21 күн бұрын
2 ай бұрын
2 ай бұрын
Пікірлер
@CCAssurich Күн бұрын
❤👍
@andersonluisoliverio515 4 күн бұрын
Ótimo trabalho,
@CCAssurich 4 күн бұрын
Thank you for appreciating it 🙏🙏
@ZoneTelevision 10 күн бұрын
This is awesome.
@CCAssurich 5 күн бұрын
Thank you🙏
@deven6518 Ай бұрын
How much material?
@CCAssurich Ай бұрын
60microns
@janicepayac1 Ай бұрын
👍
@janicepayac1 Ай бұрын
😮
@CCAssurich Ай бұрын
❤
@anthonytumbarello9940 2 ай бұрын
I think you are increasing the center to center length of the rod, but by how much?
@CCAssurich 2 ай бұрын
Yes sir exactly, this process is increasing the rod length total of 2mm increase. But in this video 0.50mm only because the 1.50mm I offset during counterbore bigger on the rod small end, which I already upload the video recently counterbore process.
@danilomaravillas7785 2 ай бұрын
Nice good job
@CCAssurich 2 ай бұрын
Yes sir, thank you for watching! 😊
@danilomaravillas7785 2 ай бұрын
Your welcome sir
@ВладимирКорабельников-ъ4х 2 ай бұрын
Да , если делать такую работу , тиски должны быть станочными , как здесь. С минимумом люфтов , исключающими подъём подвижной части тисков .
@CCAssurich 2 ай бұрын
Yes sir exactly and this Vise I am using is a precision vise. This method is quite good.
@thehinac01 2 ай бұрын
high rev much?
@CCAssurich 2 ай бұрын
Long stroke short block frome 5 liters to 6 liters engine upgrade.
@bigblockjalopy 2 ай бұрын
@@CCAssurich"upgrade"? No. Measure the rod angle at bdc and be prepared for another rebuild 50k from now ;)
@CCAssurich 2 ай бұрын
Okay sir noted! Thank you for reminding me. We do hope everything will be alright🙏🙏
@AhYoung-u9h 3 ай бұрын
Máy móc chạy tốt
@CCAssurich 3 ай бұрын
Yes sir, CWT balancing machine very impressive👍👍
@jayengineeringheadrepair7360 3 ай бұрын
Ap wuman hoke machine clarhi ho muje kshi huvi
@CCAssurich 3 ай бұрын
Yes
@jammasterjay 3 ай бұрын
Fixturing is an art form of its own.
@CCAssurich 3 ай бұрын
Yes sir
@DhalipBeharilal 3 ай бұрын
Great job sir what car oil jets are u using for this application
@CCAssurich 3 ай бұрын
Thank you sir, Im using the 4age oil jets sir.
@nowere4579 4 ай бұрын
Nice neat work!!
@CCAssurich 4 ай бұрын
Thank you🙏🙏
@BogdanovBros 4 ай бұрын
Малый зазор
@CCAssurich 4 ай бұрын
Little bit can😂😂
@RAzzzbojnik 4 ай бұрын
крутая приспособа! надо сделать
@CCAssurich 4 ай бұрын
Thank you
@DanielRamirez-vi8nq 4 ай бұрын
Bien hecho Su servidor en estos casos de deformación Rectifico de 0.002" a 0.003" y se verifica la medida con los cojinetes intalados y sobre de esa medida se rectifica el cigüeñal con la medida que muestra esl micrómetro Para dejar la tolerancia que me especifica el fabricante En ocaciones tengo que dejar el diametro más grande. Saludos desde Zapopan Jalisco Rectificaciones Tepeyac
@CCAssurich 4 ай бұрын
Yes sir, thank you
@premjitsingh36 4 ай бұрын
It's not Toyota Supra it's some diesel engine
@CCAssurich 4 ай бұрын
Yes, this is for supra sir a petrol powered engine
@benlopez9584 5 ай бұрын
Thank you for sharing your knowledge it's helping a lot more power to you and bunch of videos like this soon🙏😊
@CCAssurich 5 ай бұрын
My pleasure 😊your welcome sir! I will continue to share and more inspired because got people appreciate it.🙏🙏
@rosie1964 5 ай бұрын
Those sleeves are "HARDENED STEEL " !!! but that one is Not Now !! 350° - 450° is more than enough... heating till red hot (900° at least) removes the hardness
@vishS14 5 ай бұрын
Exactly, So many vids of people ruining metals, thinking they're smart
@CCAssurich 5 ай бұрын
Yes sir, thank you for your good suggestion by sharing your knowledge. Highly appreciated🙏🙏
@ftboomer1 5 ай бұрын
Beautiful rebuild. Absolutely exceptional
@CCAssurich 5 ай бұрын
Thank you very much!
@cyborgc4799 5 ай бұрын
Look like your shaft is bent
@CCAssurich 5 ай бұрын
The small boring bar when cutting big will a bit waggle but this is a high carbon steel and hardcrome plated it will back to normal straightness.
@CCAssurich 5 ай бұрын
If you talking about the crankshaft sir, yes its badly bend.
@ikramuddinuddin8758 5 ай бұрын
Head wark and aluminium tig welding
@CCAssurich 5 ай бұрын
Can also
@ikramuddinuddin8758 5 ай бұрын
Hallo sir wark Bahrain all engine line sir you have vacancy for me
@CCAssurich 5 ай бұрын
What engine usually you do there sir?
@DhalipBeharilal 5 ай бұрын
U are a a master sir u take pride in ure work
@CCAssurich 5 ай бұрын
Thank you sir🙏🙏
@kiranshukla6834 5 ай бұрын
Where are you from?
@CCAssurich 5 ай бұрын
🇵🇭but working here 🇲🇾
@CiprianoJr.Ciruela 5 ай бұрын
nice work!
