Great video. Could you tell me where the AC actuator is?
@davidhastings7714Ай бұрын
great video. Is there something else you can use instead of mastic in a smaller tube maybe?
@greatdane33433 ай бұрын
Great info, especially the clips. Thanks for sharing.
@edwardphelps51297 ай бұрын
will it be the same on a 99 105 series?
@albertojonloo5344 Жыл бұрын
Hi. Can you tell me the part number of the smal square module that its screw on the cover. 1:42sec. Its missing on my lc and cant find more info of it. Please
@ultracoolautomotivecarairc3705 ай бұрын
Antennae ECU.
@luluandlama7184 Жыл бұрын
What sealant are you using? Is that windscreen sealant? Great vid, thank you!😊
@ultracoolautomotivecarairc370 Жыл бұрын
The link for Selleys D-mastic has been updated in the description.
@dirkholthaus2231 Жыл бұрын
I just did that to my 105 , after a guy quoting me $3000 to do it recons the whole dash needs to come out and remove radiator to get the condenser out , saying it would take 3 days . I managed to do both in 3 1/2 hours. The only thing is i used the old o rings .
@yallawallahalla Жыл бұрын
Nicely done mate. There are far too many thieves in the industry! How does your AC perform after the swap?
@dirkholthaus2231 Жыл бұрын
Absolutely beautiful, the only thing it sometimes squeals it sounds like fan belt slipping . Might have to tighten it ip a little more i just hope its not the compressor giving up
@yallawallahalla Жыл бұрын
@@dirkholthaus2231 amazing. Thanks mate. Was it getting cold at all before the change? Mine looks like it’s full of leaves and dust ect as there’s no cabin filter.
@dirkholthaus2231 Жыл бұрын
Na wasn’t getting cold at all condenser was absolutely stuffed, I stripped out the divider and installed cabin filter what a difference .
@yallawallahalla Жыл бұрын
@@dirkholthaus2231 love your work mate. I was about to take it in To a specialist and pay big money. Will give this a shot instead. 👍🏼
@kenbina Жыл бұрын
This looks like a piece of cake compared to the job done on a Range Rover L322 for the same issue. 🤦🏼♂️
@sbulla652 жыл бұрын
Good Video, I have a 02 model and it has no cabin filter, I have seen on youtube parts can be ordered for the left hand drive model to up grade the cover to fit a filter. Have you done this on a Right hand drive model, or do you know if the parts are available to do this? or can you supply the parts. Much appreciated and thankyou in advance. Steve B
@ultracoolautomotivecarairc3702 жыл бұрын
Not available as we know but could modify the box to fit one.
@ultracoolautomotivecarairc3705 ай бұрын
There is heaps of info about retrofitting a filter in LHD & RHD 100 series. Google and KZbin is your friend.
@XDSmelliot2 жыл бұрын
What's that metal bar that goes across the bottom - where the glove box mounts to? I presume you cut the plastic stock one out and fabricated this as a replacement? Aside from what you've shown in the video would you do any other work if the evaporator needs replacing?
@zoran69882 жыл бұрын
Glovebox support bracket from toyota
@XDSmelliot2 жыл бұрын
@@zoran6988 is there a part number? Mines plastic and from what i read needs to be cut
@zoran69882 жыл бұрын
Yes they need to be cut, if you look closely there are cut marks where to cut. Not to sure on part number
@ultracoolautomotivecarairc3702 жыл бұрын
Some models have already steel bracket fitted (presume air was fitted in au). The plastic cross panel one had the dash out when fitted. Normally would cut the drivers side of plastic on the indent (distinctive) and put small steel plate behind it then fasten from front with screw to reinstall.
@ultracoolautomotivecarairc3702 жыл бұрын
@@XDSmelliot please read my (late) response above/below/somewhere.
@slow_diver2 жыл бұрын
This is excellent. I assume to know the evaporator/condenser isn’t working, even fully gassed it’s not cooling? Thank you for the explanation👍🏻
@ultracoolautomotivecarairc3702 жыл бұрын
The system is tested before work is done. Dye is added to the refrigerant gas. A few days later an inspection under UV light may reveal a gas leak.
@marchettler54562 жыл бұрын
Looks labour intensive. How much does the procedure cost if a mechanic does it? Rough estimate would be great
@ultracoolautomotivecarairc370 Жыл бұрын
Around AU$800 including parts.
@guanghong7162 жыл бұрын
What type of sealant did you use ?
@ultracoolautomotivecarairc3702 жыл бұрын
Edit: The link for Selleys D-mastic has been updated in the description.
@richardbaglieri40103 жыл бұрын
Hi I have the same model but I'm wanting to know how to take the blower fan out if your able to help. Cheers
@ultracoolautomotivecarairc3702 жыл бұрын
If we do a blower unit we'll do a video. Not a common thing.