TechRally

Пікірлер

@regisdei Сағат бұрын

Are you able to share the Configuration.h or show which lines to define and update?

@xkeno123x 3 күн бұрын

None of my XYZ moves

@TechRallyofficial 3 күн бұрын

Download firmware for correct version of your mainboard

@davidbilec3009 7 күн бұрын

this is not 5.1 its simply bridged stereo sound to a 5 speaker and 1 "sub" connection. It is not surround sound which 5.1 is but youre instead just surrounded by sound which is not the same thing.

@TechRallyofficial 6 күн бұрын

Its true 5.1 Audio not the bridged or simulated 5.1 sound. See the video fully, i used the 6 channel output from PC which has seperate connector for front, rear, center and sub...

@H-HEDITS-w2y 11 күн бұрын

5.5volt 0.5 uf capacitor use in light

@mrburns366 Ай бұрын

I wonder if they would work inside an enclosed 3D printer for FDM and resin fumes? :)

@TechRallyofficial 29 күн бұрын

No, it won't work because fdm and resin will release some PM particles i think, This will not filter PM particles. But i was making one air purifier for FDM enclosed print with HEPA filter. Which will upload in upcoming weeks.

@zuzieeeeee Ай бұрын

Not going to lie man, spent way too long and some wasted filament trying to figure out if I needed a separate bracket for my CR touch before I found this video. Thanks my man! Extremely helpful.

@TechRallyofficial Ай бұрын

Thank you friend 😃

@ErickTorres-xn6bm Ай бұрын

Sir how long the battery last

@TechRallyofficial Ай бұрын

16 to 18 hours

@ParkerToney65 Ай бұрын

Could you provide the firmware you made? Thanks! This video is amazing.

@TechRallyofficial Ай бұрын

The firmware i made has low print quality issue, i currently use the pre compiled marlin firmware form below link, it will ask for donation enter 0 and continue. Make sure check and change E steps and and probe offset. For sprite extruder. marlin.crc.id.au/

13 күн бұрын

@@TechRallyofficial which one? Ender 3 - BLTouch - SDCard? I couldn't find the file .bin

@TechRallyofficial 13 күн бұрын

No, Select based on the version of your board. Example. Ender 3 v 4.2.2 board witb BL touch.

@amitjadhav3879 Ай бұрын

hello thanks for the details video helps a lot, everything is working well, only when I turn knob clock wise volume gets decrease and when I turn knob anti clock wise volume gets increase, is there any setting to this to work well thanks in advance..😊

@TechRallyofficial Ай бұрын

Thanks for your feedback 😀 Try reversing the data pins for encoder Or you can find and change the pin order in code..

@amitjadhav3879 Ай бұрын

Thanks for reply. Can you please confirm which pin do I need to reverse with which pin..? As of now volume know is stop working not doing anything, only play/pause next and previous function is working....I have no idea what happened, I try to reinstall code 2-3 time but no success....

@TechRallyofficial Ай бұрын

@amitjadhav3879 Data pins of your encoder

@amitjadhav3879 Ай бұрын

@@TechRallyofficial can you make this device wireless with bluetooth module...

@TechRallyofficial Ай бұрын

@amitjadhav3879 i will try bro 😀

@steveniovinelli2176 2 ай бұрын

great Idea! thanks! I need something like this to put a charge into 8 low cells in my battery packl? although I am only hoping it will not push too much into alternate cells? I tried the jumper with 5 volt phone charger it did not work at all! I need something much stronger tatI can adjust! this is it! Much thanks!

@steveniovinelli2176 2 ай бұрын

I have a 20000 mAh battery that 8 cells are low. I also would use this the same way you did! gotta give it a try before spending 300 on another battery. I just forked out all my money so I can get around again! sick of not having my bike!

@TechRallyofficial 2 ай бұрын

Try adding cell balancer, its not good to use cells with uneven voltage.

@MrTaz0079 2 ай бұрын

Thank you for sharing the process, Do you know if I could use my BL touch instead of the CR Touch?

@TechRallyofficial 2 ай бұрын

Yes, you can use BL touch

@MrTaz0079 2 ай бұрын

@@TechRallyofficial Thanks for the reply, just out of interest you wouldn't know what the off set would be with the BL touch??

