Do you also have to cover/fill the screw hole with anything? Or is the screw alone enough?

Im installing 18 foot horizontal 26 guage any tips on oil canning?

I would have liked to see a REAL demo instead of listening to a lot of chatter. I am experienced with metal installation including ridge caps and vented ridge caps. Your product looks good but you could have done much better for the benefit of the inexperienced installer.

Will this stop wind driven rain from coming up and into the roof ridge?

Why show a thumbnail of zxl dome screw...yet give demo with standard type?? I was excited to see a dome head demo.☹️

i would add an extension to the drill so that the clutch on the drill doesn't scar the snow guard - and it saves your back so you dont bend over as far when you install them.

Do they make a post installation product or recommendations for a pest block AND breathable solution? I don’t want to have to deal with a dissasembly nightmare to install this product. TIA

Whats the brand name of those closer strips? Those are great.

Do they make a strip that keeps dust out When they put my metal roof on they did not put that stip in and now I have dust getting in my house every time a car goes past my house on the grave road inlive on

Say that I over screwed it. Can I really go back, replace the screw with another one, and screw in the same hole with the new screw?

Why say " whats up guys? if you have no intent to give us to actualy answer it?

The firs thing you could do is learn how to hold your camera horizontal it is not that hard.vertical is pathetic.

How do you work / access the roof when the pitch is great than 8/12

Might try a split bar Angled to send the snow off to each side of the door .. ? Might work .. but adhesive only is good advice

My roof let's the snow slide off really good lol skips right over the gutter .. But the snow pumbled my bushes and the front step.. so I need a balance protect the entrance And to heck with the bushes

Good info.. Sounds good.. glue only if not installing the entire run end to end .. I'm tempted to install just a few .. I like the weight of the snow off my roof so i don't want to hold it all back..

Hi I have a double wide 30 year old manufactured home. No attic. I’m replacing all the screws on my 20 year (?) steel roof. When at the ridge I noticed some of the foam was pushed in and missing. Is it important to have those vent strips without an attic? If so Thinking of removing entire ridge and putting in your product. Thanks!

Price?

Is 1x4 okay spaced same as cedar shake? Or full plywood

I see these have a grove on the tip of the screw, are they also self tapping screws? (FIY, It would have been a nice touch to have shown that they also self drill through metal, if they do that, that is)

Hi do you guys have available for R panel sheet metal?

Is underlayment not necessary for this roofing system? what about battens?

Looking at: peel and stick then a radiant barrier with 24g Galvalume installed on 1x4 battens using metal clips. Should I spend the extra $ for a painted metal or will "naked" Galvalume give me the performance I'm looking for? TYIA

When you created this video I am doubtful you thought about people like me commenting two years later. Excellent video.

How do I get a contractor to give pricing?

Hello, I was on your website and was wondering if you prefer this vent over the rolled Profile Ridge Vent or vise versa? I have the classic rib with a 9" spacing 3/4 tall so I could do either product, just want the best long term option?

I have to wonder if there is a NFA rating on these. It looks very restrictive, add in some dust and debris.

Do the screws go through the strip?

if the ridge vent strip has gaps in it are insects still able to go thru ?

CTE Coefficient of Thermal Expansion

Shared blog post link is jot available, can you update the link?

If you don't mind the extra hassle, is there any reason not to put a dab of silicone or some other caulk on each screw before you install it? It seems like this could greatly extend the life of the screws.

I’ve purchased this system and have been trying to figure out how to cut the hip cap at the trim. Also where the hips meet the ridge. Are there any pictures of this?

Did they ever answer the topic? I gave up after the 5 minute mark.

I didn’t give it 2 thoughts when I built an addition on my house and added a tin roof. However, I cannot talk on my cell phone in that room. It may not cease and desist the signal but it definitely interrupts it and makes it so that a cell phone conversation cannot be had. That’s just my experience and it’s been going on for the last 15 years since I built it. When I walk out of the room, I have perfect reception. 🤷🏻‍♂️

I’d like to know how to add a bathroom vent cap. Or I should use pvc pipe for venting?

What is the density of galvalume?

nice video.. how to replace the closure strips once they have worn out on a 20 yr metal roof do we take the cap off to replace them or cut and paste

How long you think that rubber grommet will last?

Installed metal snap lock roof panrls have minor oil canning on roof. My concer is on the gable end the last panel is screwed every 12" along the edge with the z trim to support the gable trim witch is creating major oil canning what did I do wrong?

If you have a 4"x10" ridge beam bordered by plywood, how does the hot air exit the attic? Do you cut strips out of the plywood next to the beam?

I think i need to remove my ridge cap and get some of that closure strip. Whatever they used years ago has come out in spots and seeds from my oak tree keep ending up inside my attic.

I just got galvalume intalled in my residence... and notice that the back of the panels have to two different colors and texture; so, I would like to have a lab to do the testing if I am getting the same material "galvalume" I contracted for. I would appreciate your help getting a lab regarding this matter....

How do I clean my good, older galvalume acrylic? coated roof? What kind of galvalume roof do I have? Can I send pictures?

Thanks guys for informing us I am getting ready to install or have installed a standing soon roof and everything you spoke about is my concern

I was trying to figure out a point to make on a storage related topic. The best advice i can give from warehouse perspective would be proper placement of staging boards. Example if I have 3 packs of panels the heavier pack/longer pack should be on bottom. If forced to use the ground i look for 3×4 wood placed roughly every 5-6' apart.its very important if stacking on top that pack to align the boards for that pack directly in line with the ones under to avoid warping.

if you have shingles and plywood and are converting to metal.. then when you cut or over an existing ridge vent you can put 1/4" hardware cloth / screen and its big enough to provide good flow without getting clogged by dust and won't let in bats which are the real problem.. bats can get through a 1/2" gap or as big as your thumb.. obviously bees can get in smaller openings but they are easier to kill with a spray than bats with a shotgun in your attic.. not gonna be pretty heh... just a word of cheap prevention advise. if anyone does know of a spray that kills bats please pass that on heh... considering a commercial bottle of spray foam insulation and spray gun to get um

How do you think the color MS brown would do in full sunlight 24 hours a day for the next 40 years? I have a cedar house so it would look great on top of my roof.

What is the best paint over old/new galvalume and mixed color painted panels

This roofing system looks amazing!!!!! Such good information. It makes me want to run out and put one on my house!!!!