What about the expansion gaps of 5mm that is meant to be there between each tile?

Poor demonstration

hi mate great job n which code you recomend ??

Greetings from 1600's! 😂😂😂 from a german!

used these on our 14 degree roof, no problems but we now wish to fit a velux, any tips on how to remove the slates as there have , as designed, bonded to each other?

Used these on our 14 degree roof, excellent but we now wish to fit a velux but unsure how to remove the slates as they have bonded together. As they are designed to do.

why have you not detailed the critical step of how much space you need between the sheets so we know how to space the rafters? Surely that would have been an obvious thing to cover in the video? If using 700mm wide sheets then how far do the rather need to be spaced apart? 725mm maybe ? I need to know this before installing the rafters?

What do you donif the width of the roof is such that the other end of the roof, that you dont shiw being fitted, is not perfectly in line with the corrugations? You've shown all the ways bits but very kittle about the other end of the roof.

Useless video 😂

Can this use for kitchen exhaust smoke?

'BLM'

You say that but to finish a rub I needed 1600 so had to do it really for cover flashing

You nailed the rig in the wrong place

What does sinfettic mean?

Should the galvanized nails pop through the OSB by approx 5mm ? They are now condensating and dripping water.

Despite what it says DO NOT continuously overlap the sheets. You will get eaves creep so that after 4 sheets your eaves line will be about 30mm lower than the first sheet. I suggest you overlap and then underlap and repeat - that way you can maintain a straight eaves. If you decide to put them on battens / "purlins" you will need to think about how the tiles will lay on the barge board pieces. I had to notch the ends of my supports.

Can you tell me what make/type of solar brackets these are please?

You loose the head lap of the tile with your lead slate as shown in your video lol. Not good advertising 😕lol

With the flashing tape, did you just peel the top half off first and stick that? it looks really tricky.

Look very impressive. My only worry is if one was to need replacing it would be very difficult. Any addresses in Birmingham UK that have these tiles.

What is the quality like... I've read some bad reviews on this stuff

Great video. Thanks for sharing .

Can you walk or kneel on the sheets when fitting?

Fucking nonsense

Cut mine with a circular saw with fine teeth. Much faster.

Great do you do an option for wood burning twin wall flies pls

Is there a greater chance of water ingress using this step flashing technique over a lapped square step? I have just had this done and am getting water ingress.

Why so many battens? Put the lead slate under the side tiles and the top check isn't going to do anything except kick the next row of tiles up.

What should be the spacing of rafters

I wouldn't put these on a bird house roof never mind a conservatory roof

Use 12.7 mm or 1/2" wood drill bit to drill holes for the super fixing buttons. How the hell can I get 12.7mm drill bit? In the civilised world people use mm not inches. Easier to get a moon stone than 12.7" drill bit...

What’s the tool called with the slit in it, for bending?

Surely the ridge covers lap so the middle is the top section? Basically weather proofing

hi mate how to paint the rubber flashing

Seems like the perfect cheap solution for smaller builds like sheds. But can it be used for a proper house? How long do they last?

Can these be put over existing asphalt shingles?

Can these be put over existing

So how do you cut it if its hanging too far over the edge eg on dormer?

That only worked cos the bricks was sponge and the axe was blunt

Hi, great vid......thanks. I'll be going through this process soon for a house extension. Please could you let me know the life expectancy of the rubber boot, and how waterproof the whole thing tends to be ?? And is there a better way to ensure 100% waterproofness ?? Many thanks 🙂

We want to use this product for the roof of a large single slope timber outdoor room. Is there an option available for finishing the top edge of the sloping roof?

Can you walk on it to fit the ridge?

Great guide owwwww yes

using these just now on our extension - 15° pitch! easy to fit, from more than 20' you would swear they were real slate!

They look a bit soft,don't they blow up in high winds?

good video but how do i fix it onto my roof ive got concrete beams?.. thanks