I just watch a video of a tech stating where the grease fitting is normally placed. He said the same as you, but the problem is he said, "I'll let the customer know that he needs it installed so the throwout bearing won't dry out." In reality, all he had to do was look for it. I'm so glad I found your video because my clutch has been kinda sticky. I wonder how many other techs have no clue where the grease fitting is.
@jorgefacio6902 ай бұрын
whats the recommended height???
@BrackishMongrel2 ай бұрын
You want to keep the top of the frame rails close to even with the top of the tires
@truckingwithcliff2 ай бұрын
Excellent video
@andersonpereira43093 ай бұрын
Yep, thank you, Accountability at best.....
@vicpetrishak77053 ай бұрын
Do not cut the suspension rod . Check to see if the differential rod bracket is bent . Remove rod from air valve bracket arm . Chalk Steer tires and release parking brakes . Adjust air to air springs , bring frame level across the tops of tires . Place golf tee through air valve bracket into valve body . Connect rod to bracket and tighten valve , remove golf tee .
@oraliaornelas57424 ай бұрын
Well they do charge a core.
@BrackishMongrel4 ай бұрын
Not in my experience they haven't
@esteban92504 ай бұрын
Good video 👍
@firematter25327 ай бұрын
I found your video too late , I had to change my clutch , , now I know😆 tank you
@BrackishMongrel7 ай бұрын
Bummer... sorry to hear that. At least you know now and can keep up with it moving forward.
@thisiskingone7 ай бұрын
That is called famen 😂😂😂😂😂 you need care
@semperfi2838 ай бұрын
What's the code? Always give you the codes.... Thanks
@steveerpelding64158 ай бұрын
Just changed one on a 2016. $400.00 but I got a $100.00 core charge back. So It was $300.00.
@blakehalley32549 ай бұрын
Doesnt a remote throwout bearing have a cable that goes from that fitting to the chassis near the bottom of the fuel filter? If so, how much grease do you put in the cable? Do you pump it with grease until it comes out of the top of the cable?
@BrackishMongrel9 ай бұрын
I'm not sure what you are referring to. The throwout bearing is on the input shaft of your transmission. Most are actuated via a hydraulic or mechanical linkage, and to my knowledge there are no cables involved in any application. Perhaps the "cable" you refer to is a grease tube? In that case, I suppose it could be located anywhere on the truck, and you could just follow that grease tube to the transmission to know which one it is. As far as how many pumps of grease, you only want to do about three pumps every 50k miles. Any more and you can get grease on your clutch which could cause problems. Hope I answered your question.
@johnysilver18539 ай бұрын
Thank you for the information
@MadTruckaYo9 ай бұрын
Should the shaking in the rear be intermittent or constant. I have a shake in the rear and it comes and goes
@BrackishMongrel9 ай бұрын
I get that too. Sometimes it is the trailer that I am pulling, but I think overall it's a combination of worn engine mounts, suspension bushings, tires out of balance, etc. Any number of things. I don't think it can be nailed down to just one thing. My truck has almost a million miles, and I'm learning to live with the fact that it's not new anymore. So if your truck has a bunch of miles with original motor mounts and suspension components, it's probably all of it together when it comes and goes like you're describing.
@roz474710 ай бұрын
So it was a little more than 2K it’s going to be about 5 1/2K apparently I let it run low on gear oil. It had a slow leak which I thought was engine oil, is what I get for thinking……..
@BrackishMongrel10 ай бұрын
Oh crap, so you need a new transmission now?
@roz474710 ай бұрын
@@BrackishMongrel yep, found a used one in northern Utah. Rented a truck drove 80 miles there picked it up came back dropped it off at Caterpillar the next night they finished up. What a fun experience out on the road!
@roz474711 ай бұрын
Thanks, I think mine just cost me 2k, stuck in Pocatello ID………
@BrackishMongrel11 ай бұрын
Sorry to hear you are having trouble. I hope you're up and running soon. Take care
@DONTCALLMETHAT11 ай бұрын
I cleaned mine once before and it worked until recently. When I cleaned mine I had only limited tools. I'm gonna soak mine in diesel while I'm home. Also mine is from an 08 Western star With Detroit 60 series 14L
@DONTCALLMETHAT11 ай бұрын
Point me to where I can pay 400$ for one. Mine is purging oil
@BrackishMongrel11 ай бұрын
I bought mine directly from Freightliner. But before you do that, there was someone who commented that he's had success using oven cleaner. I never thought of that, so it may be worth a try.
