@@DanSvoboda-hg5mm ade Forman light engineering on eBay man 👍
@YootubeUK3 күн бұрын
Horrible job just to replace those backplates! That poor E46 was well rusty, still we gotta save 'em if we can. Good video. O'LearysGenuineBMW (give him a like & follow) covered rear hub removal in his video here should anyone or you Brady be doing this again in the future > kzbin.info/www/bejne/mpDZiH2lnMSKZ6M.
@mrgall794823 күн бұрын
looking good Brady, hope all well bro
@bradytruezero873923 күн бұрын
@@mrgall7948 thanks man and yes great thank how all it good with you 👍
@infamousaidyАй бұрын
Looking good, what thickness aluminium did you use? I made some ABS plastic ones at the weekend but they are a bit floppy so I may step it up to ali. Cheers
@bradytruezero8739Ай бұрын
@@infamousaidy I will check for you and get back to you later I can’t remember of the top of my head 😅
@infamousaidyАй бұрын
@@bradytruezero8739 cheers, appreciate it.
@bradytruezero8739Ай бұрын
@@infamousaidy they’re 2mm but with the dimples in them they’re surprisingly ridged and went with the thought process to cut a little weight and I won’t actually be standing on them just to rest my heels on and also not to wear through the floor paint
@infamousaidyАй бұрын
@@bradytruezero8739 ideal cheers. If mine are too floppy and annoying I might do aluminium versions. Or make it in steel and then use it as a mould for carbon haha
@e4tnu150Ай бұрын
HI MATE ANY CHANCE I COULD FIRE A FEW QUESTIONS AT YOU REGARDING YOUR AUTO SWAP PLEASE ?
@bradytruezero8739Ай бұрын
@@e4tnu150 yes no probs man what would you like to know?
@e4tnu150Ай бұрын
@@bradytruezero8739 GREAT MATE THANKS, I'M JUST ABOUT TO START A MK1 AUTO CONVERSION TO MANUAL WOULD YOU KNOW IF I CAN USE THE PEDLE BOX OFF A MK2.5 , DID YOU HAVE TO CHANGE THE ECU TO MANUAL OR AFTER MARKET, ALSO WAS THE WIRING ON THE GEAR BOX PROBLEMATIC ? I WILL BE DROPING A SIX SPEED INTO MINE AND A LTD DIFF . ANY ADVICE WOULD BE APPRECIATED. MANY THANKS ..
@bradytruezero8739Ай бұрын
@@e4tnu150 tbh I couldn’t tell you if the 2.5 pedals would work unfortunately but I kept my auto ecu, there is a little bit of wiring you need to do for the car to start and for the clocks to work but with a little searching online you found what wire to connect together ect
@e4tnu150Ай бұрын
@@bradytruezero8739 OK MATE THANKS , I WAS'NT SURE ABOUT ECU BUT I WILL GO AHEAD AND USE MINE . SO ARE ALL YOUR LIGHTS WORKING REVERSE , BRAKE AND NO ISSUES WITH NEUTRAL ?
@e4tnu150Ай бұрын
Great video nice fabrication of the foot well plates. Will you be putting sound deadening underneath?
@bradytruezero8739Ай бұрын
@@e4tnu150 Thank you 🙏 and no sound deadening
@e4tnu150Ай бұрын
DID YOU KEEP THE STARTER MOTOR THAT CAME WITH THE AUTO MX5 AND USE IN THE CONVERSION OR DID YOU SWAP IN A MANUAL ONE ? JUST ASKING AS I HAVE A SWAP PLANNED. CHEERS.
@bradytruezero8739Ай бұрын
@@e4tnu150 yes I used the auto starter 👍
@e4tnu150Ай бұрын
Brilliant thanks 👍
@matthewrussАй бұрын
looking good dude, i cant wait to get my st nad legacy fied so i can finally get on the wrc car ;) or replica i should say lol
@e4tnu150Ай бұрын
SHAME ABOUT THE MX5 VIDEO 😖 BET THAT WOULD HAVE BEEN USEFULL TO ALOT OF MX5 OWNERS .ALSO TOP TIP FOR REMOVING THE BALL JOINTS..
