Can the polished aluminum bezel be changed on the supreme series?
@prosportgaugesАй бұрын
No, but we offer a black bezel trim cover.
@bangsta92624 ай бұрын
Howdy. How can i do it without that button on the display? I got the 4in1 Gauge. Greets from Switzerland
@timlynd73304 ай бұрын
We do not sell that gauge here in the states. You will need to reach out to the store you purchased it from for support on that gauge.
@bangsta92624 ай бұрын
@@timlynd7330 aight thank you. Already sent a Email. Have a good one
@rebeccasawyer90105 ай бұрын
Could you advise me how to do this with the Water temperature gauge please ?
@timlynd73305 ай бұрын
Same for all. Red wire must be on constant 12v to retain memory.
@rebeccasawyer90105 ай бұрын
Many thanks @@timlynd7330
@kristianhermann59716 ай бұрын
Incredibly quiet and fast gauge - makes my GlowShift look and sound ancient - do all your gauges use the same silent/fast stepper motors?
@prosportgauges6 ай бұрын
For now, Supreme, Crystal Blue, and JDM series have this very fast and silent stepper motor.
@al3xsad8 ай бұрын
Hi, does this AFR gauge require a controller ? Can I connect it directly to a LSU 4.2 wideband ? Thanks !
@prosportgauges8 ай бұрын
This is a fuel pressure gauge. Wideband AFR gauges require the control box. Narrowband gauges do not, they will wire directly to your stock o2 sensor. Our wideband kits include and only use LSU 4.9
@al3xsad8 ай бұрын
@@prosportgaugesdamn, I wasn’t paying attention that this is a Fuel gauge, not an Air/Fuel Ratio one as mine is, unfortunatelly I don’t have a controller for mine and now that you mentioned I’m thinking what type of gauge do I have, wide or narrow band, is there any way I can figure it out ? Thanks again !
@prosportgauges8 ай бұрын
@@al3xsad Send a photo of the back of the gauge to [email protected] and we will let you know!
@thomaswahahauw560 Жыл бұрын
😂 crossee my path I had it in my mind to search for it..later anyways have a blessed day !!
@worldrallychef9644 Жыл бұрын
I feel like it’s strange you can’t do this with the buttons..would be MUCH easier
@darksideshero2319 Жыл бұрын
That would be great if that were an option as well as the option to adjust brightness.
@prosportgauges Жыл бұрын
@darksideshero2319 @worldrallychef9644 Both options available on the premium version if this gauge "216EVOAFRPK4.9-WO"
@darksideshero2319 Жыл бұрын
Wouldn't mind knowing the LED part #. Blue color has lost its brightness so much the gauge the gauge doesn't look like it's turned on. I've switched it to red which helps a little bit I would like Blue. I've attempted adjusting the brightness as well but that didn't help, it's on max.
@prosportgauges Жыл бұрын
The LED lights inside are not serviceable. They are surface mounted tiny ones, about the size of a pinhead.
@darksideshero2319 Жыл бұрын
@@prosportgaugesI work in SMT and would be able to service them myself with the rework station. Thanks anyway...
@prosportgauges Жыл бұрын
They are not serviceable, no part number is available.
@PepegaPig Жыл бұрын
Hi Can you help I am able to turn off the regular alarm by this method but I always have the start up beep...which was disabled until I changed battery Please help!
@prosportgauges Жыл бұрын
Sounds like the dead battery made the gauge loose your settings. Try the process again. Be sure you have red wire to a constant power source to retain memory.
When installing them be sure the red wire is on a constant power source to remember your settings
@admarshall4 Жыл бұрын
Does this just silence the start up? Or silence the warning too?
@prosportgauges Жыл бұрын
Both, this removes the "beeping" sound from startup and during the warning. The gauge willl still flash deep red when you go into warning mode.
