Thanks just had the same problem

I’ve had mine and been using it almost daily. Its one of the brightest lites I’ve used. Its a little big and cumbersome for EDC and wished it came with a carry pouch you install on your belt. I’ve terrible luck with the smaller Coastal flashlights and was ready to give up on them until I got this one as a gift over a year ago. I hope I get long term use out of it. I really like the battery shell that comes with it to put your own batteries in it to use while the recharge pack is charging. I also like the dimmable modes it comes with.

Update please

I opened mine and the cold container had 2 inches of ice at the bottom! Thawing it now and will add more if it doesn't work after that.

Gotta have man hands. Threw mine out. Great video though.

I have a ge profile J B968S0K1SS. You saved me a lot of work. Thank you.

Thank you so much for saving my night. All the other videos mention equipment that I don’t have. You only utilized a drill which is what I have. Thank you for walking through step by step. I had snapped off that slow close thing not knowing what it was. I had to stick it back and luckily it worked ❤

Is it loud? I'm thinking of putting it in my bedroom.

Do u reco.mend it? Is it loud?

I just installed this model only to find out the door was dented on the side and it wouldnt close, I get to do it all over again tomorrow lol.... thanks for the video it was excellent! My only problemwas I had to install the electrical LAST as my wire coming out of the floor was too short :-(

Hi! I just did all of this and now I’ve put a test batch of water in and even though everything is plugged in and switches are on now the machine isn’t working

Thank you! So helpful.

If you don’t want to remove the button.You can just take an air hose and blow out the tubing connected to the cold dispenser button/line. Follow the line to where it tees from the tank and goes to top corner near the screw you removed to take off the lid. It pops rights off. While blowing, hold the button down.” I did it with water in the tank . It unplugged immediately now running a safe cleaning solution through with hot water to clean.

Thank you

Removing that grounding strap from the alternator end housing does not break the neutral/ground bonding, that has to be done in either the end housing of the alternator or in the control panel depending on which one the manufacturer chose. Read the directions before assembly.

Thanks for the preview. I am planning to contact them with my first order and this provided some good preparation regarding what to expect!

Mine keeps doing a Purple Heart and beeping when trying to connect

Just did my swap out today thanks for the instructions videos

Really helpful video. Thanks!

Thank you sir for the help

It gives me the code but when I hold it in front of the camera is just keeps beeping and retrying and then finally gives me an error message that it failed to "bind". So I reset the Ebo and keep trying again but it fails every time.

Hello. Mine won't connect. I've re-started many many times. Any idea what I might be doing wrong?

Very good. Thank you for the thorough demonstration, and the honesty when it came to the glass. Much appreciated.

You didn't show it going up and that's what I came here for. I suppose you angle it in with the brackets you're forced to use on this one?

Thanks! But the upper side of those grommets would be called the “convex” side. Not the concave side….

Awesome video! I was on Amazon ready to purchase a new staple gun and decided to see if there was a way to 'fix' my old one. I followed you every step of the way...pausing and rewinding several times...I am proud of myself! My old stapler is working again! Thank you dear sir!

did u cleaned it before using i forgot to do ours 😆

Impossible à ouvrir…

70 bucks for that contraption is outrageous

Nice Presentation …. Was really struggling to figure this thing out… your vid was a BIG help

Thanks!

Thanks alot this worked for me. How to prevent this in the future?

I can’t get mine to connect!

At your 1 min. 20 sec. mark: I can't seem to remove the top lid to that part :( My Avalon water cooler stopped dispensing water recently as well, and I would love to fix on my own. But I guess I just don't have the muscle. Pity, I've only owned this thing for about 2 yrs. Not a good return on investment, but I do really love using a water cooler vs. bottled waters (less waste in landfills). Thanks for your helpful video.

I can never get the damn caps off.

Went to Home Depot today. I had to cancel the delivery of the same unit. So far all this combo front loader washer and dryer requires 2 power plugs. 220-240v for Dryer and 120v for washer. Whether it’s LG, Samsung etc. We were at Home Depot and the guy there checked all the backs of the unit. The only combo washer and dryer with a single plug are the GE or Frigidaire top loader that usually can be seen in a condo or apartment unit (220v 4 prong) We have a broken GE combo unit that uses 4 prong plug. (That’s the only connector we have in the wall) and we ended up buying the same shitty brand.

@ so nothing is connected to your 120v outlet? I’m chatting with home depot and they are saying it requires 240V plug for dryer (electric) and 120V for washer. Was there a certain connection on the 240v plug to get power access for the 120v washer so it only requires the single 4 prong plug to power both? I called home depot and they said need 2 connections . 120V for washer 220V for dryer. Both electric. I’m heading there to cancel and order a single 220-249v combo unit.

Is there a reason why you don’t cycle the water through while plugged in?

Video was very helpful. Does the battery fit 2016 Highlander Hybrid platinum trim?

Got 2 rings off a fixture we brought home from Habitat ReStore, the 3rd starts moving then hits what feels like a hard stop. Channel locks would just crack the porcelain lamp socket. Using pipe fittings is brilliant. Please post the sizes you used! I dont know these on sight.

Good video. The batch feed insinkerator is a bit different install.

Thank you for the great explanation, even two years later. I am installing these shortly.

Thank you for all the information I needed.

Super helpful video! I need to replace my 12V. Haven't checked dealership yet since it'll be $$ probably. Where did you get your battery from? Can't seem to find online anywhere except Europe. I'm in US..thanks! O'Reilly's recommended using AGM battery but our current one is standard and I don't want to switch it over..

LENOVO HAS THE PROPER PROCEDURE

This is exactly what I needed! Also, I want that ladder

Very useful video, saved me a lot of guessing and frustration when mine jammed. Thank you!

I’m about to tackle this so I thank you for taking the time to share. I was curious about being able to remove the entire seat and placing it on a workbench to make it easier but not sure if you can because of the wiring. I need to see if there is a single plug to disconnect to disconnect the seat entirely. Only other issue I see is that the seat bottom seems to have lost its shape like mine did and I believe that it will cause the new parts to break again sooner than expected. They broke because the weight of getting in and out of the vehicle causes stress on the plastic. I’m planning to replace the seat bottom foam so it’s more rigid again before I put the new parts on. Once again thanks for sharing this. It was helpful and educational.

What’s the reason for changing the doors from one side to other side?

Your video is really a big help. I just couldn’t figure this thing out. The instruction book was of no help, typical Chinese instruction manual.