What am I missing. I've been driving for nearly 40 years and I've never personally known anyone's brakes to fail. Forget to apply parking brake and roll down a hill maybe but the actual stoppers... Never. Maybe that's a UK thing because of the MOT system we have.

I have the same setup Mustang 2 , Could you help me , I have a 54 chevy ...I need to find the right steering hoses for the rack and rack and pinion , Thank you

Where did you get that small spring for the cable what size is it ?

Great video and God BLESS you for the great explanation. Doing my first LS engine build and everything is smooth except for now that I’m adjusting these rockers. God will provide though!! Thanks for the awesome video

Fatman is out of business now..

I just bought a car with a turbo 350 transmission and the guy said it leaks almost a quart a month, I’m going to get it jacked up and check that out and hopefully it will stop

Old cars matter 😂👍

I always leave the intake cover off and dump a quart or two in there also.

Lock tight not teflon?

ok so if my TV cable is set properly but my 700Rr wont up shift to 2nd 3rd or 4th? what then

Watch out for those seal remover tools. Maybe there are different hook styles but the one I used scratched the side of the housing removing a Pitman shaft seal. The pitman shaft seal is smaller than this tailshaft seal so maybe the angle of the remover put the pointy end of the seal puller hook against the housing. I have to do this for my leaking tailshaft so maybe I'll round the hook off if it looks like it's going to press against the housing. Or maybe there's a better way to use the puller by just hooking the seal.

Wow!!! Amazing video!!!!

we have clearance clarence 😂😂

Thank you for your informative video.I have a 77 Vette and the carb seems like a mysterious object that I really do not understand.Your vid pulled back the curtain and working on it seems less daunting.

As you realized it's a parking brake. Hope you find a backup solution (and share) for a emergency brake. Im in the same boat as you. BTW great job on the video!

We've got our TV cable to correctly shift but have no passing gear and ohhh have we've been struggling to get it to work. The spring will take care of this?

Update both kits are now around $800 for everything in your video on ebay, same cheap china crap🫠

Send that Helix kit back

1 valve brakes damn it

The edelbrock electric choke works backwards compared to a holley. it actually contracts the spring i believe instead of expanding. I know this because my new holley came with a dead choke and i tried to swap my edelbrock and realized it wouldn't work because they work opposite of each other. I had to order a new choke. Holley was zero help by the way.😡

i need a diagram for a e38 pcm .great video

It’s so nice to see a how to video on this. Especially a how to of someone in the same area that adjust to the same climate

Ya got to do it on my towncar

Good to c ya .. keep up the Videos. Lots of good information 👍 on the taps , engine prep , clearances, ECT .

Been missing your videos, looking forward to the build!

wow ! Where have you been ? You taught me what I needed when I r& restored my 55 door hinges. SO BAD, the rusty bolts had to be air arced out of the pockets....... all went well enough the hinges were salvaged. Stripped them, gave them rust patina, clear coat & I'm good. Thankful your here

Great test. Helped out bunches

Hey man, God bless you brother! I hope this message finds you well. Been watching your videos for years now and just now noticed, you use a wheelchair? I thought, let me see his older videos and sure enough, the chair is there. My point: I’ve watched your info, so close that I never noticed the chair until today. Amazing content and strength! God bless you, brother!

What if I have no speedometer cable? Can it leak from that

I didnt get my stimulus check till 3 years after covid haha i randomly got it on my bank account i was ljke wtf is this?

Does anybody know the name of that connector I need one for 06 Pontiac G6 2.4

Same thing for a 2007 Tahoe?

You can actually run the wire to your R terminal on your alternator….

👂🏽🎵🎶🎵🎵👍🏼😎 sounds of success!🏁🏁🏁

Have a Heidts on my '34 Ford. Beautiful ride and quality.

I really appreciate that you took the time to do this. Great review

Great video I haven't messed with a carburetor for a while, your video helped out immensely. Thank you for sharing this!😊

Great video.

Well done! Great video. I would never live under an HOA.

You read reviews that they tend to leak so you install it anyway?

Im stuggling… the small crack between rim and tire 🛞 has been a problem… not easy

You’re in a wheelchair!? Wow man good for you! Great video, thank you.

Can i use thing like clear coat and other silicon strays to protect it

Thank you for taking the time to explain this. My first LM7 truck engine I did, I just had the heads cleaned up at 5 thou which the lifter could compensate for. I also had a valve job with new everything except the seats, those were good enough to just re-cut. Found out my stock 7.400 rods would have been to long and give me .125 of preload. I also went with a Melling MTC7 cam.

Thank you for taking the time to explain this. My first LM7 truck engine I did, I just had the heads cleaned up at 5 thou which the lifter could compensate for. I also had a valve job with new everything except the seats, those were good enough to just re-cut. Found out my stock 7.400 rods would have been to long and give me .125 of preload.

Thank you. The problem I was having was solved withr video. Clear, conciece instruction.

Trans i just bought has a Transgo hydraulic lockup kit.

Thinking about doing to to my 11 sierra

I just checked and I got very lucky! my 1983 Camaro has a two wire solenoid

👍🏽thanks 🎉