MadAtTheSky

Пікірлер

@piecola2 2 ай бұрын

your system is beautiful! have you published the project so you can replicate it? I'm not an expert, I'd like to have an FPV plane to shoot like yours!

@madatthesky7588 2 ай бұрын

Thabk you for the kind words! I have not published anything, but I do have a notebook with the schematics drawn out and a lot of notes I took while constructing the setup.

@crawford323 2 ай бұрын

Is this adaptable to a quad drone system such as DJI?

@madatthesky7588 2 ай бұрын

It would take considerable modification to work with DJI systems, unfortunately

@crawford323 2 ай бұрын

@@madatthesky7588 what drone system capable of quality video is adaptable to joystick controls other than DJI

@madatthesky7588 2 ай бұрын

Excuse me, I take back what I said previously... you could theoretically open up a DJI controller and wire into the gimbals and switches like I did with the Taranis. The DJI transmitter would of course have to be modified. Sorry for my confusion

@neiljones4287 3 ай бұрын

Might as well just fly a simulator don’t you think?

@madatthesky7588 3 ай бұрын

If you want simulated flight. This is a little more immersive and it's fun to build and fly the actual aircraft

@user-kp3fw4zd3c 6 ай бұрын

how did you connect all these things together? any tutorial video?

@DontEverGrowUp 8 ай бұрын

DartXL, 7000mAh 18650 pack, F722-WING flight controller running INAV 6.1.1, 1.2GHz video link with Pepperbox V2 antenna on the ground, and Crossfire for control link using a TX16S transmitter: kzbin.info/www/bejne/f5e6oJqvnsufhaMsi=uEw6Xfac_rb3e6Od

@wandersonmiranda6680 Жыл бұрын

Mais ser quiser copra esse controle para bota em um projeto como fais

@neilcaywood3803 Жыл бұрын

All I can say is wow! And thank you for sharing.

@KnightsForChrist. Жыл бұрын

is it possible to fly an FreeWing F-22 Raptor 90mm or a turbine conversion of the model to those distances with the same setup you have here

@madatthesky7588 Жыл бұрын

I do not believe so... this plane was specifically built for this flight and I custom made the battery pack myself for this

@Chris-pg9ex Жыл бұрын

@MadAtTheSky Could i do this with any receiver? What fpv system did you use If you could answer these that would be great.

@madatthesky7588 Жыл бұрын

It's actually the transmitter that is modified, but yes, any transmitter will work. Some are more difficult to do this to than others. I used a FrSky X9E because all of the controls were tied to the circuit via connectors. I unplugged the connectors and wired in external connections so I could reconfigure the transmitter back to its original state if I wanted to use it as a traditional transmitter.

@gcl_2000 Жыл бұрын

Hi very nice setup. Any build details? Thanks

@madatthesky7588 Жыл бұрын

Thank you! I really wish I would have done a better job documenting the build but after I started on it I just kinda went full steam ahead until it was completed. I can answer any questions you may have about it though.

@gcl_2000 Жыл бұрын

@@madatthesky7588 Thank you. i'll ask when i also have time to do one. Big thanks

@gcl_2000 Жыл бұрын

@@madatthesky7588 so basically you just tap the wire from the stick controller in the transmitter to the potentiometer of the joystick, is that what you did?

@madatthesky7588 Жыл бұрын

@@gcl_2000 exactly. I opened up the joystick and soldered wires from the pots to the inputs of the transmitter where the sticks would plug in

@gcl_2000 Жыл бұрын

@@madatthesky7588 thank you very much

@jimmytheriot8978 2 жыл бұрын

Check out my homemade fpv cockpit with the dji and axis flying HD box hooked to it like share and subscribe !

@likeabird-innovativesoluti5042 2 жыл бұрын

Hi! I made a plug & play solution instead of hard wiring: A simple USB2RC box with Head Tracker input too. Here the uncut video. Sorry, forgot to insert the SD card in the goggles for FPV recording... I'm getting old... ;-) kzbin.info/www/bejne/gpCVYqVsrd9lqtk

@blaine2575 2 жыл бұрын

I am very interested in your plane for sale

@madatthesky7588 2 жыл бұрын

What plane?

@blaine2575 2 жыл бұрын

Your PA Addiction XL Dan. 206-427-4245

@blaine2575 2 жыл бұрын

Sorry. Wrong party

@blaine2575 2 жыл бұрын

Sorry. Wrong party. Please delete my comments

@BaqPaqJaq 2 жыл бұрын

Nice video of the ruins. The setting sun and long shadows give it great atmosphere! I’ve been droning some abandoned ruins too: kzbin.info/www/bejne/n2rbfJuLo5ppbas. I’ve left you a 👍🏻 and subscribed. Jackie

@joefuels1 2 жыл бұрын

any updates on the build thread?

