Thanks for this. Couldn't work out how the rails attached to the fronts, lifesaver!

So helpful

Looks so much better than the crap I just got from Howdens. Seems they have gone downhill.

Thanks a lot 👍

Nice demo of why I use DIY Kitchens or Wren, ready built units that slot straight in, lower cost too, for the customer in terms of parts and labour

Great video and watching this as a non carpenter has encouraged me to consider putting these units together myself to save on the installation cost

My units didn't have the machined out holes. Should the runners be matching / same height on both sides of the drawer? I have just measured mine (after installation by a fitter) and the builder seems to have installed them slightly different heights on both sides.

never have i heard countersunk screws called flatheads before

Thank you so much. Removing the front panel was - I don’t get it - the screwdriver turn - BRILLIANT 😊

3 years on and still no instructions big thank you

Lifesaver mate - I was trying to figure out how to raise the plinth drawers to take account of new flooring - saved me a right hassle! Ta!

Thanks for the video. Very helpful. However, if you have a 2 pan drawer and the bottom drawer is not seeming to level up with the cabinet- can you please advise? Do we need to make our own holes for the door fronts for example? Thanks in advance

Excellent, many thanks for posting this as it told me how to resolve the problem when your fitter used the short screws to put on the drawer fronts. We went in to Howdens but all they could offer was more parts.

This was so helpful, thank you.

Trying to find video for 500 mm recycling bin. Any one know if there is one. Can't follow the instructions. They are useless

Cheers ram Pulled me out of a hole there 👍🏼

Life saver. Kitchen fitter had put tiny screws in the door mounts all fell apart. Needed to know how to strip them down. Great video 👏🏼

Cheers.... Excellent

Thanks so much for taking the time to do this. I'm doing internal drawers but guessing it's quite similar. Cheers

Nice one mate!

Great video. Really helped me with assembly. Thanks.

Front panel just came off a drawer in my kitchen. Just watched this and realised my kitchen fitters didn't put the drawer together properly. I also believe the _reason_ the front panel came away was because they used the shorter screws. Not quite sure what to do ATM. Seriously looking at Araldite to repair the chipboard and re-make a pilot hole. Thank you for showing me how to get it apart and how to put it together properly. Edit: of the 4 screws on the front panel, 3 of then were the short type. As it was a _repair,_ I decided to use 3.5 x 20mm screws, and as (obviously) the screws in my kitchen are all over the place, I got a box of 200!

Top Man..!!

Thank you for sharing, priceless to help us put the cutlery drawer front back on :)

brilliant - just what i needed. thank you

thank you sooooo much for your video ! I was completely lost ! ^^

You are a star! Great video, saved my bacon. I cannot tell you how useful this was for me. A million thanks.

Thanks Ram. This is everything that’s missing from the Howdens manual!

Got almost identical pan drawerbox from wickes and the instructions for the runners are almost non existent. Thanks for this video which amswered all my questions.

Anyone else at work? 🤣

Thanks fella, i just got the Howdens kitchen, having loads of problems with the oven tower, which has the door up top and draw on the bottom., had to drill loads of holes so the 2 AEG ovens fit, what a load of rubbish it is, i really regret my purchase from this company, wish i went to Magnets now... £7000 wasted on units only!

15:33 what do you call that part that clips in? it's broken and i cant find it anywhere : (

You are an absolute star, thank you so much for posting this!! 👍

Thank you soooo much. I was clueless and stressed. But this well documented video is perfect. Thanks again.

Great explanation!!! Thanks, helped me out.

How do you take the clips out it it’s wrong

Excellent video, thanks

Good , really help ful video thank you

2 of mine are stopping on the return about 1cm out. The soft close seems to only take them that far and then I have to push the rest in. Any ideas why? Is the mechanism too stiff and will loosen?

Mate! You saved my sanity. Opened up the box and couldn't believe that there were no instructions. Sat there for ages trying to work it out. Then I watched video. Thanks so much

I subscribe you channel..

How do you take the clip out when the doors are loose? Ducking impossible.

Howdens are shocking no instructions random bag of screws

Excellent I followed your step by step guide video with no problems, as one as already commented Howdens paper instructions were next to useless your a life saver I can't thank you enough.

I tell you what fella , without this video I would have been screwed , no assembly instructions from Howdens In the draw pack , pretty P**S poor from HOWDENS ! You however Legend ! Thanks for getting me over the winning line 👍😀😅

I've installed these but the drawers are really stiff coming out, why is that?

DRAWERS!

Unpacked the drawers this afternoon and thought I would need a degree to assemble. It said consult the Howden's kitchen assembly guide. Which I don't have!! Absolute lifesaver. Thank you.

Tidy work. Nice job. Clear demo and well presented.

Good stuff, but in the intro it says you will show us how to adjust...I guess you showed us which screws on the mnechism do it, but I would have like to see it in action. I shall go downstairs now and experment for myself...