Thanks! Well done!

Не перестаю восхищаться , золотые руки , богатая фантазия а ещё и чувство красоты на третьем издели , ну а мотоцикл это настоящая ювелирка ! Молодец братан я с тобой !😊

thôi bỏ ra ít tiền mua con máy cuc về chạy cho nhanh

They used bread also in a few videos.

Super

Very Good ""!

Very creative friend, you're an Artist!! Love it!! 👍👍❤

Золотые руки дают о себе знать ! ( Брат , я с тобой ) 😊

Здравствуйте, поздравляю, хорошая идея, я думаю сделать то же самое, можете ли вы дать мне размеры, у меня есть пружина грузовика, я разобью ее с ее помощью...

Nice job. Welder fabricator for 17 years. Similar to the tool I made to press my universal joints out a few years ago.

You can use bread stuffed in the hole too.

There is an easier way than this video. almost everybody who has a shop , has the tool as well. It' a welder!You weld the bearing race around the inside, and when it cools it shrinks and falls right out. Unless you have done a bunch of final drives on heavy equipment, you probably will never need this.

Świetny pomysł! Pozdrawiam!

درود آفرین لذت بردم❤❤❤❤

Enak kalau punya banyak peralatan kerja.... Kadang" Idea sef Gudang . Tapi ga punya alat nya

Where the heck should i get a huge bearings

Hi,hello,sir,good,job,sir,your,talented,have,a nice,day,🙏👋👍

Good

It's actually not that Innovative it's probably at least 50 years old, it's called a Nutcracker, Nut Buster, But Splitter etc. Definitely has its uses, we used it in volatile environments where Sparks are Flame would cause a real problem

Instead of grease i use Toast bread😅

Very clever. Now I need to make me a new tool 😊

🤩🌷🌼🏵

متریال خوب . جوشکاری عالی. ابزار کاربردی😊❤

Quite a mammoth task. I don't quite understand not having Gib strips in the dovetail slides

Good ."!

You can do the same thing with bread instead of grease.

Excellent, Great video!

A slice of bread works pretty good and cleans up really easy

This method works well on spigot bearings. But I use bread instead of grease works better & less mess.

For the case when only outer body of a bearing left, I'd do the same steps as the author had done before started drilling. Then, I'd weld a "hook"(anything to grab) slightly off center in the middle of the rod length. Stick that into the bearing and by pulling straight you'll also force the rod to grab on the bearing body by twisting the rod. I guess, that's one of the simplest and most popular diy bearing removers.

@1:50 just run a bead of weld round the inside. It will shrink and fall out every time

Well done mate.

I love the last one. That's exactly what I need. Wish I could buy it.

The first thing you do is 1. Next up, if I ask you, can you write down the measurements, I am thinking of doing the same...

@2:20 What sorcery is this?? Just casually 'booped' the metal with your marker dead center, no big deal

GREAT JOB. I BUILT MY OWN BACK HOE 25 YEARS AGO. COMES IN HANDY. IT'S ONE "HOE" I CAN BE PROUND OF.

Навіщо придумувати велосипед? Відкрий для себе набір зємників.

Thanks! Great idea!

Excellent!! Great job!!

May I ask what your day job is? Are you a machinist (like I am!)? You have the mind of a talented machinist and you have some nice machinery in your shop and I enjoy watching all the hacks that you come up with to make a job just that much easier 👍🏻

الفكرة جيدة في الأول لكن استخراجها صعب جدا حاول ان تجعلها اكثر سهولة

I do like my took steel pulling over the rebar but not to picky to make one if need be

drill a hole at the end of the long lengthwise cut so it doesn't start cracking.

Болгаркой делаю железо круглое режу сверлю нарезаю железо упругое! Мужчина должен сделать такое однажды , я не буду повторять дважды

Estúpido lo hizo muy corto

You sure are bloody smart, love the machine

Sweet tool.

Aspacial work zabardast well done

I've seen this done with a piece of bread

What's the ratio for same speed