terence w bird

Пікірлер

@elwoodgreybuffalo5614 27 күн бұрын

Not sure about the picture

@elwoodgreybuffalo5614 27 күн бұрын

Awesome ❤

@mudrunna13 3 ай бұрын

Why does it not comply? What are you basing your opinions on?

@terencewbird2410 3 ай бұрын

Road Management Act 2004, Code of Practice, Worksite Safety-Traffic Management Communications with VicRoads VicRoads MoA (and the clincher) I know who is responsible

@thomasstahl9683 6 ай бұрын

Great!

@falkononskiis4549 8 ай бұрын

The string method is ingenious. Thank you!

@mickawardy 10 ай бұрын

Not a super place to park, not much room with all the guard rail around, maybe worry about yourself.

@terencewbird2410 10 ай бұрын

0.17 shows exactly where I was parked.

@Pw-f100 Жыл бұрын

It's called a Scrivit combination screw and rivet.

@bastogne315 Жыл бұрын

My filter has 160k miles up on it..

@zoomsday3999 Жыл бұрын

Thanks for posting this video.

@BiteMeRightHere Жыл бұрын

Stellar video, thanks

@terencewbird2410 Жыл бұрын

You're welcome.

@lukedieringer9738 2 жыл бұрын

Will this filter work for the 2.3 liter?

@terencewbird2410 2 жыл бұрын

Yes See Ryco website www.rycofilters.com.au/Search/SearchResult?VehicleID=120106900

@harryboeijer6945 2 жыл бұрын

Zoooooooooooooo gooooooood

@dominozonda 2 жыл бұрын

Great video! Really creative and informative I have a 2006 mazda 3 with 230,000 km I was wondering whether it's worth it to keep it and keep fixing it or not What would be your advice? And what was your experience with reliability? My wheel bearings are starting to go bad, also the catalytic converter, and the car is consuming around 1 liter of oil every 7000 km Also the right turn signal lever/switch started malfunctioning a couple of days ago (seem to be broken or stuck) I like the car but I don't know if I should keep putting money in it. Curious to know your opinion

@terencewbird2410 2 жыл бұрын

Thank you for your comments about my video. As far as advice on keeping your car or not, unfortunately I am not qualified to give that advice, as I am not a mechanic.

@dominozonda 2 жыл бұрын

@@terencewbird2410 your methods were so creative, I thought for sure you had experience as a mechanic or working in a similar field It's always tough making a decision whether to continue spending money on an old car or to move on, but I like this car so I'll try to DIY what I can to keep the cost down and hopefully it'll workout in the end How is your mazda 3 holding up if you don't mind me asking? And did you face any problems with it other than the wheel bearing?

@mydogzty 2 жыл бұрын

This has been on of the better KZbin videos I've seen since 2015, just a quality how to and what not to do video nothing crazy edited just how to do the job, wonderful.

@danjoy92 2 жыл бұрын

Thanks!

@unicorn1001 3 жыл бұрын

First heard this song from Wendy many years ago at an AFL Grand Final. It was pure goose pumps. I finally found a download on KZbin. Nobody has ever sung this song better. For me the best version of a really great song.

@jsolo7576 3 жыл бұрын

Nice!!!!

@o0FranklySpeaking0o 3 жыл бұрын

Nice one, thank you 👍🏻

@AutoScan.Doctor 3 жыл бұрын

Thank you very much..

@terencewbird2410 3 жыл бұрын

Glad to help.

@justincameron5902 4 жыл бұрын

I have two grey connections and can’t fit the disconnect insert on the outlet side any ideas

@terencewbird2410 4 жыл бұрын

Justin, I just did this with my "off the car" set up. I severed the filter outlet pipe between the plastic connector and the filter housing with a pair of bolt cutters. I used a pair 24"/600mm long and there was just enough room for the jaws. The next size down I think would be ideal. The outlet pipe was squashed but not cut through but 6 or so movements back and forth and it separated. This allowed me to put two flat bladed jewellers screw drivers under the grey tabs. With the tabs up I used another small flat blade to push the outlet pipe out of the connector levering off the bead on the outlet pipe. I know it will be awkward on the car but it did work. Using bolt cutters does not leave any filings or fragments. Good luck, twb

@georgestamatopoulos4435 4 жыл бұрын

That’s great mate but where is it on the car????

@jayedgerton3063 5 жыл бұрын

Excellent video. All the tricky points are well explained and the solutions provided are cheap and effective.

@teresevella5946 5 жыл бұрын

Thanks mate that was very thorough and very helpful

@gumbyistella 5 жыл бұрын

Thank you Terrence great tutorial

@gav240z 6 жыл бұрын

This was a GT-A not a -B right? It looks like single carb.. Wish I could find these more easily.

@terencewbird2410 6 жыл бұрын

This was a factory 67 GTB, webers, big tank, LSD, the lot but as I used it as an every day drive I put the single carby on. Thanks for the interest. If you are interested there is a Prince Register (car club ) here in Victoria Australia. Also, have you seen this kzbin.info/www/bejne/sHuVpYOvpbOMfqM (sorry for the video low definition)?

@andysmith191 6 жыл бұрын

Are the 1.6 mazda 3 same as 2.0 mazda 3 2004 and 2007

@terencewbird2410 6 жыл бұрын

I don't know. I'm in Australia and we only have the 2.0

@haimantramdial650 7 жыл бұрын

are you selling the car frame?

@terencewbird2410 7 жыл бұрын

Sorry, but no. The front will be cut off and stored for repair sections and the rear section, roof and floor was completely destroyed by the impact and will be scrapped. Thanks for asking.

@theanythingman441 7 жыл бұрын

Hmmm yeeahh....... that ain;t gonna buff out!! the old G7 sounds good though. Cheers!

@theanythingman441 7 жыл бұрын

How 'bout an update on this Terry?

@terencewbird2410 7 жыл бұрын

My apologies, the comment about it being back on the road was completely tongue in cheek. The car was totaled by being rear ended but the engine survived. This video was taken while I ensured that the engine still ran before being passed on to a new owner. The engine now lives in another Prince body and runs just great. Thanks for the interest.

Ең жақсы KZbin

Пікірлер