Thank you.

During pumping oil that time , we have to stop the compressor or not

But let suppose if we need to change this Module what is the procedure need to do blackout to replace this module or how to do that please explain.

Thank ypu for your shared videos its a big help for new aspirant god bless sir

I am from India sir Your videos are very helpful sir keep sharing your knowledge

You should be use vacuum pump in compressor

Thank you so much for this instructive video. Please keep sharing troubleshooting videos. 👍

Hey my friend, how you doing? I would like to know if you have any information about disassembling the Damcos LPUM-s, the manual doesn't help much... I have enought spare part on board to do so. Seal kit, hand pump kit, seal kit for actuator and so one and so forth.. If you could help me would be very grateful

Over Limit

Sana demo mu ng actual paano mg blow off ng level transmitter

good afternoon, please tell me. Do you provide support with the commissioning of such a system?

Hi sir I have problem about ac system . When ı start the 4th stage lp be coming until 3,8 and hp 18 evap side has startıng ıce also 3rd stage not enought for cooling fan flap position %30 open from atmosphere and evap good condıtıon air flow is good out sıde temp 35. When compressor stop posıtıon condenser liquıt level is full but when ı start comp glass showing emty lıquıt. So ıce problem is less gas or not

tnx

LamBda controler..not Lamda Mr.Barko

Hey bro. We look for your new troubleshooting videos. Keep sharing it 👍

Good day...please advise if air charging valve is closed during normal operations

Good day po thsnk you for sharing this beautiful content with us God bless

Which was problem? Why coming alarm? If leval transmitter in good condition)

Lods anung M/E type maker ito..

hello sir, ask ko lang bakit ataw mag fire ng boiler sa emergency mode?sinunod ko naman ang procedure. may ignition naman sya ok naman ang oil pressure kaso ayaw mag fire hndi umiilaw yung flame scanner indicator..salamat po.

Thanks a lot ! Do I understand correctly that the mechanical overspeed is located at the end of the camshaft?

thank you sir for sharing your knowledge and experience, God bless always sir🙏🏻

Thank you sir

Lecky nominal voltage nyo 450 o 440 gamit...

Thank you Mr. Barko. You have made really good learning resource for all seafarers around the world. 🫡

Thanks a lot ! What air pressure is supplied to the compressor wheel of a Turbocharger?

Thanks a lot ! What air pressure is supplied to the compressor wheel of a Turbocharger?

Sir if wire covering is gone can I use sleeve with 125 degree Celsius tolerance

Sirr ,you can make prosedure pump down this type air cond please ,and I want to ask, in this type air cond. if i want replace filter dryer,does it need to be pump down?

Thank you for the vídeo, please continue to explain in english, helps a lot !

Thank you

Thank you. I am 3rd engineer in Korea. Your video is very informative. I look forward to seeing good videos in the future.

excellent

Is it possible, sir, to explain to me more about how to set the thermostat to the negative position below zero and then return to the positive position again? Thank you.

Can you please share me Lamda part explanation

Ayos Idol ah

very informative video,,

❤

🎉🎉🎉good

Me No understand Sir 😂

very helpful, thank you

Good

Good

Hindi na na seset ng tama yan sir na sobra ako sa clear 52k plang odo lo masa 80plus na next pms

sir tanung lng pó, d po ba masira yung diode habang nag Megger testing alternator?, bagúhàn po ako

Can you guide me where to use the over speed application?

NASA impa bato sir pressure calibrator pano mag order

Good day sir..ano po problema ng main engine bakit pinalitan ng angle encoder?sa amin po nagka problema main engine namin pag e.timing sa 210.7 which No. 4 is in top postion if we move dead slow ahead main engine will not start but in astern main engine will start..is this angke encoder is a problem?salamat po sir

Good music 😂

Nice one eto ❤