@madatthesky7588 2 жыл бұрын

Soon!

@cobra4829 2 жыл бұрын

did you figure out why you had video quality loos? for me it doesn't look like going out of the antenna beam I had a similar problem with RMRC receiver and after some time it died completely

@madatthesky7588 2 жыл бұрын

I never did find out the cause because it never happened again. Maybe the video transmitter got hot or the DVR/groundstation voltage got too low.

@mango9cloud 2 жыл бұрын

Good job 👏

@madatthesky7588 2 жыл бұрын

Thanks buddy!

@flightlieutenant6902 3 жыл бұрын

Great ideas mate . Very educational. Cheers from Australia. 🙂👍🇦🇺🇦🇺🇦🇺🇦🇺🇦🇺🇦🇺🇦🇺🇦🇺🇦🇺🇦🇺

@madatthesky7588 3 жыл бұрын

Thank you for your support!!!

@flightlieutenant6902 3 жыл бұрын

@@madatthesky7588 no worries mate , hope to see more of your videos . . cheers from Australia 🙂👍🇦🇺🇦🇺🇦🇺🇦🇺🇦🇺🇦🇺🇦🇺🇦🇺🇦🇺🇦🇺

@thibd5645 3 жыл бұрын

Hello ! Nice video, can you explain how do you have interfaced the joystick with your system ?

@madatthesky7588 3 жыл бұрын

Hi! I essentially hardwired the joystick to the motherboard inside the transmitter. I made it modular by installing D connectors to the case and joystick to make transport and troubleshooting easier.

@crossbowmotors8368 Жыл бұрын

@@madatthesky7588 Could you possibly share exactly how you hardwired the joystick to the controller motherboard?

@GUARD14N Жыл бұрын

@@crossbowmotors8368 He wired the potentiometers and switches from the joystick to where they would natively be on the transmitter. Example, the pitch and roll axis potentiometers on the joystick would be wired to directly to where the pitch and roll normally go on the transmitter motherboard. Same for the switches. Hope this helps! Best of luck!

@SomeTechGuy666 3 жыл бұрын

How did you interface the joystick and throttle into the X9E ? Analog ? You took the voltages off the external controls and fed them into the X9E motherboard ? Do you have a build thread for this setup ?

@madatthesky7588 3 жыл бұрын

Hi, yes all analog. I hardwired everything through D connectors to the motherboard and just calibrated the joystick and throttle through the calibration screen on the radio

@madatthesky7588 3 жыл бұрын

I do not have a build thread but I'm building another setup and make a thread from that

@SomeTechGuy666 3 жыл бұрын

@@madatthesky7588 I'd like that. Do you realize that you could attach the signals from the throttle and joystick via USB into an RPi and then feed the signal into the transmitter via the trainer port ?

@madatthesky7588 3 жыл бұрын

@@SomeTechGuy666 yes, I originally looked for a USB to ppm converter but couldn't find one so I just rigged this up. It was a little time consuming but otherwise pretty easy

@SomeTechGuy666 3 жыл бұрын

@@madatthesky7588 I saw some projects on git a while back. I'll see if I can dig up some links for you. Would save a lot of wiring to use USB instead of analog. But I understand why you did what you did.

@ElvinYX 3 жыл бұрын

Sir what battery did you use? And how much flight time can you get?

@madatthesky7588 3 жыл бұрын

Hi there, I used a home built 14.8V 7000mAh li-ion pack. I can get an hour and 20 minutes of flight time with it.

@ElvinYX 3 жыл бұрын

@@madatthesky7588 that's awesome! Thanks!

@aaronblodgett2825 3 жыл бұрын

What a pilot!!! Way to go buddy!!

@madatthesky7588 3 жыл бұрын

Thank you man!!

@DontEverGrowUp 3 жыл бұрын

It was nice meeting you out at the field today. I'm the guy with the green phone. :-)

@aaronblodgett2825 3 жыл бұрын

Hey Garrett..its Aaron ...i just subscribed! Awesome vid!!

@madatthesky7588 3 жыл бұрын

Thank you man!!

@mitchellroberts7954 3 жыл бұрын

I have to wonder why you're drawing well above 5a at some points at cruise? Doesn't seem efficient.

@madatthesky7588 3 жыл бұрын

It's because the autopilot was set to cruise at 45 percent throttle, it's been changed since then and cruises nicely at 4A

@markgiles8527 4 жыл бұрын

Hey, if i wanted to fly a multi rotor (a dji f550) around and out to about 4 or 5 km. Do you think 2.4Ghz would do the job? I see you mention you are using 1.3Ghz. I've been playing around with ezwifibroadcast. Have you bothered to look it that?

@madatthesky7588 4 жыл бұрын

Hi there! I'm sure 2.4ghz would get you there! I haven't checked out ezwifibroadcast yet