My guy, this was not a trans removal video. Disappointed.

Nice job Sir

Always stop drill the end of a crack to stop it from spreading further. When painting plastic, using an adhesion promotor will do wonders for longevity.

Jdm cleannnn

So what size reducer and what size exhaust flange did you have to weld on? 3-2.5 inch with 2.5 inch exhaust flange? Or 2.25 inch?

What downpipe did you end up going with?

I wanna do a jte swap on something. I'm in hawaii so finding chassis is hard and a conversion is a pain mechanic by trade but don't now how to weld. Turbo flanges motor mount shit like that going be costly

Man this does not help me at all I was looking to see if you would film the video showing you removing the transmission. Did you use a transmission cradle on the floor jack to drop the transmission or just a floor jack alone?

How much power you make with this build?

Whoa I'm from Idaho

where did you hook up the green wire two from the clutch switch

i have a few questions what do you mean by “need to take out” and the connector on the clutch pedal where does that connect to?

did you need a manual engine harness v

You get this thing on thw road!?

Yo Ik it’s been a few years since the install😅 but what screws did you use to set the wires to the resistors ? But great tutorial I just got my EDM tail lights and about to throw them on and any problems with the tail lights after this whole time ?

This method will last about 2 to 6 months. I recommend do this method THEN spray 2k clear coat on it, it will last for years. You can buy it on eBay for about 26 bucks a spray bottle.

I want to see more of the 300zx

You still have the trans ? The automatic

Meanwhile here I am in Spain looking for the US taillights... WTF

goosebumps

Was literally so stoked when I saw my car in it, the white celica in the rev off, felt like I actually made an impression!

Bro this guy stoned asf frrrrr

Will you allow to use your video in youtube?

How did you get the flywheel off?

not crazy about the act2600.. does not disengage well and is hard on the clutch pedal assembly and very touchy to get it working right....I have the same disc with the SB x pressure plate very nice so far ...The act 2600 w/street disc held 490lbs torque (mustang dyno) for about 5000 miles.. Now pushing 550 torque on E85 so we will see if SB can do it.

How easy would you say to do this? I seen people saying you can only replace the clutch by pulling the motor

the name of the body kit please

You messed up, the ACT 2600 only holds 415tq now if you went with the full South Bend Clutch kit, torque rating is 460tq. Not to mention a hard pedal for no reason and in the results of poor engagement issues. When you read or hear DSM guys talk about using an "extend rod" for the slave cylinder, shimming the pivot ball for more leverage that's all because of ACT. The 2100 and 2600 clutch disc are the same 🤷🏻‍♂️ACT decided oh let's put a heavy pressure plate and that should give more clamping force. I been a DSMer for 21 years, I've dealt with ACT for many years and I have to say the 2600 is trash. Not everything ACT make is no good, the flywheels are 👍🏻. But there are better clutch companies out now that are way better than ACT with a better pedal feel and no non sense of "extended rod" BS either. My brother's 1g Talon cranked walked a 6 bolt because of that terrible 2600 clutch, switched to the South Bend stage 3 Endurance and he loves it. I switched and never bought a ACT again, I don't mean to rant but it's just my take on ACT. You did good on the clutch disc and but not so good on the pressure plate.

How much is it to get the parts

Inst girl?

Such a great video! You made it feel like viewers were there, watching this! I vote for you to be the new official sharkfest recap videographer!

I need to fix my crack lip too lol. Do you recommend using primer before the actual paint?

In total how long do you think it took you to do the manual swap and what do you think it would cost to have a shop do it for you?

Great video and well explained.

Do u have a link to the instruction write-up you followed??

🤦 p̶r̶o̶m̶o̶s̶m̶

hey man, the video is very instructive and very helpful, i also have EDM taillights on my 99 Gs and did the wiring installation following the same procedures as you, also the 2 8ohm 100w resistors, but my lights ended up hyper flashing. With a tester I checked the base of the corner lights on both sides, and it receives power and flashing, but not the bulb, any idea why it hyper flashes.?? (the bulbs are fine)

Absolutely stunning, and I see myself in line.. 🤣

your color grading is so nice !!

Badass🔥🔥

Epic aftermovie my man, great work

Hell yeah bro sickk

Noice

Best video and guy I have ever seen … but bro .. is it possible to repair carbon fibre lip splitter ? Mine got cracked a bit

I'm proud of you <3

Keep it up 👍

Awesome work bro 🔥🔥

Fire bro 💥

Absolute fire🔥🔥

Thank you so much again !!