@CCAssurich 5 ай бұрын
🙏 thank
@MuhammadFaisal-jf7dt 5 ай бұрын
just imgine…weighing 2.5 kilograms less an engine b20a...how much hp can make? in rnge 9-10k rpm
@CCAssurich 5 ай бұрын
The number I can’t give you exactly sir the garrage can explained that well, all we did is the process of machining that can make the engine reliable.🙏🙏
@DanielRamirez-vi8nq 5 ай бұрын
buenas noches muy bien en inserto de buje de biela gracias
@CCAssurich 5 ай бұрын
Your very much welcome sir, thanks you appreciate and like it😍😍
@EmilKto-cb2df 6 ай бұрын
Normalnie jak w Pakistanie, *tylko" sterylnie czysty warsztat 👍
@CCAssurich 6 ай бұрын
Yes sir, thank you
@EmilKto-cb2df 6 ай бұрын
@@CCAssurich naprawdę świetna robota! Ludzie muszą nauczyć się naprawiać a wysoko wykwalifikowanych fachowców coraz mniej. Pozdrawiam i zdrowia życzę! 🤝
@CCAssurich 6 ай бұрын
Highly appreciated sir, ounce again thank you very much🙏🙏😍😍
@HendriaWinarti-gv4fi 6 ай бұрын
Ini bengkel berada di mana
@CCAssurich 6 ай бұрын
Bandar Sunway
@cyranox90 6 ай бұрын
Nice… how do you cut the oil groove after welding?
@CCAssurich 6 ай бұрын
Thank you sir, a bit complicated to cut I still using the line boring machine.
@cyranox90 6 ай бұрын
@@CCAssurich do you mind sharing it next time you upload a video? Also, when grinding a crank, how many mm you move the wheelhead to grind, remove 0.10 mm at once?
@CCAssurich 6 ай бұрын
No problem sir, coming project r34 RB block want to do the oil groove in the main housing I will show it how using the lineboring machine.
@CCAssurich 6 ай бұрын
When grinding the crank for me we have to know the capacity of the machine some can move sideward even cutting big without vibration. For safety have to left around 20microns for finishing.
@cyranox90 6 ай бұрын
@@CCAssurich thank you so much!
@MirzaShafiq-j2o 6 ай бұрын
MASHA.ALLAH.GOOD.WORK
@CCAssurich 6 ай бұрын
Thank you🙏🙏
@imadahmmad1965 6 ай бұрын
Nice job first time see balance machine
@CCAssurich 6 ай бұрын
🙏 thank you
@vyacheslavkorolev2758 6 ай бұрын
This is the first time I've seen such a job done without a CNC. This is a very high level of machine operator.
@CCAssurich 6 ай бұрын
Thank you sir🙏🙏
@nonanano5283 6 ай бұрын
Pretty Christina Awesome equipment Where is it?
@CCAssurich 6 ай бұрын
Bandar Sunway, Petaling Jaya
@nonanano5283 6 ай бұрын
Nice equipment
@CCAssurich 6 ай бұрын
Thanks 👍
@manikuppusamy-dv3hz 6 ай бұрын
Super
@CCAssurich 6 ай бұрын
Thank you sir🙏🙏
@besawanathanmwawesi9560 6 ай бұрын
Good video guys...❤ Where are you guys located??
@CCAssurich 6 ай бұрын
Bandar Sunway PJ Malaysia
@KenFullman 6 ай бұрын
Was this perhaps caused by overheating?
@CCAssurich 6 ай бұрын
Yes sir, a lot of factors to consider and overheating is one of those. When the engine overheated the temperature goes up and when the engine is very very hot can cause a lot of internal parts clearances changes and the engine oil also becomes very thin and if the oil is very thin the oil pressure drops. If the oil pressure drops can cause insufficient oil supply to the bearings.🙏🙏
@CiprianoJr.Ciruela 7 ай бұрын
awesome work! very detailed.❤
@CCAssurich 6 ай бұрын
Thank you! Cheers!
@mmahmud2695 7 ай бұрын
Kristina
@CCAssurich 7 ай бұрын
Yes sir
@mmahmud2695 7 ай бұрын
Kristina from indonesia
@CCAssurich 7 ай бұрын
Yes sir, now she’s doing her own.
@cyranox90 7 ай бұрын
Where is she from?
@CCAssurich 7 ай бұрын
From Indonesia sir.
@cyranox90 7 ай бұрын
@@CCAssurich which city in Indonesia? Very rare to see a lady in this field
@CCAssurich 7 ай бұрын
Yes sir, Pekanbaru City, Sumatra Island. They have there own machine shop there also.
@cyranox90 7 ай бұрын
@@CCAssurich is Berco machine still being sold?
@CCAssurich 7 ай бұрын
Berco machines are very impressive for engine rebuilding but I think they are no more in production already now.
@Msali92786 7 ай бұрын
Great 😊 work.
@CCAssurich 7 ай бұрын
Thank you! Cheers!
@Msali92786 7 ай бұрын
We keep clearance for the heavy duty engine 0.004''
@CCAssurich 7 ай бұрын
Yes sir, 0.004” is very good and safe clearance and that was also our maximum target. But we choose to go for the minimum side as long as can spin smoothly. Thank you sir🙏🙏
@ngeo88 7 ай бұрын
Should be in Malaysia, work shop listen to Mandarin song but written "Rosak" meaning broken on some piece of object 😂
@CCAssurich 7 ай бұрын
Yes sir, but “rosak” is in bahasa language as it meant exactly of what is your definition. This we broke into pieces but we rebuild back to be more powerfull and reliable engine.🙏🙏
@Msali92786 7 ай бұрын
Great 😊
@CCAssurich 7 ай бұрын
Thanks 😊