Lake Erie Arms

Пікірлер

@CaptainNola 3 күн бұрын

How much did the custom work cost?

@Woodytomahawk 6 күн бұрын

Also the direction of the ejection 3 to 4 o'clock properly gassed system

@urgirlswantme2 7 күн бұрын

cause it was cold on the range or could be the round just being shy

@randymarlow8864 12 күн бұрын

Got my Howa .300 short mag 1996 great shooting gun

@mastershredder8738 29 күн бұрын

Awsome

@originalowner1037 Ай бұрын

Its from the factory. I have a Rem 700 PSS DM (Detachable Magazine).

@jordans.1910 Ай бұрын

Does your range have caliber restrictions?

@joeybonfante5580 Ай бұрын

What barrel is on this?

@henrygonzalez360 Ай бұрын

It definitely looks amazing 👍🏽🎯

@andreaskoudellou3256 Ай бұрын

If you want to paint the wood stock you have to sand it down and spray primer on it

@misterlewgee8874 Ай бұрын

Over cocking? Interesting.. I wonder what the "machining process" was ...

@edwardcarter-vd2hw Ай бұрын

I wish there was a reaction video for the moment the owners gun had full assist 😂 if that is even what happened

@marcschneider793 Ай бұрын

I have the same rifle. May I ask what you guys get for barrel threading and doing the stock in camo ?

@perry19631 Ай бұрын

I'm not sure what you mean but all my Remington 700 are cock on open, not cock on closing.

@emanuelpowell1526 Ай бұрын

What Chassis is that? Stock Remington?

@usmc2044 Ай бұрын

That DBM is factory on the mountain rifles they made in early 2000’s, not sure if they still offer that rifle or not.

@adriangoot1042 2 ай бұрын

Ammo problem, not magazine problem

@Splashbros-hu5fk 2 ай бұрын

Why do people like scars they are over priced and can’t take p mags

@braylonwoods-p7f 2 ай бұрын

😂😂😂

@fisherthegoat 2 ай бұрын

The aesthetic mostly, but they are genuinely good guns, at least in the case of the SCAR-17. Idk much about the 16.

@moscasucio1686 Ай бұрын

Folding stock, lighter recoil

@Splashbros-hu5fk Ай бұрын

They overpriced for how sh## they are

@fisherthegoat Ай бұрын

@@Splashbros-hu5fk have you shot one

@Okgam3r 2 ай бұрын

This happened to my galil when i attempted to load a round once, brand new gun, could it be it just needs to be ran and itll work itself out

@ARob0570 2 ай бұрын

Failure to seat?

@brattman741 2 ай бұрын

Couldn't it have just been a bad crimp on that one round?

@nategaudette4228 2 ай бұрын

could've been a poorly sized piece of brass, but you dont really need a crimp, if the brass is sized well the neck tension should hold the bullet. But yea, id say it could have definitely been a specific round defect.

@Patrick.Henry1776 2 ай бұрын

@@nategaudette4228 bro, the die provides the neck tension when the bullet is seated. Neck tension and crimp are basically the same thing. The neck tension isn't on the case before seating the bullet.

@Patrick.Henry1776 2 ай бұрын

@brattman741 ... Yes

@nategaudette4228 2 ай бұрын

@@Patrick.Henry1776 no that isnt true. a crimp, and neck tension are completely different, and completely different dies, and processes. You set neck tension while sizing the casing, you crimp after seating the bullet.

@Patrick.Henry1776 2 ай бұрын

@@nategaudette4228 neck tension is set when the bullet is seated not on the sizing die. How can you set neck tension before you push the bullet into the case? I know neck tension and crimping are different. I didn't say they were the same. They just perform similar functions. Crimping is done on a case where the bullet has a cannelure. Neck tension is done on a straight sided bullet.

@dkn2128 2 ай бұрын

He rode it closed

@johnrelford7961 2 ай бұрын

Extremely slow hand cycle caused this you always have to to it quickly if you do it slowly on an FN 5.7 it's gets stuck

@braylonwoods-p7f 2 ай бұрын

It’s not a five seven though?

@MartinKirk-y5v 2 ай бұрын

Martin John Gonzalez Jennifer Wilson Amy

@lizzapaolia959 2 ай бұрын

What a joke 🤣

@Golden_Ace 3 ай бұрын

I hate that plastic packaging too.

@jayprevett6657 3 ай бұрын

I would trade my tikka t3x for that without hesitation

@HazardousRob 2 ай бұрын

You'd be foolish.

@jayprevett6657 2 ай бұрын

@@HazardousRob yeh i know but it looks so cool!

@timothytucker3652 3 ай бұрын

If that is a true AR-15 why not contact Armalite,since AR is short for Armalite

@AlkyCheeks 3 ай бұрын

Whatever point your trying to make is stupid

@jordans.1910 Ай бұрын

Damn you are dumb dude lol

@ram218313 3 ай бұрын

sound like rings or gas key is the issue

@brettlyde9220 3 ай бұрын

Rings are a wear item replace them

@richardsveum8452 3 ай бұрын

Unusual for a BCM to have issues, Contact them, I'm sure they will replace it.