@TechRallyofficial 2 ай бұрын

Sry bro, i don't know the offset for BL touch You can search in reddit there you can get some information

@AnkylosSpondylos 2 ай бұрын

hi dude. i need help about coding. can u help me. i copy your code and paste. and many times fatal errors. i cant get it. i dm on instg.

@TechRallyofficial 2 ай бұрын

Sure

@KalleKiano136 2 ай бұрын

Good job🙏, but i see that youre using one of those 5.1 channel speaker that usually dont really have bass, please filter some bass only to the satellite speaker. Also instead using arduino, use an led visualizer they are quiet cheap (or maybe find an rgb led that dont use arduino)🙏

@tahaafravi8100 3 ай бұрын

hey i want to made it too but i cant find the Arduino you used do i can use the Arduino nano ch340?? with the same code how i can increase the sensitivity of the rotary encoder ????

@TechRallyofficial 3 ай бұрын

This code works only with any ATmega32U4 based boards..

@darkmightygaming5280 3 ай бұрын

Is this standard 5.1 😅 cause im planning to make one

@TechRallyofficial 3 ай бұрын

Yes, its standard 5.1

@ericmcnair8417 3 ай бұрын

i appreciated this like you wouldn't believe, thank you

@LimaIma1 4 ай бұрын

man i love you <3

@eddieflores7064 3 ай бұрын

I'm in love too. Thanks

@turhapro 4 ай бұрын

rgb lights are ugly as my grandmothers arse.

@yashwantbhalekar 4 ай бұрын

No cooling fan 😮😮😮😮😮

@TechRallyofficial 4 ай бұрын

Initially i planned include cooling fan but while testing it dosen't produce any heat, because it as more efficient class D amp and i used only 12v 5A power supply It my primary amp for my PC and its amazing

@danielreese5043 5 ай бұрын

What are the specs for the Ferrite Core inductor? I'd rather buy than make. Thanks.

@abhijitsarkar6960 5 ай бұрын

This is not a 5.1 amplifier ...there is only 4 channel and power supply must be 19volt - 24 volt

@TechRallyofficial 5 ай бұрын

I used 3 Amplifier modules each has 2 channel, the board works from 12 to 24v.. I wont fake or lie anything in my videos..

@abhijitsarkar6960 5 ай бұрын

@@TechRallyofficial.....I am sorry to say I didn't see the 3rd amplifier which you used one on top of the other 😶

@MrBunnyVr 5 ай бұрын

Can you do a ender 3 one

@TechRallyofficial 5 ай бұрын

Sry i don't have ender 3, but still Its same as the max friend 🙂

@StablestLeaf 6 ай бұрын

Kitne din me ata hai order

@thinkerrobotics 7 ай бұрын

nice project

@rex_rubus 7 ай бұрын

I have also made the same as you exactly same but mine has a bit problem, mine get automatically disconnect(not fully, like the rgb got off, touch not work, knob rotation don't work but light in touch sensor when i touch on them red light glow and light on Arduino also glow) and then I need to re-plug the board sometime it also don't work and need to replug, to fixing the replug button I fix a micro switch between +ve wire. is there any way to permanent fix of this problem

@TechRallyofficial 7 ай бұрын

I didn't face any issue like this Check the pin connections

@HiềnHữu-b8f 7 ай бұрын

me same problem

@LeQuocDat96 8 ай бұрын

Can you help me fix this code without using the 3 buttons: NEXT, PAUSE, PREVIOUS? because I don't know about programming.

@TechRallyofficial 8 ай бұрын

The code will still work even if you don't add any buttons..

@satyarai2190 9 ай бұрын

What's your 5.1 price if any buy this directly.

@TechRallyofficial 8 ай бұрын

Sorry i am selling any thing currently.. Thanks 😀

@jacky_cola 10 ай бұрын

Hello, I have a Question. I have tried a very similar setup, but whenever I try to plug in 2 cables there will be humming/buzzing nosie. The sound will work but the noise is very loud? What can it be and how to prevent that?

@TechRallyofficial 10 ай бұрын

This might be because of your SMPS power supply or poor grounding loop in your audio source. Try reducing the gain in amplifier board potentiometer. And make the audio cable doesn't interfere with other display or power cables.

