Do not take the screws out completely, every manual will tell you ,same with the manufacturer.
@chesstime356 Жыл бұрын
Great 👍 job man nice video
@westsidehvac10972 жыл бұрын
you don't have to completely remove screw
@db34673 жыл бұрын
What brand is thecmanometer
@WreckingCr3W24 жыл бұрын
you don't use barb fittings to screw into your valve when you check pressure?
@herculesskinny20304 жыл бұрын
Typical hands of a hard working man.
@JulesODwyer4 жыл бұрын
Don't think you have to remove either of those screws just back out say 2 turns then put your hose over the valve port
@workinprogress0084 жыл бұрын
A little tip: You don't have to remove the cap inserts to check the pressure. Just loosen them a full turn and slip the tubing over it. Saves you from possibly losing those tiny caps. I like Eucerin for my hands. Lol Edit: Thanks for the video!
@williammarik61593 жыл бұрын
Yes.Rheem says not to remove the screws. Like you said,one full-turn. By the way,i use Eucerin too. I have arthritis in my hands. Good stuff.
@lzgamer81332 жыл бұрын
Can you please upload a video this procedure?
@jamesgillies37104 жыл бұрын
good job
@amirikiri41124 жыл бұрын
Pass my mans the lotion.
@julies1ify3 жыл бұрын
ashy for sure
@gtownhvac16405 жыл бұрын
Great video...
@ronwalker28875 жыл бұрын
Thanks for the info Eric. Great video.
@mark.r89005 жыл бұрын
hi what is the hose size that goes to the gas valve( the small short section). also what is the allen key size? on some gas valve you have to add a brass hose barb fitting and then connect the manometer hose. do you know what is the size of this brass fitting? thank you.
@paulclark84205 жыл бұрын
All gas appliances in the house should be running when doing any calibration to the unit or the gas system.
@SeymourAss545 жыл бұрын
Just for the inlet pressure though right?
@paulclark84205 жыл бұрын
@@SeymourAss54 when another appliance comes on, manifold pressures on all other appliances will drop. So calibration should be done to all other appliances also inlet pressures.
@wildman86016 жыл бұрын
And yes I didn't hit the right button to 0 out
@wildman86016 жыл бұрын
Cool video bro but Damn get some lotion on then ashy hands lol
@juliocv7195 жыл бұрын
LMAO
@SuperLORENA884 жыл бұрын
Yea bro, eat some carnitas and rub the manteca on your hands.
@mikelewis42606 жыл бұрын
I noticed when you checked the gas pressure coming in you didn't zero out the manometer. That could have possibly gave you the slightly high reading.
@youngjedi55996 жыл бұрын
Thanks Eric. Really good and informative video. Keep me coming
@ericthecomfortdoctorcook11817 жыл бұрын
Thanks I Will Change That! I Must Have Hit The Wrong Button! Lol
@5822huron3 жыл бұрын
Eric are you out of illinois?
@Impedancenetwork7 жыл бұрын
Do you know you spelled "manometer" incorrectly in the description? You spelled it "Nanometer." I hope you don't actually think it is spelled that way.