Do you even get a decent smoke flavor with all that paste lathered on it? lol

Too close on the camera work

Nice.👍

Pode me instruir melhor em português a cerca da eficácia deste aparelho? Posso fazer demarcação com este aparelho?

Hello thank you for the video it is thanks to you that I found the fault it was the fuse on the right side which blew I have a question can I replace it with a standard 8 Ampere fuse or take the same reference as the old fuse written on it T8L 250v . thanks

Este gps sirve para hacer trabajo de topografía o cual me recomienda

Useful information 👍🏻

Wow it's look delicious 😋 well done our new gen Chefs 👋👋👏👏👍👍

Looks 😋 👏👏👍 from Sammy, Danny

Yummmyyyyy

Looks delicious 😋

Your knowledge about this unit is fantastic but I could not follow you with the computer screen work. I have this same unit and find it complicated to work with when you only use it once or twice a year.

Lovely 😍

Very helpful!

Can you put the link for the light assemblies

Great video! I would have tried to take off the whole lens if I hadn't seen this! But were you changing high or low beams? The H11 is high or low? What was the small one you took out first and put in last?

Would have been great to see a before and after comparison of how they look at night. 😩😞

How have these held up since you installed them? Still working good? Any issues?

Nice video, thanks! Have you got a link to the ones you recommend?

Christmas lights for general lighting! That's a great idea! Thanks for the video.

Thanks for the upload. Quite informative. All I need now is to buy a Nissan leaf.

Is there any benefit to using white vs black liner?

You can use the plastic you use to cover the ground...wrap it 12+ inches high and pin nail with pin nail gun...1 inch pin nails w washers, Then vapor tape the seam and vapor tape ( 4in sticky tape) the bottom 4 sides. Many company's mastic goo with paint brush the top to seal...some use expanding spray foam on the top. Tip: fold the top down 1/2 inch or more so the top has a lip so the spray foam has something to sit on. Beat thing to do is go to a subdivision in your area that is new and homes are being constructed that have sealed crawl spaces. Always finish the project with a remote humidity temperature gauge that tells you from your first floor what the humidity in your crawl space is...at a simple glance. Seal your sill plate for optimum sealing and hydrocement any below grade pipe penetrations..ie: sewer...put a hose down your gravity drain for 30 min and see if it backs up...better to know now than when you have a pipe leak and your crawl is a swimming pool. Hope that helps... www.SealedSolution.com Would you do it again...looking back? What humidity numbers did your crawl space produce...on average.

question my crawl space half is wet the floor I think the water came from underneath​ ,if I use the plastic will help with the ugly smell ???

nice job !!!!! the dimpled black plastic. is the stuff that is used on foundation walls? and what sort of plastic did you use over the black membrain?

Nice video. You did not install a dehumidifier or some sort of a sphere air system?

Where did you purchase the thick dimpled membrane? What brand is it?

Good stuff! Absolutely awesome video and great explanation as to the benefits of having a vapor barrier. You just made my decision to install this so much easier

great video, thanx.

Very thorough commentary. Thanks!

Very nice job. I think you could perform surgery in that crawl space. Working on a similar project and found Delta Drain MS but Superseal is more readily available to non-contractors I think. Looks like a good product.

Where did you get the material that you laid down first?

Great Video. Did you buy the materials at any location? I am looking to do the same project and see SuperSeal as the preferred product for the membrane. What did you use for the plastic liner? Thickness used?