why not go in the middle of 1 panel ?

Any videos available for a screened in area ? How does it install around the walls ? Thx

When did you install the G channel ? Did I miss it ?