@BibhasMandal73 10 ай бұрын

I built it its working, thanks

@TechRallyofficial 10 ай бұрын

Great 😀👍

@ShamanETM 10 ай бұрын

He needs masking tape for additional strength because superglue does not work on PVC.

@estonian44 11 ай бұрын

freaking beautiful, everytime i look people like this, i am mezmorized and in aww, want to know how to do it, and when i do it, 🤮

@sumeeths8423 11 ай бұрын

Is it available for sale?

@TechRallyofficial 11 ай бұрын

Sorry currently not seeing.. Thank you...

@dailydoseofkerala3155 11 ай бұрын

So basically u are using your pc as a decoder.. Then amplifying each channel comming out from the pc.... Great job... But this can only give 5.1 out put if you have a pc with you....and also using aurdiuno for led was an overdoing. 😅😅

@TechRallyofficial 11 ай бұрын

Exactly yes... Aurdino was lying in shelf for long time it needs some use..😝 Thank you 😊

@francisxavier5084 Жыл бұрын

is it not TPA3116?

@TechRallyofficial 11 ай бұрын

Its TPA3116

@harman22595 Жыл бұрын

I m about to build this but I got one question. This knob is 360 degree what happened if lower the volume from monitor with mouse, I hope you understand my question

@TechRallyofficial Жыл бұрын

Volume control will work as usual only the led indicator will not show correct level..

@die3ddrucker Жыл бұрын

Sub ❤ nice work! Keep it up

@TechRallyofficial Жыл бұрын

Thank you 😊

@khumanthempoireiton5036 Жыл бұрын

That is some good quality work but you forgot the camera sample

@TechRallyofficial Жыл бұрын

Thank you 😊

@uzairahmed6765 Жыл бұрын

irritating bluetooth noise

@AswanthSharman Жыл бұрын

Can u explain which one is the subwoofer out and how many watts actually it is?

@eddtru Жыл бұрын

Are you aware of the Deej project? Imagine if you could have volume control over a focused window, and when there's no focused window it's master volume control. You would essentially have a volume mixer with one knob.

@prathikguptha183 Жыл бұрын

Hi can u make one for me? What’s the price?

@TechRallyofficial Жыл бұрын

Sorry i am currently not selling anything for now, i will try to do in future. Thanks 😀

@rohitjasuja.mumbai Жыл бұрын

Can you make a 7.1 with audiophile components having 100 watts output per channel at 8 ohms? To make it interesting we can add the ESS9038Pro DAC board also in the unit. I can pay for the entire setup and your expertise.

@TechRallyofficial Жыл бұрын

Sorry currently i am not doing this service, may be i will try in future, Thank you 😊

@newgamersbuddy5136 Жыл бұрын

Can you make it for me

@TechRallyofficial Жыл бұрын

Sorry currently i am no selling anything, but in future i will try. Thank you 😊

@sridharkrishnappanavanerth3388 Жыл бұрын

👍Awesome Video Subscribed! 👍

@TechRallyofficial Жыл бұрын

Thank you 😊

@supratimmondal5071 Жыл бұрын

You have done a great job keeping everything clean and organized. Kudos, and keep it up! 🤍

@TechRallyofficial Жыл бұрын

Thank you 😊...

@tejakesavaram5972 Жыл бұрын

Good job! Bro how can I contact you I have some doubts

@TechRallyofficial Жыл бұрын

Thank You 😀, you can add your questions in comments section

@nitishkumarraikwar2014 Жыл бұрын

Hey bro, I am planning to buy my first 3d printer, please share your insta id to chat and take your advice

@TechRallyofficial Жыл бұрын

Its better to go with ender 3 S1 pro for printing all types of materials, if you are in budget you can go with ender 3 pro neo For maximum size printing check out max version. Search for techrally in insta if need any help.

@karanmalhotra2603 Жыл бұрын

Why don't you reply brother 🤔🤔🤔🤔🤔🤔 please provide your contact number I have work for you

@karanmalhotra2603 Жыл бұрын

Please reply brother , I have some work for you.

@TechRallyofficial Жыл бұрын

How can i help you

@karanmalhotra2603 Жыл бұрын

Please provide your contact details brother ☺️I have some work

Ең жақсы KZbin

Пікірлер