@@Officialjimibaur at the time I made this video, I was running 8gpm. I now longer run that unit or this surface cleaner.

@@readykleenpowerwashing Thank you, I didn't read the title 😂

@@brianlucas3187 HFS “High Flow Systems” from North Georgia Airless

@@brianlucas3187 the setup in this video I no longer have since it was over 3yrs ago. This link is the current setup I’m running. I also run a bigger surface cleaner in another video. Lil hippo 62” instead of a 49” mondoforce. kzbin.info/www/bejne/kKfUpKeheMmeb6Msi=cNbdIYScf8UG6b7M

Yes

@@brianlucas3187 I’m using a hotbox add on. The machines I’m using are two pressure pro igx800 cold water skid units paired with a hotbox for each machine.

@@blacklabpowerwashllc I’m no longer using the mondo 49”. I sold it the middle of last year and now run a lil hippo 62”. In this video I was only running 8gpm. If you went to run it more efficiently, you definitely need higher gpm to do so but I ran it with 8gpm & 10gpm for over 3yrs.

@@readykleenpowerwashing sounds good. Were you using cold or hot water when using it?

@@blacklabpowerwashllc both. I have videos of it in action if you look at my other videos you’ll find it.

@@readykleenpowerwashing I currently have the mini mondo. I see you’ve used that too. Do you feel the big mondo is better / more efficient for driveway cleanings?

@@blacklabpowerwashllc no it’s not more efficient for driveway cleanings. The mini mondo is as long as you have the proper gpm to run it. The mondo 49” is for big Commerical flatwork.

If the hose burst again…..yep. That’s why it’s called a reusable fitting.

@@readykleenpowerwashing 😆 guess I didn’t read the title well…thanks!

There are three different lines that go on the fuel pump. One line is a (pulse) or vacuum source to operate the pump. In turn the vacuum pulls fuel from the fuel tank as the motor creates vacuum to operate. The last line is the pump output line that takes the fuel and sends it to the carburetor.

I don’t know how I could answer that question and not see your setup.

In this video it was 1” suction hose.

Thanks for the response! (= do you use 1" ID hose for all your 5.5 gpm pumps? I use 1/2 " ID suction hose with 5/8 flexilla. Just trying to maximize output and figure out what the best combination is.

@@mikluvin4633 no. My current 12v system uses 1/2” suction, 1/2” discharge with 350ft of 1/2” flexzilla hose. I get 38ft horizontal distance. If you want better performance from a 5.5gpm 12v system, you’ll need to go 3/4” everything with 5/8” hose for the reel.

No I haven’t. This is for me surface cleaning and that’s it.

Yes. I was just using mine today doing a house wash.

2500

No. because I had 22 of these locations, we agreed in a flat set rate price. Some locations were bigger and some were smaller so it made up for the difference.

@@readykleenpowerwashing Awesome, great info!

Yes I run my 3/8 hose through my reel.

@@readykleenpowerwashing Thanks for reply.

Sorry I figured after 6 min people’s attention span was maxed out. Next time I’ll do that. The main thing I was trying to show was the capabilities of the groundforce with good gpm how quctyiu can get a driveway done.

This driveway was pretty dirty. I pretreated with P40 for a hotter mix. Downstreaming doesn’t get hot enough mix.

@@readykleenpowerwashing why do you pre treat? I see a lot of people wash first than post treat hot mix

@@dylanthornsberry8778 because that’s my preference. Pretreating kills organic growth and loosens everything up to make it quicker to clean. Post treating can be too strong for some customers leaving behind a stronger SH smell. Worst case I may have to spot treat and I’ll do that with a pump sprayer.

2503 x 4

No. If you cut off your water supply and the bleach works then that must mean you have an air leak somewhere. The water line must be sucking air somewhere. If you’re using non collapsible hose like tiger flex hose, make sure to heat the hose before clamping it down. The coils in the hose may prevent a good seal.

Yes

Very happy to hear this great news

Yes you can use the 100 gallon tank and batch mix whatever you want to clean. Since your batch mixing, you’d run the bypass hose back to the tank and you’ll be able to stay off the trigger for a long time without having to worry about overheating the pump.

Thank you for replying, sir. It makes me feel more confident about this matter. By doing so, the bypass will keep the engine running and put the chemicals back into the tank. After every job, do you run clean water through the pump?

@@HandyHoneyBunnyLLC I usually do run water after the job to clear out my hose but in your case you’d have to come up with a dual valve to switch between pulling your batch mix and pulling clean water. Because you’re batch mixing, there is no clean water per se. you only have your batch mix tank to spray from.

Thanks for sharing your wisdom.

No because then you’ll fill your water tank with chemical mix.

@@readykleenpowerwashing aah , i see. Thanks

это маленький бегемотик шепчущий мыть. номер модели h500. стоимость зависит от того, где вы его покупаете. он может варьироваться от 3500 до 5000 долларов.

I got it from Amazon. I stated this in the description.

@@readykleenpowerwashing so the Jobe is your main valve? My Hudson valve busted and not sure what is should use next

The most simple answer to that is as big as you can fit or haul. Everything depends on location and water flow around your area. Also Commerical work if there’s no water access, having a big tank will slow you to do work.

Thank you

Running a hotbox with Wayne burner or SDC burner can run 12gpm.

How does the 48 do with 8gpm? Are you using cold or hot?

@@readykleenpowerwashingyou need to connect multiple unites together to get that 4” per gpm, I run the 48” with 2 8gpm hot water on parking garages

@@bigjjay209 you’re responding to the wrong person.

I use a dedicated pump when I pretreat. Downstreaming isn’t strong enough. I have a 12v system and P40 gas softwash system.

@@readykleenpowerwashing have you tested different injectors? Is it strong enough for regular house washing?

@@batteryboy4529 regardless of what chemical injector someone suggest, they’re still going to perform basically the same based on GPM. Downstreaming does work and effective for house washing of vinyl and hardy plank siding. Brick, stucco or flagstone would require a hotter mix to clean.

@@readykleenpowerwashing understood. I have two 8gpm right now. I just ordered a 10gpm 15 minutes ago. Was nervous that I wouldn’t be able to downstream at all with it. I have an air diaphragm pump so if I need a stronger mix I will just use that. We normally use that already to pretreat really dirt areas, stucco, brick, roofs, etc.

Thank you

One reel is a water reel to fill my tank. I don’t have a water reel that goes to the pump because my machine consumes more water than a regular outlet can put out. The tank feeds the machine instead of a water hose going directly to the pump. I have multiple systems on my trailer and that’s the reason why I have multiple reels. - Water fill ( 1 reel for fill hose) - 2 pressure washers - (2 hose reels) - 12v softwashing system (1 hose reel) - Comet P40 gas softwashing system ( 1 hose reel) - 300ft of 1/2” hose (1 hose reel)

makes sense@@readykleenpowerwashing

Thank you very much. We’re all in different stages in this business and eventually you can get there if you stick with it.

Appreciate it Tony 💪🏽💪🏽💪🏽

In due time things will happen.