Are these on the cm2450 also? Or they updated it?

Where its located I have the same issue. Are you replacing the heater or the element

If it’s a runaway run away

No more repair videos peace

Can this prevent truck from reaching needed regen temps?

1,500 for a compressor gasket ?

Good job sir, I strongly recommend getting in the habit of plugging/ covering the oil supply ports located topside the block (4)

Do you know what normal reading should be of gas pressure sensor?

I have 2010 Peterbilt 389 with a Cummins ISX and is doing the same thing and no active code at all also saying low voltage check everything out and is all good any help I’m thinking about getting a new ECM any help pls thx

New owner here! Appreciate this video.

Mack Anthem is a DEF nightmare!

Hello. Could you please help me, can this unplugged sensor cause bad shifting and not stable idling? Thank you!

Hello. Could you please help me, can this unplugged sensor cause bad shifting and not stable idling? Thank you!

I cleaned the connection with contact cleaner really well then use a tad of dielectric grease, plug it in a few times before you try check it to see if it works properly. Mine worked fine and if it works it saves you lots of money. Don’t remove probe first.

Good job

My truck was failing for about 3 weeks until it died, it had different symptoms the first time it was almost unnoticeable the second time it did exactly what this video shows. Many times it lost power I would restart it and it would turn on and work normally, now that it died it only cranks but does not start and does not activate the fuel pump, fan clutch and rev needle

Can you unplug that sensor to make it to the shop ?

This is awesome job, well done ❤❤ what is name on the application which you are using it.

Air compressor 🤫

You're video's are a little slow.

You're video's are a little slow.

You're video's are a little slow.

Bro,r why you got this video on here, you have no idea what your talking about, you saying you checking the electronic pump not the gear pump

10 diff ways i could have thought of to not have that coolant drain all over the place, and you couldnt come up with ONE way.....i wouldnt let you work on a lawn mower let alone a big diesel engine.

My question is I just got a overhaul with warranty. Would this problem be related to the engine

Where is the egr temp sensor location

Would a bad egr cooler mix coolant into the oil on a isx12n natural gas ?

Where are you located we need help 2020 kenworth t 680 have so many codes.

This truck doesn’t shake at all. The ride is sooo smooth

Thanks

I had a mechanic do a quantity test on mine, he said the doser valve sprayed 100ml of def during the test and that it was within spec. Does that sound right?

How. Much. Is it. Sir

What size. Engine is. It. Sir.

What degree was the mark on gear facing?

Was the truck over heating before you checked it?

I see a lot of Volvos on the road making money. Lemons happen with every brand nowadays. I have a Freightliner which everybody would talk bad about. But I love it. KWs and Pete’s are overpriced in my opinion with lack of service centers. I would own a Volvo. But I would never have a sunroof on anything even a pick up truck. Always a problem

Как уменьшить окна в программе, у меня крупные буквы не удобно читать...

Cummins or Detroit mic drop...

Cummins aint what thhey use 2b either...

I have a 98 t600 with a 12.7 dirty Detroit dependable as hell no def no bullshit...

Paccar engines will ruin u!😮

It’s funny how you just throw money at replacing parts. You didn’t even run the tests through the engine manufacturer software and show how to do the reset. This part is Not just plug and play but it needs to be reset in the software.

Will heating it make it easier to loosen?

Will heating it make it easier to loosen?

Yeah but how do you do it without taking all that other stuff off?

Thank you very much. You’re video save me it really worked.

Been working on this fuel issue for a while now ecm was saying it was getting fp but put a exm from a running engine and ur video was a massive help ty sir

Helpful ❤❤

Just had a head job done on our truck. Got roughly 100 miles from the shop before it had to get towed back. Im wanting to ask you what can go wrong with the assembly after a head job to cause a tick like sound before the oil pressure drops and pushes fuel up into the oil pan?

I'm going to check this on my truck today. I have alot of pressure in my coolant and I just got a rebuild