😊

Do you have link to the kit?

Hey, is there any way to bypass the I guess ignition coil the part that connects to the spark plug

Hi, do you know why after replacing the clutch the back wheels will not move when I push the bike , when I push backwards they turn but forward seemes locked. Everything works fine when driving.

спасибо, было интересное сравнение

I've oil leaking at the stator side Can you advise or help please?

I got my son an Apollo 125 rfz 20 max…. Can anyone steer me in the right direction for a 22 or 26mm carb?

4:30 bro had me feeling some type of way😂

would this work on the Coleman 125 atv?

Williams Karen Taylor Patricia White Paul

Great video

How long will my bike run will I blow my engine if the fan don't run or what

I recommend hair spray instead of wd40. Hair spray dries fast and is a little sticky

Stop using a screwdriver to pry the cases apart 🤦

Just picked up a 66 and 2 67 ct90 that has not been cranked in over 30 years. 100 bucks for all 3

Too far away!

Lot more he jams

Hell ya man think u known what you are doing

Hey brother. I have 2 Apollo bikes...where did you get the transmissions from...so hard to find.very frustrating...would love some help...BTW enjoy your videos..happy subscriber here😊

Did you look at the crank shaft position sensor

How to do the timing?

Mine smoked bad at first start up for the first 15 mins after my top end rebuild. I don’t know if it was the new rings took a bit to finally seat, or if it was all the oil I used oiling things down on assembly. I put oil on my rings in around the piston, and I coated my cylinder down with oil when assembled it. John Talley on Partzilla said to, so I did. He’s the man. If he says to, you do it lol. I was freaking out mad at first tho then it eventually stopped once it all burned off.

Iweu

PE26 Nibbi carb + 140cc engine swap on a 125cc pitbike frame puts in work...💯💯 With a 17t front sprocket and a 428 37T rear sprocket /powercore 2 exhaust slip on 👍💨💨

For my expirience nibbi carbs are better BUT u do have to understand. Needle adjusting, air intake and exaust. But for easy fit mikuni

where can you get a new spring

Get the 22mm 26 really ain’t meant for pit bikes

So I took my dirtbike mudding and in the middle of the mud my dirtbike turned off and hasn’t started since I took my whole dirtbike apart dumped out all of the gas took my nibbi carburetor off cleaned it and I took my engine off and took the engine apart drain all the oil and then I put everything back together put new oil in it and new gas and it’s still not starting and now there’s something leaking out of my bike and idk what it is and it still won’t start and it has compression but not as good as it should do you know any reason why it wouldn’t be starting still or what would be leaking out of my engine?

The Mikuni sucks compared to the 22mm Nibbi on my apollos

what a great video my friend. trying to solve a no power issue to the kids quad. This helps me immensely. thank you

I got to have one of those impact screwdrivers. Nice.

Good Video 😎

Nothing on adjusting it when first get one of these bikes because I didn't start mine yet an when I pop it in first hold in the clutch it's real hard to roll it when I pop in neutral it rolls fine n dandy

Is this bike a two or four stroke?

Looks like you have every step memorized including proper sequence.

I use the carburetor from nibbi that you just bolt right on same fittings as the mikuni and it runs better than any carb I've gotten to work on my bike, I do have a mikuni carb but i could never get it to work on my bike

I'm having an issue because my ignition was also wired to my headlight can u help?

do you offer rebuild service lol i need you in my life

🔥👍

Hey, I need some help. I can’t get the brake pads to release.

im getting a genuine mikuni carb

I know it’s an old video but where did you get your gasket kit

3:47 The slow turn and look at the dog to tell em to be quiet lowkey hilarious

I’ve done everything the video says and it clicks, but the dots are lined up?

I cant find gears for a 250cc anywhere, are these all the same?

Watch your ears at about 14 mins. Dude should have edited out that high pitch scratching. hurt my damn ears......

At 19:49, what is that thing next to the hole where the shofter assembly goes into? Mine seems to be missing that but has a hole for it, thanks

How do I know if I need to replace the clutch mine is making a rattling noise towards the top of each gear help pls

is this a 54mm bore motor or the 52.4mm?

Which Mikuni ??