What harness are ya running ?

His neighbors have rock bouncer jeeps lol hp block party

This is genious

Next time use a tractor choke cable. You can get them in whatever length you need then run the cable somewhere convenient.

1 million and 50,000 view all up! Congratulations! Did you guys end up doing the giveaway?🙂

58491 Zemlak Green

That's awesome

Jones Christopher Miller Eric Gonzalez Larry

Good Job guys

Question for ya. I’m swapping my k1500 currently. What did you use for radiator and shroud? I bought a 3 row off eBay and it’ll be coming in within the next few days. I’m running an lq9 6.0 out of a 04 Escalade. Trying to figure something out for upper rad hose mount. I’m not running mechanical fan because I just bought dual electric. I really don’t want the hose just hanging. So any ideas or suggestions would be great! Super cool swap you did!

Robinson Donna Young Betty Jones Daniel

Elena Fort

Let's see the dyno results where you're overlap loses huge horsepower Richard Holden has proven this over and over again it doesn't happen

They want to give you a PD cam did eliminates the benefit of a PD blower it's nuts

A max power naturally aspirated cam will make more power than a turbo cam on a turbo motor. Whatever the cam does naturally aspirated naturally aspirated is what it'll do with boost just more. All these different cams are ridiculous

Colleen Coves

Jakubowski Unions

Dont want to spend $70 buying 1, but i am willing to spend $100 on time and labour to make one😂😂😂😂😂😂

Heidenreich Trail

So badass

i can't wait to see it at raceweek.

After working on bimmers and audis I’ll happily work on GMs

Need to see you refit the trans to the engine before we can judge it.

Nice truck

Hello, I have a 2014 gmc sierra 2500 diesel dealership told me I can buy the TCM(850$) and they charge 190$ to program it. After that all I have to do is install it back and it should be all good again? or is there something else that needs to be done? Mecha inc was charging me 4000$ so I wonder if there is something else that am supposed to do.

I'll be building one of these in the morning. 👍🏻

You Fellers ROCK IT! Love this show! #WATCHTHIS #DRAGNDRIVE #RACERLIFE #DRAGLIFE

If you do the plugs in the towers and run a disabler in the obd2 , will this disable the afm?

That’s a purge valve not egr

Hello I trust had the po700 code on my 2016 GMC Tahoe Tcm don’t look hard to exchange but what about programming how does that work? Thanks

I’m surprised you haven’t gotten any comments on this. This was super helpful. Yoke on my front drive shaft bangs into my 5.3 oil pan and the exhaust manifold. My 5.3 came from an 01 Sierra. Hopefully your c5 vette manifold is the right solution.

its actually a design feature of planned obsolescence well done GM throw that Escalade away and fetch me a new one and don't forget to charge me twice the sticker price - american consumer 🇺🇸🖕🤣

finially found a use for a 9MM!!!

That is soo SICK

I've done a rear axel bearing, front hub assembly, cv axles, fuel pump, alternator and power steering pump. Love my Trailvoy.

Is it in the same position for a tahoe 2015 lt

Small world man I live in that town and work at the Autezone up the road from oreillys

Race car friends

So smart 😂

I follow you. I will wait for you too 😀

where is the TCm on a 2015 GMC acadia

Since you said you parting out. Is the driver side fender available?

Looking forward to doing it all brothers and its a joke my friend did to to get shit started and it well ok later

This should be standard on all 2017 GMC sierra’s, what a screw up from GMC … so many problems, can you share approximate cost? Great job

That seems sketchy... But fun

You can do it on any car just do t spray it in engine cuz most factory vehicles like to blow up from overoressure

You made me feel Better about paying 450 in labor 😂

You can sharpen the blades without removing them? They should be balanced

Same problem my hero 9 black 😢

Where can I buy the transfer case adapter?