Threestones

Пікірлер

@zutp090 24 күн бұрын

how difficult is it to remove the old one?

@threestones9782 22 күн бұрын

i need for first time to remove it about half hour including prepare the tools and to located it....

@zutp090 16 күн бұрын

@@threestones9782 I have just tried for 2 hours to remove the old bolt and it seems completely stuck.. Any ideas on how to loosen the old bolt? thanks!

@threestones9782 15 күн бұрын

@@zutp090 i can't understand, how it happend, my boltwidth is 24mm, just use joint and extend and torque wrench with patient to find it, it is not easy to be find.

@zutp090 15 күн бұрын

@@threestones9782 Sorry, I was unclear. I found the bolt, the problem is that it is too tight and stuck to the engine to loosen. I may have to buy a bigger wrench or find some way to loosen it.

@CindyMichelle-js1ub Ай бұрын

❤

@jester-lester 2 ай бұрын

I had the same vibration from exactly the same place on my 320D F31, I did a temporary fix with a long tiewrap (cable tie) around the collar of the air box.

@threestones9782 2 ай бұрын

that is a good idea.

@threestones9782 2 ай бұрын

Internet

@fbi5737 2 ай бұрын

Where did you buy new tensioner?

@GOUNIPRAVALIKAREDDY 3 ай бұрын

can u share this design files

@WilliamRaper-r1z 3 ай бұрын

What a bloody pantomime.

@iambenmitchell 5 ай бұрын

FYI if anyone is doing this in the UK, Mr Muscle oven clean works amazing at cleaning off carbon. Currently doing it now and it has cleaned my intake manifold and EGR valve without any effort. I used about 2 cans

@gordonho5986 6 ай бұрын

What's the recommended amount (Liters) needed for a complete flush and top-up for an F55?

@threestones9782 6 ай бұрын

less than 1 liter

@undergroundlegend198 7 ай бұрын

Good people do not touch the egr it's not worth damaging the engine if you have no error codes keep driving

@R_Syndikat 8 ай бұрын

Ich hab den AGR geschlossen und auscodiert, bei meinem Diesel kann so was nicht mehr vorkommen! 👆😉

@threestones9782 8 ай бұрын

Top, wie geht es?

@cedriccc3925 8 ай бұрын

Thank you!

@cedriccc3925 8 ай бұрын

Thank you!

@kevinprivet5942 9 ай бұрын

Amazing, what clown school did you attend, you numpty?

@shiray87 9 ай бұрын

Nice video, gonna habe to change the bearings on my Haier. Did you have to change the seal on the drum? I am not even sure, if there is one...

@妞妞秀 9 ай бұрын

Better ues new one, but if it is in good condition, the old one could be use again.

@igortanyarascovschi1225 9 ай бұрын

if I rotate the crankshaft pulley to clean the valves, does it matter the direction ? and once i finish the job and the valve of the cylinder 1 is not in the exact position to the ignitión, this could be a problem or the digital electronic adjust it automatically? could you please reply

@threestones9782 9 ай бұрын

the direction is important

@igortanyarascovschi1225 9 ай бұрын

what do you use (grease, oil) before puting everthing back? I see your using some oil with the brush Thank you and await your reply

@igortanyarascovschi1225 9 ай бұрын

What is the inlet canal youre talking needs cleaned for better mpg? Thx

@KI.Kuenstliche_Intelligenz 10 ай бұрын

Deutsch kaka

@mikikrijestorac305 10 ай бұрын

Kann man die selbe Waffe zu dir schicken, weil ich will nicht ein Fehler machen bei meiner?

@macchi205 11 ай бұрын

Puahh..

@Jonnzor Жыл бұрын

Recently changed my F31 rear diff and couldn't work out why my parking brake was loose, even though all the cables were fine. Used your video and checked the spring in the parking brake lever. Found it retaining tension. Released the spring and the parking brake is working again! Thanks mate!

@freigeboren5424 Жыл бұрын

tolle Kameraführung, super Audio, ironie Aus.

@oxafrummel8221 Жыл бұрын

Ziemlich langweiliges Video

@heavoc9793 Жыл бұрын

A LOT TOO FAST

@DanielGONIN Жыл бұрын

Please Help me !! I can not unlocked the Head printer coz i want to clean

@keldpedersen9566 Жыл бұрын

KN jeg vaske børstehobedet

@tempkinvient Жыл бұрын

Thank you for saving me from my own stupid attempt to dissassemble

@saichowdary7186 Жыл бұрын

How to remove those plastic caps covering the screws

@bb7609 Жыл бұрын

Hi can you tell me the part number please

@WeAreN1nja Жыл бұрын

Bro. Thank you. I had to watch way too many vids for this information.

@dr.mazinga1868 Жыл бұрын

Grazie :-)

@mrm4079 Жыл бұрын

Right guys, I coulkd not get the back on this watch for love nor money!, Its very very hard, someone on here(sorry I forgot where I saw your helpful post) advise this: Use a rolling pin, (UK) the thing you roll our pasty with. Put your watch on a hard firm surface protecting the glass face obviously. Line up the back with the winder cut out, roll over the back with the rolling pin Voila, worked for me.

@naomimedina3645 Жыл бұрын

How do get the thingy to move

@noobontour3167 Жыл бұрын

What is the spring relise for

@TheGamingDragon0 Жыл бұрын

Anyone could help me? My motor is buzzing and not shooting. When I looked on piston and spring it almost looks like not enough power. To fully bring piston back. And inside, brand new batteries and gun in not old and has been cared.

@MrPaloompa 7 ай бұрын

exactlly my problem too ....

@TheGamingDragon0 7 ай бұрын

@@MrPaloompadang bro, if you find a solution could u rly please tell me? I would absolutely love to get this thing running up again

@DonDoko99 Жыл бұрын

Thank you !! I do not have to buy new MQ7 upper parts because of your video! In my situation, some of the gears were out of alignment.

@threestones9782 Жыл бұрын

happy to hear that, that is the sense to make the video to help others

@nanjiang1953 2 жыл бұрын

真厉害

@threestones9782 Жыл бұрын

小意思

@MarcelHVAC Жыл бұрын

小意思@@threestones9782

@kardatoulis9227 2 жыл бұрын

Where did you find those new gears?

@threestones9782 Жыл бұрын

take a look on internet ebay or so

@familiaalfarorequena2631 2 жыл бұрын

How to remove the panel where the TFT is. It stopped working and it's blank. Are the contacts dirty? Or do I need to change the entire TFT panel? Any suggestion. Thank you very good your video.

@threestones9782 Жыл бұрын

i don't think so