@nielschristensen8105 Жыл бұрын
How do you silence the gears? It sounds like there's no grease on them
@timlynd7330 Жыл бұрын
Silent gears are in higher end models. Crystal blue series, Supreme series, and JDM series are all upgraded fast and silent motors.
@MJT-DA2 жыл бұрын
What size is the oil adapter plate?
@prosportgauges Жыл бұрын
We offer them in 4 different thread sizes to fit most vehicle. email us directly with year/make/model/engine liter size for the exact one for your vehicle.
@MJT-DA Жыл бұрын
@@prosportgauges2014 Hyundai genesis coupe 2.0T 4 cylinder turbo. (I didn’t see your email in the video desc)
@elemix272 жыл бұрын
Wish I would’ve known this before I used pliers and accidentally ripped it off 😂
@xZKrYpTiK2 жыл бұрын
do these have the same blue lense as the performance series
@prosportgauges2 жыл бұрын
No, these have clear lenses. Check them out at www.prosportgauges.com
@xZKrYpTiK2 жыл бұрын
@@prosportgauges maybe the next guages i buy i will go with supreme series instead of the performance ones i have now. i love prosport gauges ive been using them for years.
@Eli07K2 жыл бұрын
After only one year this gauges all 4 of them that I owe don't glow white anymore. The white has faded and the red has taken over. Can they be open and that white light be replaced?
@davidvue92662 жыл бұрын
How do you make the gauges stay on that color?
@AblationMusic3 жыл бұрын
Hmmm I don’t think that oil pressure gauge is accurate at all. It was hitting almost 70psi at 2300rpm? No way in hell that is accurate.
@orabates18233 жыл бұрын
What he Probably has is called tinned copper wire."TInned copper wire is copper wire coated by a base alloy such as solder better known as tin. ... Primarily, it strengthens the copper's natural properties,"
@boosted00793 жыл бұрын
I noticed the core wire you have didn't look like copper wire. Does that matter really? The wiring on my engine harness looks like the wiring you have there. I got a spool of 16 gauge wire from the parts store, but it's core is copper. Just wondering if that's going to have any negative affects on what I'm doing? Extending the ignition control section of the harness to relocate the ICM.
@prasadavagadda59623 жыл бұрын
How to order?
@stevendanielscobbie3 жыл бұрын
HAs anyone come across a code [5] constant on the EVO Wideband AFR?
@FCJBCN4 жыл бұрын
Hello could you help me. I have installed these gauges and they reset when I turn off the car. I have seen that you have commented that I install the red wire to a 12 v power source with current with the car turned off but then the gauges stay on when I turn off the car. I am desperate and I do not know what to do with this problem since it is very annoying to configure everything every time I start the car
@prosportgauges4 жыл бұрын
Looks Awesome thanks for posting the video
@yungkhajiit4 жыл бұрын
The screws in the non used ports, are they all the way screwed in?
@BowsettesFury6 жыл бұрын
I sent your company an email early this morning but I don’t think the person who answered me fully understood what I’m trying to do. These gauges are beautiful. I have an 05 Neon srt4 and want to put your fuel level, speed, tach, and engine temp sensors in it. Got a block off panel made for them already. Power and grounds for them isnt an issue. What I want to know is how they receive a signal for the read out, is it possible for me to pull out my factory cluster and use the signals for each of the original gauges to get yours to display the correct numbers??? Is there some kind of trickery that I can do to make them work properly? Really don’t want to pay a truck load of money to Dakota Digital and I like these displays much more. Thanks in advance. 😊
@prosportgauges6 жыл бұрын
You CANNOT use your factory sensors with these gauges no matter how much magic sorcery you use. No matter whose gauges you use you HAVE to use the supplied senders (except for Tachometer) in order to get accurate readings. For the engine temperature you can use our Oil filter adapter plate 3/4"-unf size.