@davidg.99424 ай бұрын
learnt something new today,,, mine is rwd so it is bit different, all goes to the drive axle vs trailing arm on yours, had to watch over and over again one part because I got stupid for a moment 😂😂😂
@Shimshams4 ай бұрын
Thank you , now to do my mates handle 👍
@ryanknight5614 ай бұрын
Does the door handle sit flush underneath ? I replaced one but the handle doesn't seem to be sitting flush only at the bottom and now the door ks temperamental with opening and not opening
@bradytruezero87394 ай бұрын
Yes mate from memory, have a check of the opposite side to confirm how it should be 👍
@ryanknight5614 ай бұрын
@bradytruezero8739 ok yeah will have a look, just couldn't get it to sit flush which was annoying
@pouldammrasmussen68854 ай бұрын
Had same problem. Watched this video. And the job was an easy fix. Thx
@bradytruezero87394 ай бұрын
Thank you 🙏
@e4tnu1504 ай бұрын
Nice one , looking forward to the gearbox swap content.
@bradytruezero87394 ай бұрын
Thanks mate appreciate it 👌
@ro5northco5 ай бұрын
Great video thank you 👏🏼
@rceyy36487 ай бұрын
What engine car was this for?
@bradytruezero87397 ай бұрын
Was for a 325i
@oktanskioktan93728 ай бұрын
You should at least clean and paint the caliper...
@bradytruezero87398 ай бұрын
Would have like to do that but for the purposes of the video painting it was not necessary
@nikoladukanovic-iu3gu9 ай бұрын
Do you know what a fc3s is?
@bradytruezero87399 ай бұрын
An rx7?
@nikoladukanovic-iu3gu9 ай бұрын
@@bradytruezero8739 it is like a rx7
@nikoladukanovic-iu3gu9 ай бұрын
@@bradytruezero8739 a fc3s is a good car to start drifting
@nikoladukanovic-iu3gu9 ай бұрын
Very cool
@veritasaequitas987510 ай бұрын
1:17 Where's the rotor?? How did you get the rotor off with the calliper in place???? Were you driving around with no rear brakes? What's that all about?
@bradytruezero873910 ай бұрын
The rota was removed before and the caliper put on so it wasn’t dangling
@veritasaequitas987510 ай бұрын
@@bradytruezero8739 Ok. Great video man. Covers all the important bits. Like how to do it!!! Where did you get that puller kit and slide hammer?
@bradytruezero87399 ай бұрын
@@veritasaequitas9875 thanks man appreciate it and eBay years ago 👍
@SWE33211 ай бұрын
Please can you let me know why you would change to a 6 speed box? Motorway noise in final gear? Top speed?
@bradytruezero873911 ай бұрын
I was done on a mates car and he uses it for drifting, I believe the 6th gear noise is ok when cruising and in redness for drifting rather than using second gear and being high in the revs but 3rd was to much and would grip up, he was happier with the conversion as the heating was better for drifting
@e4tnu150 Жыл бұрын
A great video will come in handy ,also was the conversion done to a 1.6 or 1.8 ? Can it be done to either?
@bradytruezero8739 Жыл бұрын
It was done to a 1.6 and I’m not sure with the 1.8
@e4tnu150 Жыл бұрын
Is the speed sensor for the gearbox just a simple swap or is it a bit more involved?👍
@bradytruezero8739 Жыл бұрын
@@e4tnu150 from memory we swapped the sensor and re wired the plug on the end of it
@PiOfficial Жыл бұрын
Where are your brake discs???
@bradytruezero8739 Жыл бұрын
They where already removed by the previous owner
@s13zenki Жыл бұрын
The nut was pure aids to reinstall 😭 you wish they were all threaded at the bottom
@s13zenki Жыл бұрын
Thank you very much 🫡 helped me with my e34 alternator 😅
@GaragE36uk Жыл бұрын
Nice extra bit of space you will gain there.
@bradytruezero8739 Жыл бұрын
Yes man, be a nice change to have some usable work space
@GaragE36uk Жыл бұрын
@@bradytruezero8739 that your own garage at home I take it?
@bradytruezero8739 Жыл бұрын
@@GaragE36uk yes man 👍
@jamesfawcett442 Жыл бұрын
Got all this to do in the next few weeks. Good vid thanks
@Boom-tj6nn Жыл бұрын
Any modification needed to used a nb? Like wiring?
@bradytruezero8739 Жыл бұрын
You have to cut the reverse wiring plug off and swap the plug to the 6 speed reverse light wires
@pawpatina Жыл бұрын
any hardware store, usually near the paint section or the masonry section.... Concrete etch and prep. make sure its just 100% phosphoric acid. wear eye and face protection and spray all that rust with it. converts it to iron phosphor and wont rust anymore. then spray it with some rustoleum paint.
