She made getting the 3 bolts in look easy. Took me a couple swear words and some sweat to line up the 3 holes. 🥵

That sounds like SHIT!!!!

I have a Rugged Radio pumper now one complaint I have is how much it heats the air up. Does this one do the same thing?

Does this require a tune?

Wad that a direct fit

Would like a better camera angle on the pin by the throttle body. No visual on that.

Hey Andrew good to see more content. Did you decide to keep it? Thought you sold it for the green Ram??

I just got a 2024 xp 1000 sport and I’m definitely going to invest in your product

Very helpful

I first saw these mounts a couple years ago. Pricy but you generally get what you pay for, and if they last longer that the Factory mounts, you are money ahead. I have watch a few video`s on these mounts, and see a 2014 truck, to me that is pretty new as I drive an 86 F-250 6.9 Diesel, owned past 10 years and now have 351K miles on her. I know the cab mounts are long gone, as after 38 years should be, and probably be a bear to replace. Most likely metal to metal as the rubber is long gone....LOL. Iam 80 and will be diving into this project this fall, if i can do it, anyone reading this has no excuse`s as to why they cannot. Great video you did on replacing them

Do you have performance before and after testing?

This product is now available to purchase?

Is this going to be available soon?

So where is the independent dyno tests ,that prove this intake makes more power than the oem intake?! Asking for a friend

I installed my S&B Helmet Pumper in the exact same location as you guys did. Even before this video was around to help. I have the center scoop too so it was about the only place I could install it. Very easy installation.

Yeah man. YEAH

I may be in the minority...but I have installed a Backwoods Adv Mods Nomad Rear Bumper, which is lower than the pinch weld you show for mounting the hose. I'd need that mounting bracket 3" taller to bring the hose fitting down so the hose doesn't kink when filling. I suppose I'll just bolt on another plate as an extension unless you have another idea.

Mpg increase?

Mpg increase?

Mpg increase?

Seems like I'm not the only one who clicked not knowing what the actual product is She's just that dang pretty

FYI there is a line near/above the top radiator hose 0:33 that supplies fresh air back into the valve covers, 2 lines run from each cover to a T and it goes to intake tube. (can be seen at 1:52 above his wrist parallel to the PCV hose disconnect from intake earlier) Slide clip and it pops off. Make sure its connected back or it will throw code due to un-metered air not crossing the MAF sensor.

URGENT! Accidentally put the wrong fuel in the ford. Is there a drain plug on this tank. If so where is it located.

Thanks for the vid. Got mine in no issues. Exhaust upgrade next.

Hey S&B team. I have your 45gal sprinter tank and love it. My van is mostly for track day support and I was thinking about putting this tank on my sprinter to put gasoline in it for my track car. Obviously I need to think of a way to safely pump fuel in/out but would the tank itself should be safe for fuel???

Why did you stop making the ram air scoop for LBZ ? Id hate to modify a Banks scoop to mesh with your kit .

Very knowledgeable and helped me mentally prepare for what I have to do thank you

How much those parts set you back?

Great video, 20 minute install...easy peasy

My hard plastic lid keeps popping off when I accelerate. Any reasons can’t seem to find the issue

What do this exactly do to the vehicle?? What’s the difference???

Does it work on hybrid silverado 2011?

I just had this tank installed in my 2020 F-250 went to fill it up and it started leaking. Has anyone had this problem before? I had it installed by a shop in my location. They said it was the O ring that comes with the tank manufacturer 🧐.

snorkels?

What happen to Katie?

So where, exactly, is the "cold air" coming from? The same exact place the stock intake is getting its air from!

Good install video thanks! That little clip is a bugger..lol

How do I calibrate the cluster to tell the computer it’s a 60 gallon tank for DTE, 2008-2010. Ezlink only works 2011 and up . Thanks in advance

Will using a EDT additive like hot shot or Docs keep it cleaner?

Throws check engine light!

That was a great install video. Best I’ve ever seen.

Thanks for sharing.

Which Ford Transit model?

That's a gorgeous 2 tone diesel. I've got the green/tan.

👍

I want you to be the mother of my kids please.

Does this hang lower than the 52 gallon tank? Would be awesome to see a comparison between the 52 and 55

literally sounds identical

When he says "you're gonna have to figure this one out on your own" at around 12:20, he means to say: you might want to take the bumper off to make it easier. The music is distracting and your fatigue by the time you made it to the front/engine bay mounts made your explanations appear short and frustrated. Thanks for the video and a great product.

Will you marry me....PLEASE!!???