@BowsettesFury6 жыл бұрын
prosportgauges that’s what I was figuring on. Gotta make a bigger hole in my firewall to fit all the new wires through. Thanks that’s all I wanted to know was to make sure that’s what was up. Gonna continue to save up as much as I can and get all the gauges at once. Do you think it would be possible to start at the factory plug, build a new harness, then use your sending units? Never done it that way before, just wondering because of my car being so small and such a pain to work on.
@prosportgauges6 жыл бұрын
It is pretty easy to install the gauges and run the wiring. For the EVO speedo - use our GPS sensor Tacj use the tach signal off your ecu Temp - use the adapter plate Fuel level -you can use factory signal and adjust our gauge to match. Then wire the power/ground for each- it is really not that hard..
@TrinomCZ6 жыл бұрын
What's the name of that song?
@KrissofallTrades7 жыл бұрын
How do u get these to remain blue all the time. Mine reset
@timlynd73307 жыл бұрын
Your red power wire has to be connected to a source that is getting 12v even when the car is off. (memory wire)
@KrissofallTrades7 жыл бұрын
Haha, I figured it out. But I wonder, how much power does the memory consume?
@prosportgauges7 жыл бұрын
Kriss very little. Just like your radio or clock memory.
@KrissofallTrades7 жыл бұрын
prosportgauges ok cool I love these gauges. They are extremely bright. I have had 3 other gauges for about 2 years or 3. Is it normal for the light to dim over time?
@prosportgauges7 жыл бұрын
Kriss It's the technology in the LED's that change over the years. You can adjust your brightness on the new gauges to match the old
8 жыл бұрын
When will the speedo and tach be available?! I've had my eyes on them for some time now! Wanting to totally swap out my Miata's gauge cluster with all of these!
@prosportgauges6 жыл бұрын
They are out now
@MUDERERprofile879 жыл бұрын
I used this today I ordered the premium version but it don't come with sending unit with plug
@Thr33.Sid3z11 жыл бұрын
The 60mm is where its at for these anyway's! These couldn't have come out at better time. I'm almost done with My '99 JDM STi RA build, and was holding out on the Halo's until the last minute, and then these puppies came out!!! Can't wait to install them. Can't wait to drive my car, but also can't wait to see these in action!
@prosportgauges11 жыл бұрын
No, not yet. only 60mm
@vivamagiko11 жыл бұрын
No 52mm option???
@prosportgauges11 жыл бұрын
You can use 16ga. wire to connect to the senders on the Performance series. Premium, Halo & JDM Series come with the wiring harness(gauge to sender).
@nanjwan11 жыл бұрын
Great Video what gauge of wire was used from the sender back into the car?
@Thr33.Sid3z11 жыл бұрын
Thanx for the info, I'm placing my order now!
@prosportgauges11 жыл бұрын
Yes they are brand new. Compared to the Halo series they are faster and quieter. These only have 2 colors while the Halo has three colors. and Halo has Peak recall And warning -While the JDM only has Warning.
@Thr33.Sid3z11 жыл бұрын
So these are brand new? How do they compare to the Halo series? I was going to get the Halo Gauges until I just saw these bad boys
@prosportgauges11 жыл бұрын
Yes, first off the website.
@Mrfoleybmx11 жыл бұрын
Mine was first?!
@prosportgauges11 жыл бұрын
First
@Mrfoleybmx11 жыл бұрын
Just ordered mine !
@prosportgauges11 жыл бұрын
You can also use one of our Oil galley plugs to install either sender. They are less expensive but require more work to install.
@prosportgauges11 жыл бұрын
1 inch
@prosportgauges11 жыл бұрын
They will be released for sale this Friday 6/14/2013
@SpeedHacks11 жыл бұрын
ETA on release of these?
@GradyRho9211 жыл бұрын
how much lower does the adapter cause the oil filter to be
@JasonJacksonWright12 жыл бұрын
Dude good job!!!
@prosportgauges12 жыл бұрын
Call us up for tech support it is much easier/faster. 727-572-9011 M-F 9-5 est.