@North_Motorsport Жыл бұрын
Thanks for the mention man, nice driving with you! Great video
@bradytruezero8739 Жыл бұрын
Thanks man! 🙏
@K3BABB Жыл бұрын
Awesome day! 💨
@bradytruezero8739 Жыл бұрын
Yes it was man and looking forward to next year!
@GaragE36uk Жыл бұрын
Decent video mate, some good laps there
@bradytruezero8739 Жыл бұрын
Thanks man, appreciate it, felt a bit sketchy as I’ve not driven on a while 😅
@GaragE36uk Жыл бұрын
@@bradytruezero8739 yes same for me, plus in a new car I had never skidded before, took a bit to get used to..
@GaragE36uk Жыл бұрын
Hopefully get my video out by Friday..
@bradytruezero8739 Жыл бұрын
@@GaragE36uk look forward to watching it 👌
@jasondavies6310 Жыл бұрын
Basic setup but it works I went all in fanatec spent crazy money dd1 Porsche wheel but I rather drive my Mazda MX-5 it's standard at the moment
@bradytruezero8739 Жыл бұрын
Awh nice man and yes basic for now to see it I get on with it and I plan on upgrading slowly as I progress
@kamilddl5764 Жыл бұрын
good work!
@kamilddl5764 Жыл бұрын
lot of work but this is beauty car good luck and power!
@bradytruezero8739 Жыл бұрын
Thank you 🙏
@matthewcrozier5979 Жыл бұрын
Just after fitting ridge front and skirts with edge rear quarters/bumper. Those voids on the quarters I put fibreglass paste in there so when I tightened the fixings it didn't pull the panel in.
@bradytruezero8739 Жыл бұрын
Thanks man I’ll keep that in mind when I’m ready for final fitment 😊
@matthewcrozier5979 Жыл бұрын
@@bradytruezero8739 no worries man can send you pics of them. I used stainless rivnuts and stainless panhead bolts to fit mine.
@bradytruezero8739 Жыл бұрын
Thanks man and I’ve got the same ready for mine 🙏
@alandrury61225 ай бұрын
@@bradytruezero8739 & @matthewcrozier5979 where did you guys order your kit from been looking for one for a while now
@pieced_by_oda65752 жыл бұрын
nice setup man!
@bradytruezero87392 жыл бұрын
Thank you 🙏
@dinoleonida54862 жыл бұрын
What kit did you use for this?
@bradytruezero87392 жыл бұрын
It was a kit from ebay 👍
@curtisarchery932 жыл бұрын
She's looking good 👍
@bradytruezero87392 жыл бұрын
Thanks man she’s getting there
@bobdean81652 жыл бұрын
🅿🆁🅾🅼🅾🆂🅼 ☝️
@MalcomMcLeod2 жыл бұрын
2:22 Those T-nuts are in upside down. The ball bearing should be facing the rail.
@bradytruezero87392 жыл бұрын
I realised that when I had it finished assembling it 🙄😂
@alluneed77632 жыл бұрын
Where did you sell the cats?
@bradytruezero87392 жыл бұрын
Just at local scrap yard
@SuperFlash9902 жыл бұрын
Awesome video. Thanks for the knowledge! I was curious about replacing a dust shield. Would I have to bleed the breaks if I were to replace the dust shield?
@bradytruezero87392 жыл бұрын
Thank you 🙏 and no need to bleed the brakes when changing the dust shield 👍
@SuperFlash9902 жыл бұрын
@@bradytruezero8739 Thank you!!!
@matthewruss2 жыл бұрын
Inbox me with a link for that man i totaly forgot about that stuff lol
@jamiewalters54802 жыл бұрын
Great vid pal
@bradytruezero87392 жыл бұрын
Thanks man 🙏
@karlneofitou47302 жыл бұрын
👍😎
@jamiewalters54802 жыл бұрын
Paint nxt dude
@bradytruezero87392 жыл бұрын
I need to collect a few more parts first 😉
@K3BABB2 жыл бұрын
Awesome day! 🔥🔥
@bradytruezero87392 жыл бұрын
It was man can’t wait to go on the next one with you 😜👌
@teamhakitota2 жыл бұрын
Good driving bud!
@bradytruezero87392 жыл бұрын
Thanks man I was chasing one of you guys towards the end of the day 😁