@Colorado4x4 3 ай бұрын

Guys, answer the questions from the people that comment. It helps your audience out and they will understand turn subscribe

@georgew657 3 ай бұрын

One thing everyone is missing is the mag.

@zack9912000 3 ай бұрын

Check the tolerance of the parts. The affordable ARs are almost never correct. Also, it sounds like the gas block was not pinned as it should be. People get what they pay for

@HarrisonFord11 3 ай бұрын

Misaligned gas block and too heavy of a buffer.

@GunBoss1776 3 ай бұрын

Drill out the gas port SLIGHTLY and itll work fine. Go through routine maintenance first and if it has an adjustable gas block, put it on the next setting to allow more gas. After all that is checked, drill it out. just a little will do. It doesn't look like its had 3000+ rounds so i personally dont think its gas rings but its an easy check to see if they are good by turning the bcg upside down to see if it holds its own weight up.

@kilpeoplebreaksht 3 ай бұрын

It was immediately apparent it's either under gassed or misaligned gassblock (causing a under gassed issue) maybe maaaaaybe buffer weight or spring since it's a "pistol"

@AidenBraydenPodcast 3 ай бұрын

Where is the rest?

@TimmysHR 3 ай бұрын

First thing I’m doing is trying a new mag

@mckenziegent1423 3 ай бұрын

Omfg y’all better hope shit never HTF what y’all gone stop and put your ear pro and your eye pro on before you engage a threat😂😂

@mckenziegent1423 3 ай бұрын

Pussies I swear like y’all act like a gun is just gonna magically shot somebody

@adriangoot1042 3 ай бұрын

Loose gas key

@GoatPilot04 3 ай бұрын

You forgot to mount the scope the right way like the NAVY, thats whats wrong! 😂 You know, backwards!

@jason87k 3 ай бұрын

Lmao they relieved that guy from command

@GoatPilot04 3 ай бұрын

@jason87k The heckling amongst his peers....ruthless.

@cwhitty05 3 ай бұрын

Had the same issue. Mine was the gas block that lost its alignment with the gas port. PSA upper, 8.5” 300BLK, pistol length gas system.

@DeadlyBreath9790 3 ай бұрын

PSA has terrible QC in terms of actual putting together of the upper, they should warranty it but seems like an easy fix, not worth shipping it back to them.

@cwhitty05 3 ай бұрын

@@DeadlyBreath9790 I just fixed it myself. Like you said, not worth it. If it were a broken part that’s more than $20, most definitely would’ve sent it back.

@HH-zi5ih 3 ай бұрын

Of the thousands of m4 style rifles I’ve had to repair, I may have run into an actual issue with gas rings once. It’s almost never the rings, unless you buy one of those gimmicky one piece setups that everyone thinks is better. Its not. With a normal set up, one ring can even break completely (I demo that by firing with only two work out rings) and the other two will get the job done. I’ve demonstrated this in teaching other people how to diagnose and fix gas issues.

@richardsveum8452 3 ай бұрын

My Department bought Windham AR15's, I know, I know. All of the rings in 7 rifles had to be replaced within 2,000 rounds

@HH-zi5ih 3 ай бұрын

@@richardsveum8452 that’s insane! Not surprising if you got a whole batch of bolt carriers out of spec from windham rifles, but extra space from out of spec carriers is the only way you’d have that many failures from rings. I’ve done it a long time and never seen that many.

@richardsveum8452 3 ай бұрын

@@HH-zi5ih They were all consecutive SN's so I would imagine a bad batch

@SouthBendShovelSlayerr 3 ай бұрын

When I bought my first AR last year after I took it home I stripped it down to clean it and lube it and noticed the gas rings on the BCG notches were all together. I was told they need to be spaced out. Is this correct?

@michaelsorenson3887 3 ай бұрын

The gas rings will function just fine with the gaps lined up. No need to worry about that. Its a myth a lot of people get hung up on. Ive never had an issue from the gaps being lined up.

@supernautj1s 3 ай бұрын

If you apply the same logic that you would to cylinder rings on a piston... Yes you should stagger them! Better seal and less wear. Ask yourself, "would Eugene Stoner stagger the gaps on the gas rings on the rifle he was engineering?" FUQ YES HE WOULD!!!!!!!!

@slimthugger5794 3 ай бұрын

It’s the aftermarket gas block tighten it

@Mrwhatarethose 3 ай бұрын

Check the magazine?

@coreyweiss6210 3 ай бұрын

Means try a different mag to see if the feeding issue was from a faulty magazine

@scrotalrecall9653 3 ай бұрын

Average ar enjoyer trying to fix his ar’s gassing issue biannually

@janderson3918 3 ай бұрын

Most likely buffer weight or spring

Ең жақсы KZbin

Пікірлер