@johac763711 ай бұрын
I have cleaned them with old fashioned stinky "oven clearer" the original, corrosive stuff, I wash it with solvent, diesel, even gasoline, then pour the oven cleaner in, plug the hole and shake it, depending on how dirty it is, 2-3 times, then rinse with hot water til clean, I've tried every snake oil, Seafoam included, hot, cold, nothing cuts the residues of blowby, oil gum like oven cleaner. Word of caution, don't leave it soaking for hours, it will etch the aluminum., I've boiled stuff in a big slow cooker with TSP, original nasty stuff, it's almost like the old outlawed hot tanks for effectiveness.
@BrackishMongrel11 ай бұрын
Interesting. Good to know. Thanks!
@funtarig Жыл бұрын
Helpful video ❤👍🏾
@adrianiorin8896 Жыл бұрын
They self adjust,problem is they go bad
@BrackishMongrel Жыл бұрын
Yes, they do self adjust, that's their whole purpose, but they are still manually adjustable at the valve itself to raise or lower the maximum height.
@spencerwillis7578 Жыл бұрын
Appreciate it... Guess I'll go ahead and pay the money 😩
@jasonlittle7697 Жыл бұрын
Agreed 👍
@briankeefe6161 Жыл бұрын
Thank you sir since I don't weld I'll try your idea first be safe out there driver
@virtualrelaxing5155 Жыл бұрын
Great video sir! Of course Freightliner will not make it reusable 😂😂😊
@willmann30 Жыл бұрын
YES. I think I need a clutch and input shaft. The amount of noise when the clutch is pressed in is insane.
@BrackishMongrel11 ай бұрын
That's never good. Sorry to hear about that. Hope you're back up and running
@realskata1610 ай бұрын
What did it end up being
@jeancadet5862 Жыл бұрын
What kind off truck you got
@BrackishMongrel Жыл бұрын
2015 freightliner cascadia
@RadeStevanovicSrem Жыл бұрын
Short, and straight to the point! You should keep doing it this way! EXCELLENT!!!
@Savageking0000 Жыл бұрын
Yes it was! All the other videos just gave me a headache
@harpreetsingh-sd2vb Жыл бұрын
Use full information
@therainmaka6455 Жыл бұрын
Cool brother thanks 🙏🏾
@BrackishMongrel Жыл бұрын
You bet
@AmarjitSingh-ql2uv Жыл бұрын
Thanks a million brother 👏🏼👏🏼👏🏼👏🏼
@BrackishMongrel Жыл бұрын
Glad it helped
@JS-jv6rg Жыл бұрын
You nailed it, this is the correct way of doing it.
@sofistk8ddd1 Жыл бұрын
What is the height supposed to be at and will it change when empty or you have a trailer attached?
@BrackishMongrel Жыл бұрын
I've always set my height to where the top of the tires, (assuming they are 295/75 22.5's) are even with the top of the frame rail. And yes, it should be at the same height loaded and empty. That is the purpose of the leveling valve. It adds our removes air from the suspension to maintain a constant height.
@josea.ortega1431 Жыл бұрын
Good info man thanks
@BrackishMongrel Жыл бұрын
No problem 👍
@kevincolson5609 Жыл бұрын
Thank you brother! Best explanation yet!
@BrackishMongrel Жыл бұрын
Glad it was helpful!
@lizzysbeautyshowetc.68952 жыл бұрын
You should stick to this topic you're better at it than commenting on president Biden you make asinine unconherent comments that don't make any sense
@BrackishMongrel2 жыл бұрын
Thanks for the compliment! What's uncoherent mean? You mean incoherent? Now who's UNcoherent? 🤣🤣🤣
@rss6082 жыл бұрын
yes, first vid that explained the elongated slot adjustment method. excellent
@elwaters46352 жыл бұрын
Thank you buddy
@buzzbustillos30162 жыл бұрын
That is a great video.
@dragondesert11342 жыл бұрын
Thanks man ❤️
@jocelynquintal27102 жыл бұрын
Bravo amazing smart ...wow it easy and change all the ride
@deliusfrazier26852 жыл бұрын
Thanks for the information
@ryannewton47662 жыл бұрын
What is the height suppose to be at?
@Serta2302 жыл бұрын
I figured that top of the 2 axle wheel is supposed to be lined up with frame when u look at it from the side,worked for me.Good luck
@thowguandong3076 Жыл бұрын
@@Serta230 can you do video about I still don't understand
@thebigboss18392 жыл бұрын
I need to raise m my suspension a little bit so I would move the valve slightly up? Or down ?
@BrackishMongrel2 жыл бұрын
You would want to move the valve down a little
@bennyhall74442 жыл бұрын
Awesome video brother very very helpful please make more your a natural born you-tuber