shrikrishi

Пікірлер

@ashishsardar1492 Жыл бұрын

Sir thank you this video is very very helpful to understand the all concepts

@shrikrishi Жыл бұрын

🙂

@shubhampreet9928 Жыл бұрын

Not clear i don't know why everyone is commenting that it is very nice explanation

@suradhanumjayasubrahmanyam8584 Жыл бұрын

Enjoyed the video in a nice understandable way . Thank you dear brother for this.

@samarsekharreddy Жыл бұрын

Very good

@mdmojahid7598 2 жыл бұрын

Thanks for sharing

@johnchristianmelano8515 2 жыл бұрын

very straight and clear explanations. big thanks.

@Srk7028 2 жыл бұрын

Good video.please give the link for tolerance zone chart..

@ravikandgule5556 2 жыл бұрын

One of the best explanation!!... Thank you for sharing!!...

@akosrupp232 2 жыл бұрын

Good video

@sundarramanj1608 2 жыл бұрын

Really good explanation, very very thanks.....

@putulvlogs7142 2 жыл бұрын

Nice video

@Joker-sw4qd 2 жыл бұрын

Thanks broo !! Helped a lot 👍 It'll be very helpful if you share the link for charts in description :)

@bhushanadsul4162 3 жыл бұрын

Thank you

@MarwanMahdy 3 жыл бұрын

my professor took 2 lectures and still couldn't explain this to us. great job!!

@renukamukappa2008 3 жыл бұрын

We need more videos on this topic bro

@renukamukappa2008 3 жыл бұрын

Super bro 💪

@renukamukappa2008 3 жыл бұрын

Please more videos

@renukamukappa2008 3 жыл бұрын

Super

@shrikrishi 3 жыл бұрын

Thank you

@gokcekandemir3391 3 жыл бұрын

thank you this really helped me

@miniosis1457 3 жыл бұрын

thanks its is verry very helpfull for me

@shashiyadav837 3 жыл бұрын

Never understood this concept in my engineering studies. Thankyou

@mohnuzair5442 3 жыл бұрын

Thank you 💘 from srilanka

@princepadayi7729 3 жыл бұрын

Super explanation good explanation

@swaroopsinhbore3564 3 жыл бұрын

best video till now on shaft and hole base system.

@agankachu09 3 жыл бұрын

In a fit such as H7/h6, what would happen if the hole comes in MMC (smallest) and the Shaft/Pin comes in at MMC (biggest) as well. Is there an unspoken rule in the workshop such as a Shaft/Pin should never be made at MMC. Always remove another...0.002 - 0.003? And what are the possibilities that a Hole will come in at MMC (at lower limit).

@pratikpatil9806 4 жыл бұрын

Sahi hain. Seedhe baat no bakwas.

@uss969 4 жыл бұрын

Awesome video sir All topic concept clear There is no confusion 👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍

@differencesinelectricalwor321 4 жыл бұрын

Kamal ka video janab

@shrikrishi 4 жыл бұрын

Thank you ji

@karimreza8433 4 жыл бұрын

Hi good video 😊 Can I get that's table copy ?

@murugesank2233 4 жыл бұрын

superb explanation bro. pls post more videos like this for mechanical

@rezamajidi1219 4 жыл бұрын

tanx

@pranavindi7152 4 жыл бұрын

thanks well done

@saurabhroy7100 4 жыл бұрын

when I can control straightness/flatness by angularity, perpendicularity and parallelism then why will I use form tolerance unnecessary? will not it cost more and will not control perfectly all the aspec?

@shrikrishi 4 жыл бұрын

Straightness and flatness are independent features so whatever torrence given within that you will get, and what you suggested in that case it is dependent so won't be that much precise than individual feature control. Hence you will use individual feature control only if that much precession is necessary so then cost will be obligation for your requirement.

@saurabhroy7100 4 жыл бұрын

@@shrikrishi how can you say won't be much presice when angularity, perpendicularity and parallelism control both flatness/straightness + orientation then tell me which one is more precise.....form tolerance or orientation tolerance?and tell me the logic too...only telling something doesn't state anything right.

@tebellolesitha7643 4 жыл бұрын

bruh you are the best!

@pradeepdhapade965 4 жыл бұрын

@NatureGod369 4 жыл бұрын

Hey Srikrishi, ur videos were better than made by foreigners , why did u stop making..anyway, whatever u made, all videos have excellent animation and u cleared all the doubts which I used to get. Take care. God bless u.